Question about Geo Prizm

1 Answer

Satbelt does not retract, i can still buckle up, but when i unbuckle the seatbelt just stays in place, and dangle...doesnt glide back

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Hello does it try to go back if you play with it? if so you can remove the trim panel and lube the seat belt mech. the system get dust and dirt in the spring the operates the seat belt try to lube it it may work hope this helps you thanks

workitover

Posted on Jul 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I stop the seatbelt noise to stop after buckling up?


If the chime doesn't stop you will have a problem with the floor mounted portion of the seat belt. You can spray some WD 40 in the slot and buckle/unbuckle several times to see if the problem will correct itself. If not the chime module can be removed from under the dash once you follow the noise and locate it

Jul 10, 2015 | Cars & Trucks

1 Answer

2005 town and country touring i want to disconnect the seatbelt warning light and chime?


1. Turn the ignition switch to the off position and buckle the seat belt
2. Turn the ignition switch to run (engine does not need to be running), wait for the seat belt light to turn off.
3. Within 60 seconds, unbuckle and rebuckle the drivers seat belt at least 3 times, ending with the seat belt buckled.
4. Turn the ignition key to the off position. A single chime will sound to signify that you have successfully completed the programming.

It can be reactivated by repeating these steps.

The alert will be deactivated but the warning light will continue to stay on will the belt is unfastened.

Feb 13, 2013 | 2005 Chrysler Town & Country

1 Answer

Seat bealt light on but my seat bealt is working


Reset the connector under the Pax. side front seat. This has to be done with the ignition off. 1. Buckle the seatbelt. 2. Reset connection. 3. Unbuckle the seatbelt. 4. Turn ignition switch on and watch the light reset to off. 5. If light continues off, go to the Driver side and repeat the procedure. My problem was fixed after doing procedure 1. hope that helps.

Jan 19, 2013 | 2002 Ford Escape

1 Answer

On the dashboard a large red seatbelt symbol appears with the word pass underneath, also a large letter (i) appears next to the gauge


Did you transport a box or heavy object on the passenger seat?
The weight sensor (part of air bag system) detect a heavy object on the passenger seat.


With key on and engine running,clear the passenger seat ////// buckle then un-unbuckle to clear warning.

Also check the weight sensor and buckle connector.
Car wash clean can accident disconnect (or damage) this connector during vacuum.
======== Also inspect the pass. buckle opening for dirt.

Jul 28, 2011 | 2004 Saab 9-3

1 Answer

How does the rear seat center seat belt work???


The rear seatbelt of the forester was a bit of a puzzle for me as well when we first got ours. The buckle is really in two parts. The first part anchors the strap, and the second part secures the occupant.

Check if your belt is fully retracted, look in the inertia reel housing at the roof in the boot of the vehicle. Remove it passing the end through the 'loop' in the backrest Make sure that you have the two buckle parts I referred to earlier. There should be an odd looking buckle fixed at the end of the belt, and the more familiar buckle that slides up and down the belt. The end buckle goes into the receptacle vertically below the loop between the centre and window passenger and achors the belt in place. This buckle should not be normally released once used regularly. Once the centre passenger is in place, use the sliding buckle as you would for any other seatbelt and fasten on the receptacle on the other side to secure.

Use same procedure for fixing a car seat or booster, etc.

Sep 24, 2010 | 2002 Subaru Forester

2 Answers

Seat belt buzzer , how do you turn it off.


Hope this helps ya.. Cobra.. :-)

Belt-Minder® Deactivating/Activating Vehicles Built After 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place the transmission range selector lever in PARK.
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver and passenger safety belts.
Deactivating/Activating
  1. Turn the ignition switch to the RUN position. (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 minute).
  1. NOTE: Step 3 must be completed within 50 seconds after the safety belt warning lamp turns off or the procedure must be repeated.
    For the seating position being disabled, buckle then unbuckle the safety belt 9 times, ending with the safety belt unbuckled.
  1. NOTE: After Step 3, the restraint system warning indicator lamp turns on for 3 seconds.
    Within 10 seconds of the safety belt warning indicator turning on, buckle then unbuckle the safety belt.
  1. The beltminder activation or deactivation is confirmed by the following sequences:
    • If the beltminder is enabled, this procedure will disable the beltminder for that specific seating position. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds to confirm that the deactivation procedure was successful.
    • If the beltminder is disabled, this procedure will enable the beltminder for the specific seating postion. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds followed by a second series of 4 flashes per second for 3 seconds to confirm that the activation procedure was successful.
  1. After confirmation, the deactivation/activation procedure is complete.
Vehicles Built Prior To 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission).
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver safety belt.
  1. Place the parklamps/headlamps switch in the OFF position. (if vehicle is equipped with Autolamps, this will not affect the procedure.)
Deactivating/Activating
  1. Turn the ignition switch to the RUN position (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 to 2 minutes).
  1. NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be repeated.
    Buckle then unbuckle the safety belt 3 times, ending with the safety belt unbuckled. This portion of the procedure can be done before or during belt minder warning activation.
  1. Turn the parklamps/headlamps on then off.
  1. Buckle then unbuckle the safety belt 3 times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for 3 seconds.
  1. Within 7 seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled and disable the belt minder if enabled.
  1. The following sequence of events confirm the belt mnider is enabled:
    • flashing of the safety belt warning belt lamp 4 times per second for 3 seconds
    • 3 seconds with the safety belt lamp off
    • flashing the safety belt lamp 4 times per second for 3 seconds again
  1. The safety belt lamp flashing 4 times per second for 3 seconds provides confirmation of belt minder disabled.
  1. After confirmation, the deactivation/activation procedure is complete.


Jun 15, 2010 | 2004 Ford F150

2 Answers

2005 jaguar type-s. How can i disable the belt minder. The seatbelt alrm is making me crazy


To enable or disable the seat belt warning chime on your 2005 Jaguar Type S

1. Ensure the front passenger seat is unoccupied.

NOTE:

Steps two to five must be completed within 60 seconds.

2. Turn the ignition to the RUN position (do not start the engine).

3. Buckle the driver safety belt buckle and wait until the seat belt warning lamp extinguishes.

4. Unbuckle the driver safety belt buckle and wait until the seat belt warning lamp illuminates.

5. Repeat Steps three and four a further eight times.

6. When the driver safety belt buckle is unbuckled for the ninth time a single chime will be heard. The single chime is acknowledgement that the beltminder feature has been disabled.

The beltminder feature will be disabled until the above process (Steps one to six) are repeated. Upon repeating the process the beltminder feature will be reactivated

Apr 25, 2010 | Jaguar S-Type Cars & Trucks

1 Answer

How to disable seatbelt alarm on 2003 F-150?


There is a procedure in the owners manual on page 110.

BeltMinder activation and deactivation procedure
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.)
2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.)
• Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled
• After step 5 the safety belt warning light will be turned on for three seconds.
6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.
• This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.
7. Confirmation of disabling BeltMinder is provided by the safety belt warning light flashing four times per second for three seconds.
8. Confirmation of enabling BeltMinder is provided by:
• The safety belt warning light flashing four times per second for three seconds.
• Followed by three seconds with the safety belt warning light off.
• Once again, the safety belt warning light will flash four times per second for three seconds.
9. After receiving confirmation, the deactivation/activation procedure is complete.

If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Dec 20, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Audible seatbelt warning keeps on sounding on my 2005 f150 ford truck


From the F-150 Forums, since I just bought one and this worked!

This is straight from my 2009 f150 owners guide

Preperation
1. the parking brake is set
2. truck in park
3. ignition switch is in off position
4. both seat belts are unbuckled

Disable Belt-Minder
1. turn the ignition switch to the on position, DO NOT START THE ENGINE.
2. wait until the safety belt warning light turns off. (approximately 1 minute).
* step 3 must be completed within 50 secs after the safety belt warning light turns off.
3. buckle then unbuckle the seat belt nine times, ending in the seat belt unbuckled.
* after step 3 the restraint warning light, (airbag light) will turn on for three (3) seconds.
4. within approximately seven (7) seconds of the light turning off, buckle then unbuckle the safety belt.
* the restraint system warning light will flash four, (4) times per second for 3 seconds for confirmation

you can do this for the passenger side also!!!


*NOTE
in step 3. after three times buckling and unbuckling the restraint warning light lit up in my truck. SO I WENT TO THE NEXT STEP, (STEP 4). waited 3 seconds and i buckled and unbuckled.

in the buckle /unbuckle procedure do it some what slowly and watch for the light. it may not take 9 times.
__________________

May 08, 2009 | 2005 Ford F-150

2 Answers

I need a copy of teh manual for my 2004 Ford Explorer manual.


Wear your safety belt, or simply unplug the harness located at the seatbelt receptacle.

Jan 13, 2009 | 2004 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

223 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...