Question about 1987 Plymouth Gran Fury

1 Answer

Replced sarter relay in my 1965 426 wedge 4speed, engine starts but will not run

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Plymouth Master
  • 975 Answers

Got to be the ballast resistor. Small white ceramic block on firewall,used to cut the coil voltage down while running.
While the key is in the start position,the ballast is bypassed,if it dies when you let off the key ,check the ballast.

Posted on Apr 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my car shut down


Fuel relay is what I would look into next. Check the temp of the vehicle to when it shuts down.

Jul 21, 2014 | 1995 Pontiac Grand Am

1 Answer

1984 ram 150 225 engine 4speed starter?; at first


have you tried to roll the pickup and put it in first gear because you have to roll the pickup to a certain speed like 10 mph or so and then put it into first gear should start the pickup. If this does not work that you have serious engine problems with that old pickup and might be inside the tramsmission problem. So let me know if this works out

Jun 09, 2011 | 1984 Dodge Pickup 4WD

1 Answer

My volkswagen beetle 2002, i lost the micro chip of the key swich and its not starting with in other swich which bought it from dubai and dont know what to do? please help


Defeat it! but make sure no one knows find the sarter relay put it in the close postion then put it back crank the car it should start

Apr 22, 2011 | 2000 Volkswagen Beetle

1 Answer

Where is the starter and how do you replce it..the starter just started clicking


Replacing the starter is labor intensive. You access it from under the car. I'm not sure of which engine you have in your Eldorado. But before you change the starter make sure it's not the battery or a relay. The clicking sound is usually a battery or relay problem.

Feb 15, 2011 | 1995 Cadillac Eldorado

1 Answer

Im replacing the sarter on a 1987 S-10 Tahoe 4x4 w/2.8L V-6.Im using shims and with or without them I cant get the sarter to stop whining.And no,Im not a mechanic,I just cant afford one right now.


right before you do anything else ,start the engine then take the small wire off with the engine running and see if teh noise stops as it could be a faulty ignition switch and the contact inside the switch isnt releasing ,then leave this post on E mail and if you still need help reply but please remember the itme zone difference .

Feb 02, 2011 | 1987 Chevrolet S-10 Pickup

1 Answer

Cooling fan motor will not run i just replced


driver side strut tower
firs and last relay any way u want to look at it dont mind the other relays just the two outer relays
make sure the ecu signal is working
warm up the car and disconnect fan motor make sure tha you have ggod ground get a test light and check for the litr green wire to see if its going to send signal to the wire

Jun 12, 2010 | 1993 Dodge Caravan

2 Answers

1999 Chevy Blazer Engine will not crank over. All


try turning the key over to the start position. then take a long screwdriver and touch it across the terminals on the starter. this should start your vehicle. if the sarter doesnt turn when you do this,then you have the starter locked up,and yo will have to take it off and install some shims under the bolts.if the starter is trying to turn and the lywheel isnt urning...then you have a locked up engine.

Apr 26, 2010 | 1999 Chevrolet Blazer

1 Answer

1995 plymouth voyager


check the conections on the starter & maybe remove the starter to check the solaniod & bushes if no good replce the sarter motor .
many thanks lee.

Jan 03, 2009 | 1995 Plymouth Voyager

2 Answers

Fuel problem?


Sounds like a clog somewhere.

Jul 21, 2008 | 1990 Ford F150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...