Question about Nissan Stanza

2 Answers

How to replace front wheel bearings and CV joints on a 1991 Nissan stanza

Posted by on

  • Anonymous Mar 17, 2014

    replace cv joint

  • Anonymous Mar 31, 2014

    What other cv joints can replace the original

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Need repair information on 2002 nissan quest cv joint

Posted on Nov 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 2 Answers

I can tell you on a 93 Altima that you have remove the entire wheel knuckle and press it out from the rear. Yeah, the knuckle, remove the strut tower bolts, drive train ( which can be lighty pressed out ), caliper and bracket, and remove the ball joint. There's a snap ring at the back of the wheel knuckle that holds the bearing, then press it out with a socket and a table vice or something to that effect. By the way the going commercial rate if you take it to a shop and have them do it starts at $150 for labor. Worth it, oh yeah.

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace cv joints on a 1985 nissan stanza


It's better to buy a manual. find them at you local auto part store. There isn't enough space in here to explain. I've replaced stanza cv before, just be careful, For your safety use jack stands.

Feb 12, 2016 | 1985 Nissan Stanza

5 Answers

Does the 1988 Nissan Stanza have U-joints? The reason I ask is because when the car shifts it jolts. And when you put it in gear it jolts and vibrates. I looked under the car and I dont see a driveline. Is...


Hi, yes you have front wheel drive. The drive shafts are on each side going from the transaxle to the wheels. each axle has 2 constant velocity (CV) joints. This is a bit different than a U-joint but serves the same purpose. There are 2 indications of a worn out CV joint. Id the boot is torn, the CV will wear out due to dirt getting in. If you hear a popping noise when making a sharp turn, that is a worn our CV joint. If your boots are intact and there is no popping on turns, the odds are the problem is not with the joints but somewhere else in the drive train. Raise the car and turn the wheels by hand to see where the play is coming from. let us know if you have more questions, and thanks for using FixYa.

front wheel drive axle:

jturcotte_170.jpg

Jan 20, 2011 | 1988 Nissan Stanza

1 Answer

Makes a growling sound from the right passenger side especially when you make a right turn.


Sounds like a wheel bearing or possibly a cv joint. If the noise gets louder the faster you get it's a wheelbearing if it only does it going round tight corners it's probably a cv joint

Oct 04, 2010 | 1990 Nissan Stanza

1 Answer

My 1991 cavalier is a 2.2ltr 4 cyl. 3spd auto, front wheel drive. when I drive it I hear from the right (passenger side) front tire a deep loping whirring sound....I am leaning towards the bearing or...


Deep growling sound could well be a bad wheel bearing. A bad cv joint will generally make a click or clacking sound, usually while only turning. While driving, you can often change the pitch of a bad wheel bearing with a slight turn of the steering wheel (note - slightly, no crazy zig-zag). What you're doing is shifting the weight on/off of this bearing and the pitch will change if it's bad. Only way to verify is to remove it and feel it in hand. It's a sealed hub/bearing assembly and only replaceable, not serviceable.

Jun 20, 2010 | 1991 Chevrolet Cavalier

2 Answers

Clicking noise coming from front driver side wheel/tire as car is in motion. Sounds almost like there is nail/screw stuck in the tire. Upon inspection, i didnt find anything stuck in the tire. What is this...


Wheel bearing is bad and will need to be replaced. This is a somewhat easy job if you are comfortable with mechanics, but you will need to remove a lot of parts to get at the bearing. You can get a new bearing at your local auto parts store. Please rate

May 31, 2010 | 2006 Nissan Maxima

1 Answer

Cv shaft replace


This is usually the same on all front wheel drive cars..

Remove the wheel

Remove the brake caliper

Remove the brake rotor

Remove the spindle nut

Remove the wheel bearing assembly (usually 3 bolts)

-The next step may be optional, depends on the car-
Unbolt the lower ball joint (under the A-frame, some are riveted, if so, drill them out and chisel or just chisel them off with a metal chisel, sometimes you can cut the rivet heads off with a sawzall then pry it apart from the a-frame)

Pull the wheel bearing assembly from the spindle of the CV half shaft.
(Sometimes you need a wheel puller)

Once its loose, all you have to do it yank it out, and push the new one in. Make sure the new one pops in and is seated firmly.

Reverse steps for re-assembly. If you took the ball joint loose and it was riveted, use hardened steel bolts and nuts with lock washers to replace it, or buy a new ball joint, they aren't that expensive and it will come with bolts.

Good luck

May 09, 2010 | 1992 Nissan Stanza

2 Answers

Alot of road noise from front of car, suspect cv or drive train issue , As speed increases noise gets louder. Engine runs smooth, new tires 6mos. ago, alignment good.


MOST LIKELY CAUSE OF THIS IS THE WHEEL BEARING, DEFECTIVE CV JOINTS ONLY MAKE NOISE IN TURNS AND THAT IS A CLICKING NOISE,.

Mar 16, 2010 | 2004 Nissan Sentra

4 Answers

When making a left-hand turn, a loud grating noising comes from the passenger side front wheel assembly. The frequency of the noise increases with speed, and the intensity of the noise increases with the...


ck the CV boot. if its broken you need a new cv axle, if its ok, jack up the car so both wheels are off the ground. either put the car in drive or just manually spin each front wheel while gripping the coil spring for the front strut. if you feel any (roughness) at all, that wheel bearing is bad. it should be smooth. if you have a bad one you will know it by this method. Even good mechanics sometimes replace the wrong bearing, but this 100% works every time.

Sep 18, 2009 | 1995 Nissan Maxima

1 Answer

Need info on replacing the front wheel bearings on my front wheel drive 1985 Nissan Stanza?


WOW...85? Go to AutoZone or Napa and order a Chiltons manual ($25)...
Good Luck getting parts

Jun 23, 2009 | 1985 Nissan Stanza

1 Answer

Front spindles


ok... replace them....inspect the bearings and replace if necessary....
Robert
and have the cv joints inspected as well.

Sep 05, 2008 | 1991 Nissan Sentra 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

739 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...