Question about 2000 Nissan Maxima

2 Answers

2008 nissan maxima crank sensor code keeps coming back and traction control sensor code what could cause this ? already replaced crank has no power ,put foot to floor and it takes for ever to get up to speed

Posted by on

  • Anonymous Mar 14, 2014

    it dies and the check engine light and traction control light on



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mas air meter could cause this problem.

Posted on Jul 30, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 726 Answers

I would be looking at the throttle assembly. it's all electronic (fly by wire, no cable). Souns to me like the throttle failed.

Posted on Jul 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Service engine soon

Check for any loose wire harness connection or bad contacts.

Aug 18, 2008 | 2002 Nissan Maxima

1 Answer

2004 nissan maxima engine code p0021&p1135. Intake valve timing control solenoid has already been replaced. What else could cause this?

I think I answered this a couple of weeks ago on a different Nissan. Both codes are saying the computer can not control valve timing on bank two.
There is a solenoid that uses engine oil flow to adjust valve timing.
If the sensors and solenoid are good, the problem could be lack of oil reaching the solenoid, or a problem with the wiring harness.

Jul 11, 2012 | 2004 Nissan Maxima

1 Answer

Just replaced camshaft sensor, bank 2, on a 2004 nissan maxima and now i have a loss of power, but the car runs smooth again. the same code keeps coming back though. what else can i do?

did you have a cam sensor stored?? and also which bank sensor did you replace?? bank 1 and bank 2 can be easily mixed up. well not mixed up, but bank 1 is by the firewall. bank 2 is at the radiator. you may have replaced bank 1 instead of bank 2. so when you remove the air box to replace sensors and you are lookin at the connectors, bank 1 is the one on the right side head. bank 2 is the left side head if you are looking at it from air box side. if you are looking at it from crank pulley side, bank 1 is on the left and bank 2 is on the right head. what code do you still have stored??

Oct 02, 2011 | 2004 Nissan Maxima

1 Answer

Twice now my 2004 Nissan Maxima has completely died as I was coming to a stop at an intersection. Both times it started back up again after about 10 minutes and then runs normal. I just don't want to...

I can guarantee your car keeps cutting off because there is a problem with your crank sensor. I have a '04 maxima SE and the day I paid my car off it did the exact same thing, it cut off then cranked back up a short while later and when I took it to the dealer there was a problem with the crank sensor. You might wanna check that and get it replaced's cheaper if u dont do it at the dealer tho

Jun 06, 2011 | 2004 Nissan Maxima

2 Answers

No start p0335

Hi, you should find your answer here:

Feb 06, 2010 | 1999 Nissan Maxima

2 Answers

P1320 trouble code plus

The P1320 code is essentially a coil primary voltage problem. This is traceable using a labscope or accurate DVOM and perhaps you can isolate one or two coils that still work but are close to failure...but there is a nissan service message recommending replacement of ALL coils with updated/improved models to prevent this type of failure. TCS/SLIP is traction control. Most likely you have a speed sensor issue. Be aware, some vehicles can falsely illuminate TCS because of low tire pressure in a single wheel.

Sep 09, 2009 | 2000 Nissan Maxima

Not finding what you are looking for?
2000 Nissan Maxima Logo

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides