Question about 2000 Chevrolet Blazer

3 Answers

2000 s10 blazer 4x4

Where is the transfer case shifter module located?

Posted by on

  • tittlerat2 Feb 26, 2009

    jamer1223-titttlerat2 here i had same problem!!! truck shifted into 4x4 low an it would'nt disengage. i poped open the kicker panel on pass. side an unplugged the module, found a replacement on ebay. seller's name is Bilyl2k. put the new part in truck is fine no scanning to reset just an go

×

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 45 Answers

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;}Hi: If the front diffis fine then it boils down to usually one of three things why it won’tengage. 1 – No power, 2 – relay notworking (located by passenger side) right side or 3 – no vacuum. The 1995 and up Jimmy’s and Blazer’s use thesame system for engaging the front diff. They are all made to “shift on the fly” while driving down the road withnothing to do but press the button on the dash. (Do NOT shift into 4 Low while driving at higher speeds at it can dodamage). If the dash light flashes andyou hear a clicking sound that means you have power to the relay. If the vehicle 4 High lights stops flashingand it goes back into 2 High then the problem is likely that you have no vacuumto the 4 X 4 actuator module which is located below the battery tray. Remove the battery and tray; look for a holeburnt in the vacuum line or actuator module rubber diaphragm. When the activator get vacuum it pulls acable that attaches to the front diff engaging it, when engaged the wires onthe front diff send a signal to the 4 X 4 light on the dash telling you it is engaged). If the battery has ever leaked the acid runsdown onto the actuator causing the problem. If no holes found in the hose or actuator diaphragm I would use batterycables and hook up the battery and start vehicle then check for vacuum byputting my finger on the end of the actuator hose. If there is vacuum then problem in actuatoror cable linkage. If no vacuum I wouldthen trace back the vacuum lines to find where it is off or leaking, NOTE: As the heater control operates on vacuum and some other vehicle systemsdo as well bear this in mind, has your vehicle had heater control problems orbeen running rough, this could explain a lot of potential problems. Attached to the hood on the left side(drivers side) on 1997 and older models is a vacuum (a “ball”) canister, newermodels the canister is located in the left fender by the brake module, makesure the vacuum line is attached there. Please rate this suggestion as I never know if it is worth my timefilling these things out…

Posted on Feb 26, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I need a picture diagram so I can replace the motor on the transfer case.

Posted on Oct 10, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a problem my2000 blazer 4x4 will not disinage back to 2x4 light flash hear clicking noise on passager side behine glove box on outisde under the truck

Posted on Jan 23, 2009

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 s10 blazer transfer case

It's in the right side lower kick panel

Posted on Jul 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change out 4 wheel drive switch on 2004 Yukon


Before trying to replace the switch ,are any lights flashing ? 2hi , 4lo, 4hi etc... Do you know which transfer case yours has ?
Transfer Case - BW 4482-NR4
Transfer Case - NVG 246-NP8
How many buttons ?
The BW 4482 transfer case features a 3-button shift control switch located on the instrument panel.
The NVG 246 EAU transfer case features a 4 button shift control switch located on the instrument panel
Before you replace the switch and finding out that it isn't the problem . The switch is a low voltage input to the tansfer case shift control module (A COMPUTER ) Could have diagnostic trouble codes stored .
DTC B0790
DTC B2725
DTC C0306
DTC C0327
DTC C0329
DTC C0359
DTC C0550
Auto part stores can not read these codes .

The BW 4482 transfer case features a 3-button shift control switch located on the instrument panel. When the vehicle has the ignition key in the RUN position, the transfer case shift control module starts monitoring the transfer case shift control switch to determine if the driver desires a new mode/range position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/range position. The lamp will continue to flash until all shifting criteria have been met and the new mode/range position has been reached, or has been engaged. Once the new mode/range position is fully active, the switch indicator lamp for the new position will remain ON constantly. In addition, the switch includes a VSES request button which sends a voltage signal to the transfer case shift control module. The transfer case shift control module in turn sends a request via the class 2 data bus to the ABS control module which controls the VSES system.

The NVG 246 EAU transfer case features a 4 button shift control switch located on the instrument panel. When the ignition key is in the RUN position, the transfer case shift control module monitors the transfer case shift control switch to determine if the driver desires a new mode/range position. At a single press of the transfer case shift control switch, the lamp of the new desired position will begin flashing to inform the driver that the transfer case shift control module has received the request for a new mode/range position. The lamp will continue to flash until all shifting criteria has been met and the new mode/range position has been reached, or has been engaged. Once the new mode/range position is fully active, the switch indicator lamp for the new position will remain ON constantly.
DTC B2725
Circuit Description
The range/mode switch circuit consists of 5 modes. The transfer case shift control module supplies 5 volts to the switch through the 5 volt reference circuit. The current travel through the resistor of the currently active mode. The current is then returned to the transfer case shift control module through the switch signal circuit.
The transfer case shift control module constantly monitors this signal voltage to determine the condition of the mode switch circuit.
When each of the modes are selected they complete a circuit through their own specific resistor. The transfer case shift control module continuously monitors the switch input to determine whether the Neutral, AWD, 2HI, 4HI, or 4LO mode was selected by the driver.

You may want to take this to a repair shop .

Jul 28, 2017 | Cars & Trucks

1 Answer

I just bought a 2003 superduty crew with a 6.0 diesel it will not go into 4 wheel drive. i have replaced the vacuume pump and the solinoid (they were bad) I have no power to the switch in the dash. i have...


What large square fuse ? The 4X4 switch get's it's B+ voltage from the four - wheel drive control module . computer controlled ! Has two relay's - transfercase hi to low & low to high ,located in the Auxiliary relay box #3 . location left side of radiator core support . Your best bet ,take it to a qualified repair shop that has a diagnostic tool that can communicate with the 4X4 control module . Read code's ! Probably has a code like one of these
P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD control module Go To Pinpoint Test D . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD control module Go To Pinpoint Test A .
But code have a few others as well .
B2105 Throttle Position Input Out of Range Low 4WD control module Go To Pinpoint Test B . B2106 Throttle Position Input Out of Range High 4WD control module Go To Pinpoint Test B . C1728 Transfer Case Unable to Transition Between 2H and 4H. 4WD control module Go To Pinpoint Test C . C1729 Transfer Case Unable to Transition Between 4WD HIGH and 4WD LOW 4WD control module Go To Pinpoint Test D . C1979 IWE Solenoid Circuit Failure 4WD control module Go To Pinpoint Test F . C1980 IWE Solenoid Short to Battery 4WD control module Go To Pinpoint Test F . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD control module Go To Pinpoint Test D . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD control module Go To Pinpoint Test A . P1824 Transmission 4-Wheel Drive Clutch Relay Circuit Failure 4WD control module Go To Pinpoint Test A . P1826 Transmission 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD control module Go To Pinpoint Test A . P1827 Transmission 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD control module Go To Pinpoint Test A . P1849 Transmission Transfer Case Contact Plate A Short Circuit to Ground 4WD control module Go To Pinpoint Test D . P1853 Transmission Transfer Case Contact Plate B Short Circuit to Ground 4WD control module Go To Pinpoint Test D . P1857 Transmission Transfer Case Contact Plate C Short Circuit to Ground 4WD control module Go To Pinpoint Test D . P1861 Transmission Transfer Case Contact Plate D Short Circuit to Ground 4WD control module Go To Pinpoint Test D . P1867 Transmission Transfer Case Contact Plate General Circuit Failure 4WD control module Go To Pinpoint Test D . P1891 Transmission Transfer Case Contact Plate Ground Return Open Circuit 4WD control module Go To Pinpoint Test D .

Nov 27, 2017 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

98 ram1500 4wd while driving makes howling sound stops when i touch the 4wd shifter


Sounds like the shift linkage needs adjusted. Try making it shorter.

Dec 24, 2012 | Dodge Ram 1500 Cars & Trucks

1 Answer

How to remove transfer case from 2002 tahoe


  • Disconnect the ground cable from the negative battery terminal, by using a wrench to loosen the retaining bolt and pulling the clamp off the terminal.

  • 2

    Raise the vehicle and support with jack stands placed underneath the frame.

  • 3

    Drain the transfer case. Locate the drain plug near the bottom of the transfer case. Place a waste oil collection pan underneath the plug and use a socket to remove it. Once all the fluid has drained out, reinstall the plug.

  • 4

    Remove the bolts that connect the rear driveshaft to the rear axle yoke using a socket. Lower the driveshaft, and slide it backward underneath the rear axle to disengage it from the transfer case. Remove it from the vehicle.

  • 5

    Remove the bolts that connect the front driveshaft to the front axle yoke using a socket. Lower the driveshaft, and slide it forward underneath the front axle to disengage it from the transfer case. Remove the driveshaft from the vehicle.

Removing the Transfer Case
  • 1

    Label and disconnect the electrical wires and vacuum lines connected to the transfer case. Use masking tape and a marker.

  • 2

    Remove the transfer case shifter rod. Using needle-nose pliers, remove the clip that connects the shifter rod to the transfer case. Slide the rod away from the transfer case.

  • 3

    Position a floor jack underneath the transfer case. Raise it enough to take the weight of the transfer case off the transmission.

  • 4

    Remove the bolts that connect the transfer case to the transmission using a socket or wrench.

  • 5

    Slide the transfer case rearward to disengage it from the transfer case. Lower the floor jack, and remove the transfer case from the vehicle.


Jan 20, 2012 | Cars & Trucks

1 Answer

Where is the transfer case shift motor located on 2004 dodge dakota


The transmission control module and the transfer case control module are separate parts. The transmission control module is mounted under the hood and controls only transmission functions. The transfer case control module controls only the transfer case, and is located inside the truck. If you remove the trim panel under the steering column you will find the transfer case control module mounted just to the right of the opening.


The shift motor is located just behind the axle tube to prevent damage.
There is a shift motor on the right front axle that is vacuum operated.
The shift motor (1) is an electromechanical device consisting of a DC permanent magnet motor, a motor brake, a gear train and an analog position sensor. The shift motors' overall function is to move and lock a gear that moves the mode fork found in the transfer case. This allows the transfer case to be shifted electrically to multiple operating positions (4LOCK and AWD). The operating current of the shift motor under
stall conditions is 30 amps maximum at 72° F with 13.5 volts, at the motor leads.
OPERATION
Shifting in the transfer case occurs when the shift motor brake is released and a Pulse Width Modulated (PWM) voltage is supplied to the shift motor by the Front Control Module (FCM). A linear analog position sensor located inside the shift motor, provides the FCM with the motors' angular, rotational position. With this information, the FCM
continuously knows the motors' position, and therefore allows it to accurately control the motors' operation, including voltage polarity which is used to control motor direction.

REMOVAL :---Note: New shift motor assemblies are shipped in the AWD position. If a new shift motor assembly must be installed, it will be necessary to shift the transfer case to the AWD position prior to motor installation.
Raise the vehicle on a suitable hoist.Remove the front propeller shaft. Disengage the wiring connectors from the shift motor and mode sensor.Remove the front output shaft companion flange from the transfer case.Remove the bolts (Remove the Shift Motor and Mode Sensor Assembly Bolts) holding the shift motor and mode sensor assembly onto the transfer case.Separate the shift motor and mode sensor assembly from the transfer case. See fig below:-- helpmech_19.gif
1 - TRANSFER CASE.2 - SHIFT MOTOR AND MODE SENSOR ASSEMBLY.3 - BOLT.-- This should help.Thanks.Helpmech.

Feb 26, 2011 | 2004 Dodge Dakota

1 Answer

Canyon 4wheeldrive light turned on


Checking the 4X4 control module for DTC'S - diagnostic trouble codes is what you should done . Need a factory or professional type scan tool , no an OBD2 code reader . Looking at factory service repair info. description of how it works , an testing is how to diagnose . Not guessing an throwing parts at it .
DTC B2725
The accessory switch circuit consists of 4 modes. The transfer case shift control module supplies 5 volts to the switch through the switch signal circuit. The current travels through the resistor of the currently active mode. The current on the switch signal circuit is monitored by the transfer case shift control module. The voltage on the switch signal circuit will vary depending on which mode button is pressed by the driver.
The transfer case shift control module constantly monitors the switch signal circuit to determine the condition of the accessory switch circuit.
When each of the modes are selected they complete a circuit through their own specific resistor. The transfer case shift control module continuously monitors the switch signal circuit to determine whether the Neutral, 2HI, 4HI, or 4LO mode was selected by the driver.

DTC C0327 Encoder Circuit Malfunction
The transfer case shift control module has 4 encoder circuits, and each circuit is supplied 12 volts. These 4 circuits are A, B, C, and P, and each circuit runs to a switch located inside the encoder/motor assembly. When a particular encoder circuit is active, the switch is closed, and the 12 volts are grounded by the switch inside the encoder.
The transfer case shift control module supplies 12 volts on all the circuits. The module can interpret the location of the transfer case shift position when the circuits are grounded.
This DTC detects a fault when it compares the shift sequence/strategy to a chart located in read only memory (ROM), within the electronic control unit (ECU), within the transfer case shift control module. This is accomplished by the module reading the different combinations of encoder signals being grounded while others remain high depending on what mode or range the transfer case is in.

DTC C0550 ECU Malfunction
At each power-up, the transfer case shift control module runs a self-test on the following functions:
• EEPROM Checksum
• ROM Checksum
• RAM Checksum
• RAM Malfunction

I suggest your take your vehicle to a qualified repair shop .

Dec 31, 2017 | 2005 GMC Canyon

1 Answer

Won,t shift transfer case into 4wheel drive


Is the truck on the fly 4X4 push button or is there a lever on the floor you pull into 4 wheel drive? Located on the back of the transfer case not hard to change few bolts and a wire harness. Does the front drive shaft turn when you put it in 4x4 and the front wheels won't ingage? If so then its not your transfer case its the actulator on the front axle at the gear hub or pumpkin it will have two 10mm bolts and a black plastic cover if so remove cover and spray actulator shaft with wd-40.

May 19, 2009 | 2008 Ford F-350

2 Answers

I have a 97 chevy tahoe and the 4x4 wont lock in i just replaced the actuator and it just blinks on 4x4 . i do have 12 volts @ the harness to????


Your transfer case could be locked up. Try pulling the shifter motor (servo) off of the transfer case and manually shifting the vehicle into 4x4. Make sure to block the wheels as it will roll if you shift into neutral. If you cant shift it, you need to have a professional look at the insides of your transfer case.

Dec 22, 2008 | 1997 GMC Jimmy

Not finding what you are looking for?
2000 Chevrolet Blazer Logo

2,188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...