Question about Honda Odyssey

1 Answer

Can not remove tail light housing to replace light bulb

Posted by on

1 Answer

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the tail light fixture to replace brake bulb?


Four of them ?
Remove the tail lamp housing to body screws. Carefully slide the tail lamp housing rearward away from vehicle. Disconnect the tail lamp housing electrical connector. Remove the tail lamp housing from the vehicle.

Mar 22, 2015 | 2002 Saturn VUE

1 Answer

Change a turn signal bulb on a 2006 dodge grand caravan


The rear remove two push in pins remove tail light housing replace bulb. Front remove screws holding head light housing replace bulb

Feb 28, 2015 | 2006 Dodge Grand Caravan

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

How do I remove the tail light to get to the brake light bulb to replace it


No Product

Remove the Lamp Housing
from the body

Been like that for 30 years

Aug 25, 2014 | Cars & Trucks

1 Answer

I have a 1996 Volkswagon Cabrio. I was notified that the back right tail light is burnt out. Can you assist? I would like to try to fix it myself.


If this is helpful, please vote for my answer:
1 Open the trunk and pull up the carpet in the trunk. 2 Remove the screw bolts that hold the trim piece to the back of both of the tail light housings. 3 Remove the trim backings to expose the tail lights. 4 Remove the electrical plug running to the bulb's ballast. Squeeze the top of the connector's release tab and remove the plug. 5 Turn the bulb counterclockwise to remove it from the housing. 6 Remove the screw bolts on the inside of the trunk that hold the tail light housing to the body. 7 Pull the tail light housing off. 8 Replace bulb with same

Mar 07, 2011 | 1996 Volkswagen Cabrio

1 Answer

Is there a trick to getting to the rear turn signal on a 2003 ford focus hatchback. I had removed the screw to the lens cover but I still cannot gain access to the turn signal bulb to replace it.


Replacing tail/brake/backup lights and turn signal bulbs (coupe)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. From inside the luggage

compartment remove the wing nut

of the rear light assembly cover.

3. Using a Phillips screw driver

remove the screw. The lamp is still

retained by a spring loaded clip.

Remove by gently pulling out the

light housing.

4. Turn the bulb socket counterclockwise as far as possible and pull it

out.

5. Pull the bulb straight out of the socket.

Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (sedan)

1. Make sure the headlamp control

is in the OFF position and then

open the trunk.

2. From inside the luggage

compartment remove the three wing

nuts of the light housing.

3. Gently pull the light housing to

the outside.

4. Turn the bulb socket

counterclockwise and pull it out.

5. Pull the bulb straight out of the socket.
Install in reverse order.

Replacing tail/brake/backup lights and turn signal bulbs (wagon)

1. Make sure the headlamp control

is in the OFF position and then

open the hatchback.

2. Using a screw driver remove the

fixings and trim from the body.

3. Remove the socket from the lamp

assembly

4. Pull the bulb straight out of the

socket.
Install in reverse order.


Hope this helps.

Zeppelinx12

Mar 03, 2011 | 2003 Ford Focus

1 Answer

How to replace tail light bulb


Unplug the wires from the housing (remeber where they go markignt hem if need be). Then you will eb able to pull the light bulb housing off the light housing. the bulb will then pull or twist out of this hosuing(sure is alot of housings :) ). from there its just putting it all back togther

May 15, 2009 | 2005 Honda Odyssey

1 Answer

Replace the tail light bulbs in 2004 infiniti g 35 coup


tail light bulbs are replaced by removing the tail light housings. The housings are accessed by removing the nuts, the nuts are secured behind the inner trunk liner inside the trunk. Remove fasteners holding liner in place, remove 3 nuts for each housing(i believe it's 3 nuts if my memory serves me right), remove housing and replace bulbs

Jan 13, 2009 | 2004 Infiniti G35 Sport Coupe

1 Answer

Tail light blinker replacement


Laura E;

Most tail light housings use the same approach. The bulb is removed from the housing by twisting
the back of the bulf where the wires are. Usually the bulb itself has a rubber back and turning it about a quarter turn counterclockwise (remember lefty=loosey; righty = tighty) will release the bulb it from the taillight housing. Take the bulb with you when you go for a replacement to be sure you get the right one.
The bulb will only fit one way into its socket and the socket will only fit one way into the housing.

Good luck ,

Loringh

Oct 14, 2008 | 1994 Ford Thunderbird

2 Answers

Replace tail light bulb


open hatch, look for two screws, remove , push tail light gently back and forth to release from clips pull light assembly out , twist bulb socket to remove from housing, replace bulb.

Aug 20, 2008 | 2005 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

71694 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7031 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...