Question about 1998 Chevrolet Venture Cargo

1 Answer

Cannot find my vehicle speed sensor - 1998 Chevrolet Venture Cargo

Posted by on

1 Answer

Were is the speeddometer sensor 98 venture

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0501 code?


P0501 - Vehicle Speed Sensor (G22): Implausible Signal Possible Causes
  • Wiring/Connectors from/to Vehicle Speed Sensor (G22) faulty
  • Wiring/Connectors from Transmission Control Module (J217) to Engine Control Module faulty
  • Vehicle Speed Sensor (G22) faulty
  • Malfunctioning Left Front wheel speed sensor (in vehicles that don't use a physical G22 sensor)
Possible Solutions
  • Check Wiring/Connectors from/to Vehicle Speed Sensor (G22)
  • Check Wiring/Connectors from Transmission Control Module (J217) to Engine Control Module
  • Check Vehicle Speed Sensor (G22)
  • Check ABS Brakes for faults and diagnose malfunctioning Left Front wheel speed sensor if applicable

Category:

Mar 10, 2016 | 1996 Audi A4

1 Answer

What parts have to be removed to change output speedsensor on 97 sebring convertible jxi?


Hi Nicholas, Im AL the owner of Big As Auto Repair.

FRONT WHEEL SPEED SENSOR

REMOVE
  1. Raise vehicle on jack stands or centered on a frame contact type hoist. See Hoisting in the Lubrication and Maintenance section of this manual, for the required lifting procedure to be used for this vehicle.
  2. Remove the tire and wheel assembly from the vehicle.
  3. Remove the speed sensor cable routing bracket Speed Sensor Cable Routing Brackets from the steering knuckle. Remove the wiring harness sealing grommet retainer and speed sensor routing bracket from the inner fender.
  4. Remove speed sensor sealing grommet from the inner fender Wheel Speed Sensor Connection To Vehicle Wiring Harness Then unplug the speed sensor cable from the vehicle wiring harness Wheel Speed Sensor Connection To Vehicle Wiring Harness
  5. Remove bolt Speed Sensor Head Attachment To Steering Knuckle attaching the speed sensor head to the steering knuckle. Then remove speed sensor head from steering knuckle. CAUTION: If speed sensor head locating pin has seized to the steering knuckle, do not attempt to remove speed sensor head by grasping with pliers and turning. This will damage the speed sensor head. Use only the following procedure.
  6. If speed sensor head can not be removed from steering knuckle by hand, the locating pin on the speed sensor head has seized to the steering knuckle do to corrosion. Remove speed sensor head from steering knuckle using the following procedure. Remove disc brake caliper from steering knuckle, and remove brake rotor from hub/bearing assembly. Then insert a pin punch through hole in front steering knuckle Speed Sensor Head Removal From Steering Knuckle and tap speed sensor head locating pin out of steering knuckle.
Hope this helps and please visit my auto-repair-website at:
http://www.bigasautorepair.com/

Oct 08, 2015 | Cars & Trucks

1 Answer

Where is the vehicle speed sensor located in a 1999 Buick century


Vehicle Speed Sensor Replacement
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. Remove the right front tire and wheel. Refer to Tire and Wheel Removal and Installation in Tires and Wheels. Remove the right engine splash shield. Refer to Engine Splash Shield Replacement in Body Front End.
Remove the vehicle speed sensor wiring harness connector.
Remove the vehicle speed sensor bolt (9). Remove the vehicle speed sensor (10) from the extension case.
Remove the O-ring (11) from the vehicle speed sensor (10).
Vehicle Speed Sensor (VSS)
Lower right side of the engine compartment, on the transaxle

Sep 05, 2015 | Buick Cars & Trucks

1 Answer

Subaru 97 speed sensor trouble code p0500 not passing admissions.. what part to I buy and where is the sensor located?


There are actually two Vehicle Speed Sensors (VSS). I'm going to assume you have a 2.5 liter engine and an automatic transmission.

The Vehicle Speed Sensor 1 (output shaft rotation sensor) is mounted to the extension case (from the outside of the case). The sensor outputs a pulse signal which is transmitted to the TCM where it is converted to vehicle speed.


The transfer clutch drum is connected directly to the rear wheel driving propeller shaft. Vehicle speed sensor 1 on the AWD model detects rear-wheel speed.

zjlimited_382.gif

Vehicle Speed Sensor 2 provides vehicle road speed information to the ECM. The ECM uses this data to properly determine ignition and fuel delivery curves. The sensor consists of a reed switch and magnetic rotor turned by the speedometer cable.


One rotation of the magnetic rotor opens and closes the reed switch four times, producing a digital signal which is converted to vehicle speed by the ECM. The sensor operates whenever the vehicle is moving with ignition ON. As the transmission rotates, the speed sensor sends a pulsed on/off signal to the ECM.


zjlimited_383.gif

The speedometer uses VSS 2 for it's signal.

Hope this helps (remember to rate this answer).

May 24, 2011 | 1997 Subaru Outback

1 Answer

Can you tell me where vechile speed sencor 'A' is on my focus st the fault code is P0500


P0500 Vehicle Speed Sensor "A"
P0501 Vehicle Speed Sensor "A" Range/Performance
P0502 Vehicle Speed Sensor "A" Circuit Low Input
P0503 Vehicle Speed Sensor "A" Intermittent/Erratic/High
Vehicle Speed Sensor Removal & Installation Automatic Transmission To Remove:
  1. Remove or disconnect the following:
    • Output shaft speed (OSS) sensor electrical connector.
    • Bolt and OSS sensor
To Install:
  1. Apply a light coat of petroleum jelly to the O-ring before installation
  2. Install or connect the following:
    • OSS sensor torque bolt to 89 in-lbs (10 Nm)
    • OSS sensor electrical connector
Manual Transmission To Remove:
  1. Remove or disconnect the following:
    • Vehicle Speed Sensor (VSS) electrical connector.
    • Retaining pin.
    • VSS.
To Install:
  1. Install or connect the following:
    • VSS.
    • Retaining pin.
    • VSS connector.
---
The VSS is on the transmission near the output shaft. It will not be a wheel speed sensor on the hub.

Good luck on this repair, tommy.

Nov 06, 2010 | 2006 Ford Focus

1 Answer

Speedometer is reading incorrectly. need to replace the speed sensor on the transmission or some where else.


Yes, I would start at the speed sensor on the transmission called the VSS (Vehicle Speed Sensor).

Also, are the tires the right size for the vehicle as indicated by the placard on the inside of the door?

The following is the example for some GMC Envoys (I had to guess on the engine size):

Vehicle Speed Sensor Removal & Installation To Remove:
  1. Disconnect the vehicle speed sensor connector. Vehicle speed sensor (A), Retaining bolt (B), O-ring (C) vsssensor.gif

  2. Detach the vehicle speed sensor from the transfer case.
  3. Remove the o-ring from the vehicle speed sensor.
To Install:
  1. Apply transmission fluid to the o-ring.
  2. Install the o-ring onto the vehicle speed sensor.
  3. Attach the vehicle speed sensor to the transfer case. Torque the bolt to 97 in-lb (11 Nm).
  4. Connect the vehicle speed sensor connector.
prev.gif next.gif

Oct 08, 2010 | 2004 GMC Envoy

2 Answers

Where is speed senor on a Hyundai Sonatas


Hyundai VSS locations:
On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1996-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

On 1999-2003 vehicles, the vehicle speed sensor is built into the speedometer. On 2004-2005 vehicles, the vehicle speed sensor is attached to the output shaft of the transaxle.

Hope helps (remember rated this).

Jul 14, 2010 | Hyundai Motor 2004 Sonata

1 Answer

Where is the speed sensor located?


The vehicle speed sensor is located below the air cleaner assembly, it is held in with one bolt (I believe 10mm):
  1. Remove the bolt and vehicle speed sensor assembly.
  2. Remove the clip and speedometer driven gear from vehicle speed sensor.
  3. Remove the O-ring from vehicle speed sensor
  4. Coat a new O-ring with ATF and install it to the vehicle speed sensor.
  5. Install the speedometer driven gear to the vehicle speed sensor and clip.
  6. Install the vehicle speed sensor assembly and torque the bolts. Torque: 16 Nm (160 kgf-cm, 12 ft. lbs.)

Mar 23, 2010 | 1999 Toyota Camry

2 Answers

Speedometer stop working where's the cable?


Your vehicle does not have a traditional speedometer cable. Instead it uses a VSS (Vehicle Speed Sensor) to read speed of the vehicle below is a short test to help you determine if it is the VSS that has failed.

SPEEDOMETER VEHICLE SPEED SENSOR TEST

1. Press and release trip odometer button until function number 6 appears in display window.

2. Turn a front wheel and observe display (pulses are added to number in display. Check impulse signal for speedometer vehicle speed sensor. If 7 pulses are generated per wheel revolution, vehicle speed sensor is okay.

3. If specified number of pulses are not generated, check for open in wiring harness between speed sensor and instrument cluster. Repair wiring harness if necessary. If wiring harness is okay, replace speedometer vehicle speed sensor.

Jan 21, 2010 | 1996 Volkswagen Passat

1 Answer

Speed sensor on 2000 ford f150 4x4 triton 4.6


if this helps, please rate as fixya. thanks.

Vehicle Speed Sensor The vehicle speed sensor (VSS) (Figure 43) is a variable reluctance or Hall-effect sensor that generates a waveform with a frequency that is proportional to the speed of the vehicle. If the vehicle is moving at a relatively low velocity, the sensor produces a signal with a low frequency. As the vehicle velocity increases, the sensor generates a signal with a higher frequency. The PCM uses the frequency signal generated by the VSS (and other inputs) to control such parameters as fuel injection, ignition control, transmission/transaxle shift scheduling and torque converter clutch scheduling.


66290d2.gif
For the 4R70W trans vehicles

Vehicle Speed Sensor (VSS)

The vehicle speed sensor (VSS) is model dependent. Possible sources of vehicle speed input are, anti-lock brake sensor (ABS), a gear-driven vehicle speed sensor (VSS), or the transmission output shaft speed (OSS) sensor. On 4x4 applications with a manual shift transfer case, the transfer case speed sensor is the source of vehicle speed. The VSS signal is either an AC signal whose frequency changes with vehicle speed, or an SCP data message depending on the source. Some vehicles have both. The vehicle speed signal is an input to various vehicle sub-systems such as the powertrain control module (PCM), instrument cluster (speedometer and odometer), speed control systems, etc. The vehicle speed source must be operational to enter output state control mode for diagnostics.

If you have a 4R100 trans, it is different.

Mar 12, 2009 | 2000 Ford F150 Flareside SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...