Question about 1988 Buick Reatta

1 Answer

Replacing a part

How do i replace the rack-sw actr part number 26001765

Posted by on

  • Anonymous Apr 05, 2009

    im doing the same thing, first you have to take off the steering wheel and all that fun ****, then drop the steering column and take it off, you should be able to detach it at the firewall inside the car after that you can take teh casing and ignition switch off and then it exposes the part, i dono how to get that part off yet though

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Heres the best thing i have found on the net. its for a park avenue or something but its close enough after you get the steering wheel off

.http://buickperformance.com/tiltsteeringcolumnwobble.htm


Posted on Aug 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Foaming power steering fluid


Sounds like a bad replacement rack.. Did you buy a rebuilt rack? Look up the number for A1 Cardone.. They are in my openion the best rebuilders of rack and pinion.. You can talk to their tech team and they can answer your question.. I have never seen this problem.. i have had racks that the internal valves have went bad and lock up the rack and pump.. Post a comment here and let us know what you find so we will know too.

May 24, 2014 | Lincoln Cars & Trucks

1 Answer

Vt commodore rack boots


Vt commodore steering Rack boots always rip and tear,the racks always tend to leak from the internal seals.
So if this the case with yours I would recommend you just get a reconditioned steering rack and fit it but once the rack is replaced you will also need to do a wheel alignment.
steps to change rack .
1.raise vehicle on hoist
2.remove front wheels
3.remove tie rod end split pins
4.undo tie rod end nuts and inner nuts on rack ends
5.release tie rod end from hub.
6.centralise steering wheel and remove keys from ignition
7.count the number of turns on each side that tie rod come off and write down .
8.undo the 2 metal pipes that go into the rack feed and return lines and make sure u have container under the vehicle to collect old fluid.
9.undo the 13mm nut and bolt that mounts the rack to the steering colum shaft.
10.undo the 2 *19mm bolts and nuts that mount the rack to the crossmember.
11.gentle wiggle the rack and it will come away.
12.follow these steps in reverse when fitting new rack.,make sure you replace the oring seals .
13.you will need to get a wheel alignment done..

Feb 12, 2014 | Cars & Trucks

1 Answer

Nissan serena p1121


code p1121 refers to throttle position motor---malfunction===causes--throttle position motor
--- fix--replace the unit.

Dec 30, 2013 | Nissan Nissan Cars & Trucks

1 Answer

How to remove rack and pinion from 99 chrysler lhs


There are few help links showing exact accurate procedure to replace Rack and Pinion. Click the link below and follow the procedure:-----
Pinion Seal Replace on Dodge Dakota? http://howtobyme.blogspot.in/2012/04/pinion-seal-replace-on-dodge-dakota.html

-----------

How to Replace a Rear Pinion Seal.
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html
------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

----------
How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

-----------
How to replace power rack and pinion steering gear on Toyota cruiser? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-rack-and-pinion.html

----------


How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html


------------
Front Drive Pinion Seal Removal on Ford Explorer? http://repairhelpcenter.blogspot.in/2012/03/front-drive-pinion-seal-removal-on-ford.html

-------------
How to Replace Driveshaft, Pinion Flange & Seal?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-driveshaft-pinion-flange.html

------------


How to Replace Power Rack & Pinion Steering Gear On 2007 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


----------
How to Remove Power Rack & Pinion Steering Gear on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-rack-pinion.html

-----------

Power Rack & Pinion Steering Gear replacing details for Buick Park Avenue and Pontiac Bonneville

http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

-------------


How to Replace Power Rack & Pinion Steering Gear on Mercedes Benz Truck? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


---------
How to replace Power Rack & Pinion Steering Gear on Toyota 4Runner? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion_27.html

-----------

Power Rack & Pinion Steering Gear Replacing on Toyota Land Cruiser & Sequoia? http://schematicsdiagram.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

----------
Power Rack & Pinion Steering Gear Removal on Toyota RAV4? http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear-removal.html

----------
How to Replace Power Rack & Pinion Steering Gear on Toyota Sienna? http://technoanswers.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html

------------
These details will help.
Thanks.



Nov 23, 2012 | Cars & Trucks

1 Answer

Change the racket pion


To change the rack and pinion on your Monte Carlo you must first jack, or lift the car up off the ground, and remove the front wheels and tires.remove any plastic shrouds that block you from the bottom of the car.then you will need a Tie rod separator they make different types.You remove the tie rods from the front spindles.Trying not to damage the rubber on the tie rod ends that is what holds the grease inside for lubrication.then, if you look at the power steering hoses. these should come directly from the pump.loosen both the pressure, and the return hoses and remove from the rack. you will need a fairly large oil drain pan to catch any leaks that may happen. If you look where the steering shaft comes from the passenger compartment down to the rack. it must be removed from the rack, Note; center the steering wheel before removal of the new rack.Then the rack should have some mounting fasteners holding it to the chassis. when you replace this part,The new rack does not come with the tie rod ends that you had removed earlier from the outer ends of this part at the wheels. the old ones will need to be removed from the old rack and reinstalled back on the new rack.NOTE; to get these tie rod ends fairly close back to the same location,after you break them loose, you count the number of turns to remove these from the old rack. this has to be done to be able to get the front wheels back in close alignment and remember this count. because you replace these on the new rack and the count that you had coming off is the number of turns to put these back on the new rack. and tighten these down good.This rack may have to come out the sideways, or it may have to be got out by removing something that may be blocking removal. just look real close and see if there is a clear area it can come out.When you Install this new rack and pinion you mount the rack and install the hoses refill your power steering pump with fresh fluid. and check for any leaks. and before you install the hoses replace the o rings if there is any to make sure you have a good seal at your connections. then hook up your steering shaft to the new rack and check to see if you are still in alignment( steering wheel)after you hook up the tie rod ends and the new rack is mounted securely. double check your fluid level in the pump.you should get all the air out of the system, by cranking the engine and turn the steering wheel right and left all the way to the lock. ( or the stop) until you dont hear anymore noise from the system. it may take driving a little while before the noise is gone completely . Keep checking your pump fluid level while you are bleeding the air out of the system. and also keep your eyes on the areas where the hoses that you removed and replaced for any leaks that may be a problem.also when you install any fluid lines,always start them with care. make sure not to cross thread these lines. start them with your fingers first. then you should have the car alignment checked at a alignment shop, or a tire store. this is to make sure you have no alignment issues. and for a few days keep your fluid level checked.

Oct 30, 2011 | 1997 Chevrolet Monte Carlo

1 Answer

Spindle replacement


call round to junkyards, or get one on eBay or craigslist. lots of folks around who take cars apart and sell them piece by piece to supplement their disability checks. one should fit anywhere up to a 99SL or SW series. obviously the newer the better.

you are going to need some serious tools and mechanical knowledge to replace this, and it will need an alignment afterward. so i would suggest having a shop with an alignment rack do the work.

Feb 03, 2011 | 1993 Saturn SL2

1 Answer

How to replace Lincoln ls power steering pump sensor


Vaps Sensor--on steering rack
Pump Pressure Sw - in line next to pump

Mar 17, 2010 | 2000 Lincoln LS

1 Answer

My power steering is heavy after the dealer replaced the steering rack and steering pump. The service manager said this is normal due to Acura has redesigned the steering rack for 06 TL to prevent from...


This does not solve your problem, but perhaps power in numbers will help. I have had 2 steering racks replaced on my 2006 TL. Acura is not claiming any defects, but the steering is extremely difficult to turn. Hardly even feels like I have power steering. I'm upset because I had to pay for the 2nd rack just 14 months after the 1st one was replaced. I expected more from the Acura brand!

Nov 09, 2009 | 2006 Acura TL

1 Answer

1990 supra steering rack


There are seals that can be replaced, but if it is noticeably leaking, then you are likely going to need to replace the rack. It can be time consuming but it is well worth it. Replacement racks can be found either in other Supra's or you can find rebuilt ones online, those, however, usually require you to send yours in.

Dec 06, 2008 | 1990 Toyota Supra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...