Question about 1995 Ford Ranger Supercab

1 Answer

Ob2 code p14444

I have a 95 ranger with a code of p14444 what do I need to do to fix the problem

Posted by on

  • bigred495 Jul 24, 2008

    Ok thanks for the information, now what to I fix to make this problem go away replace the control valve and where is it located thanks



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 397 Answers

P1444 Purge Flow Sensor circuit Input Low
Evaporative emmision control system control valve malfunction
You can find all the fault codes here:

Posted on Jul 24, 2008

  • Richard Finch Jul 24, 2008

    You need to buy a manual on this truck.

    In the UK I would be happy to have a go at it, but in the States I know the emissions regulations from State to State cab vary enormously. It's possible that it is only out of adjustment, this valve controls excess fuel back to the tank from the fuel rails, it could be dirty, it could be malfunctioning. If I were you I would get some local advise on it before buying a manual and pulling it apart.

    Is there an Autozone or something near you? I am sure they could tell you the local laws and if you can do this job yourself.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to fix engine power loss and no heat from heater

Get an ob2 code reader and read the codes!

Dec 06, 2014 | 2002 Ford Expedition

1 Answer

2002 Sante Fe OB2 scan result showed P0740 code and other codes solenoids A B C D also showed on the scan how do i fix the tansmission issue.

Transmission Shop

You knew where to start

Can go to your regular shop, if you like,
or waste money at a dealer

Nov 03, 2014 | Cars & Trucks

2 Answers

Turn off emissions warning light

You don't. You have to get it "coded" to find out what the error is first.

Sep 29, 2014 | 2004 Honda Accord

1 Answer

99 ranger 4.0 ohv 4x4 No Spark to plugs

The Computer sends signal to the coils which sends spark to the plugs. u need to check for a code with a ob2 reader since these parts can be very expensive. and very time consuming GL

Aug 08, 2014 | 1999 Ford Ranger SuperCab

1 Answer

'96 Ranger start up

i had a ranger same problem i replace everything i could think of except for the crank shaft postioning sensor! a ob2 meter was hook up to the computer in the truck it sent a code and i was able have it repaired. that was the second time, the first time my battery got disconnected, so the computers code got wiped out i didnt no two months later i put it back in the shop they got the code that time! good luck

Jan 09, 2013 | Ford Ranger Cars & Trucks

1 Answer

Subaru code 851

Hi Mr. Wilde, if you were given a code from your OB2 Senor, you can take that code to Pep Boys or Auto Zone who I prefer. Auto Zone will take the code and explain to you what it means. They can also recheck your car or truck if they have time and the correct hook up to check the OB2 sensor or the jack that is located under the dash board. They can then print out for you the codes and the reason why the code has came up and how to fix your problem. It never matters how old or how many miles is on your vehicle. Let me know how that worked for you.

Jul 06, 2012 | 2005 Subaru Outback

1 Answer

While im driving to work lights just pop out in my dash board i just got new spark plug and did transmession fluids. and while im driving up the hill, ive notice that its got hardto go up.

have codes pulled for free from auto parts store they will tell you what codes mean they have a ob2 they plug it into your harness tells them why the lights on dash are comeing on then you can fix it need any more help just respond back to me

Dec 11, 2010 | 2000 Dodge Durango

1 Answer

Check engine light is on. How do I fix this problem?

you will need a OB2 code reader. plug in turn key on press read or link. it will give dtc trouble code look up code which willput you in the neighborhood of problem. when problem is solved reconnect code reader peress erase code . If going for reinspection make sure you turn ignition on and off close to 100 times to simulate trips if it doesn;t come back on problem solved. if you dont simulate that cycle and go for reinspection it will come up not ready. Hope this helps.

Nov 12, 2008 | 1997 Acura TL Series

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5613 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides