Question about Ford Focus

1 Answer

How do i replace cv joints - Focus Ford Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

How do i replace cv joint boot 98 buick

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace rubber cv boot on 1999 Isuzu rodeo


how to , who can, what are all steps. are there special tools?
sure. if the boot is bad, so be the joint, Yah think?
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Halfshaft from the vehicle
    • Snapring and bearing
    • Snapring and oil seal
    • Mounting bracket
    • CV-joint boot
    • Circlip and inner joint housing
    • Snapring and spacer
    • Inner joint balls
    • Snapring and inner CV-joint
    • To install:
    • Install or connect the following:
      • Inner CV-joint and snapring
      • Inner joint balls
      • Spacer and snapring
      • Inner joint housing and circlip. Add 150 grams CV-joint grease.
      • CV-joint boot
      • Mounting bracket
      • Oil seal and snapring
      • Bearing and snapring
    • Install the halfshaft and mounting bracket to the vehicle.
    • Check the wheel alignment and adjust as necessary.

Jun 30, 2014 | 1999 Isuzu Rodeo

1 Answer

How to replace a cv joint


I can tell you how to replace the CV joint but it is by far better to just buy a re-manufactured axle. The price of the CV joint itself then the labor to remove the axle, change the joint and install it is a big pain. Changing just the CV joint is labor intensive and you could run in to problems. Don't risk it, but a rebuilt.

Mar 23, 2014 | 1994 Toyota Camry

1 Answer

Replace axle but not cv joints


"What we have here is a failure to communicate". The axle comes with CV joints on the end. You will be buying the rebuilt assembly. Both axle and CV joints will refer to the same part in a front wheel drive application.

Feb 19, 2014 | Toyota Sienna Cars & Trucks

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

1 Answer

When makeing a left turn clicking.


this is the sign of a failing outer CV joint in the drive shaft. look under car at driveshaft. the rubber boot around CV joint is probably torn. This allows lube to fling out and water to come in, contaminating the CV joint. Replace the entire drive shaft instead of replacing only the outer CV joint.

Nov 11, 2010 | 1994 Plymouth Voyager

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

02yukon i cannot get the cv joint out from the wheel/brake assem


Remove steering joint.Then bottom ball joint then you should be ok.

Jul 13, 2009 | 2001 GMC Yukon

1 Answer

Can I just replace just one cv joint


Yes you can,I'm not sure if your refering to the whole axle or one cv joint on the axle.Replacing a cv joint is best left to a qualified mechanic,most cv joints require special tools and procedures to replace correctly.

Apr 22, 2009 | 2000 Suzuki Esteem

1 Answer

Dodge Caravan, 2001, CV joints have 1/4" longitudinal play/noise


CV Joint Axle Replacement - How to Repair or Replace

Over time the rubber boots of the CV joints can become cracked, torn, or otherwise compromised. Once moisture and dirt get into a CV joint and grease makes its way out, the CV joints days are numbered. Signs of impending failures are a click-click-clicking or metallic crackling noise while turning and accelerating or a clunking upon deceleration. While one can repack, reboot, and rebuild CV axles, it makes more sense for the average do-it-yourselfer to procure replacement units and swap out the old axles. If a boot is torn or missing, it is possible to save the joint if caught early enough, but usually the damage has already been done. Replacing or servicing the entire CV joint axle assembly may be the smarter move since replacing a boot may involve removing an axle, which may also involve removing half or all of the vehicle's brakes and suspension.

Jan 19, 2009 | 2001 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

766 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...