Question about Dodge Dakota

Open Question

Removing dakota front bumper - Dakota Dodge Cars & Trucks

Posted by on

2 Suggested Answers

  • 2 Answers

SOURCE: removal of front bumper

The bumper is secured using four 13mm nuts.

a) Open the bonnet and look for one 13mm nut on the lower inside of each headlight.
b) Remove the towing eye covers on the lower section of the bumper and you will find one 13mm nut in each.

Hope this helps.
Shane

Posted on Apr 09, 2010

  • 10865 Answers

SOURCE: front bumper removal

all you have to do is unbolt it. if the nuts won't budge spray them with wd40 and wait over night for that product to loosen up the rust.

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the front bumper"?"


To remove you will have to use air tools as it cuts the time to minutes instead of hours. Remove front tires and unplug lights in fiberglass bumper. Then remove all the screws and remove fiberglass .bumper. I will supply and DIY email address so you can follow step by step. Subaru wrx sti remove bumper TUTORIAL DIY

May 06, 2014 | 2006 Subaru Legacy

1 Answer

How Do I Remove Front Bumper On A 98 Dodge Dokota


pop the hood under the grill you will see 2 bolts 1 to the left 1 to the right unscrew em and pull off the bumper

Aug 24, 2011 | 1998 Dodge Dakota

1 Answer

Jaguar x type 2004 front bumper


Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.

Becareful not to damage the fog lamp harness upon removal

Apr 08, 2010 | 2004 Jaguar X-Type

1 Answer

Can you help me dis-assemble my front bumper honda odyssey 1999 ?


Front
  1. Note the radio security code, then disconnect the negative battery cable.
  2. Remove the bolt from the lower part of the bumper just in front of the wheel opening, and remove the self-tapping screw from the rear most portion of the bumper at the forward portion of the front wheel well.
  3. On V6 Odyssey models, perform the following:
    • Remove the grille.
    • Remove the pins and clips from the lower front of the bumper.
  4. On 4-cylinder Odyssey models, remove the bolts from the left and right side lower brackets for the bumper at the ends of the lower air intake.
  5. Pull the ends of the bumper outward.
  6. Have an assistant help guide the bumper up and away from the vehicle.
  7. Installation is the reverse of the removal procedure.

Mar 06, 2010 | Honda Odyssey Cars & Trucks

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

1 Answer

The foot step ground skirt around the truck, the


Lower front valence, but Ford may call something else.

Feb 14, 2010 | 1995 Dodge Dakota

2 Answers

Need to know the firing order


For all Dodge V8 truck engines, the firing order is 1-8-4-3-6-5-7-2. For all Dodge V6 truck engines, the firing order is 1-6-5-4-3-2. For Dodge inline 6 cylinder engines, the firing order is For all Dodge 4 cylinder engines, the firing order is 1-3-4-2 All dodge distributors rotate clockwise.


look at your distributor cap while standing on the driver's side of the vehicle.
Start at number 1, which is labelled on the cap, and go
clockwise

Good Luck

Oct 28, 2009 | 1998 Dodge Dakota

1 Answer

Need help with the wiring diagram for my 92 Dakota, has not brake lights or blinkers


www.wiring-diagram.com
You can get any wiring diagram for any vehicle. It will cost about $12 and it's well worth it. It will give you the complete diagram bumper to bumper.

Apr 29, 2009 | 1998 Dodge Dakota

1 Answer

Replace the face skid in the front bumper


remove front bumper and it should be clear what holding the face skid in place

Sep 29, 2008 | 2008 Honda Pilot

1 Answer

1998 Dodge Dakota engine compartment/chassis assembly dwgs.


hello , you could take a look at our products section , our look at the related links , thank you for using fixya.

Jun 24, 2008 | 1998 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

743 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...