Question about 1994 Mazda 2WD B Series Pickup

1 Answer

Torque on 1994 Mazda pick up

What is the torque on the cylinder head bolts, exhaust manifold bolts, and the intake bolts on a 1994 Mazda pick up?

Posted by on

  • twinkle monk May 11, 2010

    is it a six cylinder or four/

  • Anonymous Mar 27, 2014

    need torque settings

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 30 Answers

If its a four cylinder(lets hope)the specs are 80-90ft.lbs torque.if its a six cylinder it is 14ft.lbs torqueat 90 degree intervals then repeat until correct torque has been reached.bad news is you can not use the same bolts on the six cylinder engine.have to be new to keep from breaking them

Posted on Mar 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque Settings For Mazda WL Turbo Engine


TORQUE SPECIFICATIONS all readings in ft. lbs.

This for 2000 model I do not know the yuear of your car.

Year Engine Displacement Liters Engine VIN Cylinder Head Bolts Main Bearing Bolts Rod Brearing Bolts Crankshaft Damper Bolts Flywheel Bolts Manifold Intake Exhaust Spark Plugs Oil Pan Drain Plug 2000 2.5 C ? ? ? 103-133 54-64 3.0 U ? 60 26 107 54-64 4.0 X ? 66-77 19-24 ? 59


Apr 11, 2016 | Mazda Cars & Trucks

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

Engine torque settings


Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs
  • The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.


Other Torque Specs
  • The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque

Nov 07, 2012 | 1994 Toyota Corolla

1 Answer

Torque setting for a 1998 ford taurus 3.0 intake manifold


TORQUE SPECIFICATIONSDescriptionNmLb-FtLb-InEngine Air Cleaner Tube Clamps1.6-2.2-14-19Engine Control Sensor Wiring Through Bolts2.5-3.5-23-30Generator to Bracket Bolt3727-Generator to Cylinder Head Bolt4835-Generator Brace to Upper Intake Manifold Bolts and Nut12-209-14-Intake Manifold Support to Throttle Body8-12-71-106Intake Manifold Support to RH Cylinder Head40-5530-40-Degas Tube to Upper Intake Manifold Bolts8-12-71-106Camshaft Sprocket to Camshaft Bolt50-7037-51-Camshaft Thrust Plate Bolt10-88Coil and Bracket to Cylinder Head Bolt40-5530-40-Connecting Rod Nut31-3923-28-Crankshaft Damper to Crankshaft Bolt125-16593-121-Crankshaft Pulley to Damper (4 Bolts)40-6030-44-Cylinder Head Retaining Bolt(1)(1)-Accelerator Cable Shield Bolts1.4-13Camshaft Position Sensor Housing Retaining Bolt2417-EGR Tube Connector to Exhaust Manifold40-4730-34-EGR Valve to Upper Intake Manifold Bolt20-3015-22-EGR Tube to EGR Valve and Exhaust Manifold35-6526-47-Exhaust Manifold Bolt/Stud20-2515-18-Flywheel to Crankshaft Bolt73-8754-64-Fuel Injection Supply Manifold to Intake Manifold8-12-71-106Throttle Cable Bracket1713-Dual Converter Y Pipe to Exhaust Manifolds34-4725-34-Crankshaft Position Sensor Bolts5-7-45-61Intake Manifold to Cylinder Head Bolt (5)(2)(2)-Main Bearing Cap Bolt75-8556-62-Oil Drain Plug11-169-11-Oil Filter Insert to Cylinder Block27-4020-29-Oil Filter to Oil Filter Adapter(3)(3)-Oil Galley and Cooling Jacket Plugs2014-Oil Level Indicator Tube to Exhaust Manifold Nut16-2012-14-Engine to Transaxle/Torque Converter Assembly Bolts40-6030-44-Torque Converter Nuts27-4620-33-Transmission Range Sensor Nut16-2212-16-Front Sub-Frame-to-Body Bolts77-10357-75-Oil Pressure Sensor16-2212-16-Oil Pump to Cylinder Block Bolt40-5530-40-Power Steering Bracket to Cylinder Head Bolt40-5530-40-Valve Cover to Cylinder Head Bolts/Studs (5)10-14-89-123Right Exhaust Manifold Heat Shield Retaining Bolts8-12-71-106Rocker Arm Seat to Cylinder Head Bolt(4)(4)-Water Outlet Connection to Intake Manifold Bolt10-14-89-123Upper Intake Manifold to Lower Intake Manifold Bolt/Stud20-3015-22-Engine Front Cover to Cylinder Block Bolt (No. 1-10)2518-Engine Front Cover to Cylinder Block Bolt (No. 11-15)10-88Water Pump Pulley to Hub (4 Bolts)20-3015-22-Water Pump to Front Cover Bolt8-12-71-106Wiring Retainer Bracket Nut20-3015-22-Valve Tappet Guide Plate to Cylinder Block10-14-89-123Ignition Coil Bracket40-5530-40-Oil Pan to Cylinder Block Bolt10-14-89-123Water Bypass Tube Nut20-3015-22-Crankshaft Pulley Bolts40-5530-40-


  1. Tighten in four steps (refer to illustration in Cylinder Head Installation for tightening sequence):
    • Tighten in sequence to 70-90 Nm (52-66 Lb-Ft)
    • Then back off all bolts 360 degrees
    • Tighten in sequence to 45-55 Nm (34-40 Lb-Ft)
    • Tighten in sequence to 85-99 Nm (63-73 Lb-Ft)
  2. Tighten in two steps
    • 20-30 Nm (15-22 Lb-Ft)
    • 26-32 Nm (20-23 Lb-Ft)
  3. Advance 3/4 to 1 turn after gasket contacts sealing surface or tighten to 13-15 Nm (10-11 Lb-Ft).
  4. Tighten in two steps:
    • 7-15 Nm (6-11 Lb-Ft)
    • 26-38 Nm (20-28 Lb-Ft)
  5. Refer to illustration in the Cylinder Head Installation procedure for tightening sequence.

Jan 10, 2012 | 1998 Ford Taurus

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    2 Answers

    Torque specification on a 2003 alero cylinder heads 3.4 liter


    3.4L Engine To Remove:
    1. Remove the lower intake manifold.
    2. Remove the exhaust crossover pipe.
    3. If removing the right cylinder head, remove the catalytic converter from exhaust manifold.
    4. If removing the left cylinder head, remove the engine oil dipstick and tube.
    5. Remove the rocker arms and pushrods.
    6. Remove and discard the cylinder head bolts.
    7. Remove the cylinder head.
    8. Clean the mating surfaces on the following items:
      • Cylinder head
      • Cylinder block
      • Intake manifold
    9. Clean the cylinder block bolt threads.
    NOTE: During disassembly, keep the valve train components together for proper location during assembly.
    To Install:
    NOTE: Coat the cylinder head bolt threads using thread sealer.
    1. If removed, install the following components:
      • Exhaust manifold
      • Accessory studs
      • Spark plugs
    2. Place the cylinder head gasket in position over the dowel pins. Ensure that the THIS SIDE UP note is showing.
    3. Install the cylinder head. Cylinder head torque sequence ’99-‘00 gmpc_v6_14.gif

      Cylinder head torque sequence ’01-05 gm-03-34-682.gif

    4. Install the new cylinder head bolts.
      • Tighten the cylinder head bolts a first pass to 44 ft lb (60 Nm).
    5. Tighten the cylinder head bolts in sequence an additional 95 degrees.
    6. Install the intake gasket.
    7. Install the pushrods and rocker arms.
    8. Raise and support the vehicle.
    9. Install the catalytic converter and dipstick tube and indicator if removed.
    10. Lower the vehicle.
    11. Install the exhaust crossover pipe.
    12. Install the intake manifolds.
    13. Connect negative battery cable.
    14. Fill the cooling system.

    Jul 03, 2010 | 2003 Oldsmobile Alero

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    3 Answers

    Need head bolt, intake manifold, and exhaust torque specs


    Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

    Mar 06, 2010 | GMC Suburban Cars & Trucks

    Not finding what you are looking for?
    Cars & Trucks Logo

    544 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...