Question about 2000 Hyundai Sonata

1 Answer

Turn signals do not work, hazard lights work some times. turn signal switch has been replaced

Posted by on

  • kberrett Aug 20, 2008

    turn signals have stopped working

  • Homeyjo Feb 01, 2009

    WHat if you have replaced the flasher can and they are still intermittent? I have read somewhere the hazard flasher switch is in the circuit and can cause this, but how?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 30 Answers

The problem is not with switch.. you need to replace the flasher can or relay.

Posted on Sep 06, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The hazard back lights wont quit blinking when car is running even when i pull the fuse on a 2002 buick regal


What fuse are you pulling ?

Hazard Lamps
The hazard warning switch is part of the turn signal switch. The turn signal switch receives battery voltage at all times through the HAZARD SWITCH Fuse. When the hazard switch is placed in the HAZARD position, battery voltage is applied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher sends a turn signal flasher signal to the turn signal switch. The turn signal switch provides all of the turn lamps and turn indicators with the turn signal flasher signal, simultaneously flashing them on and off.

Turn Signal Lamps
The front turn signal lamps are made up of the front park/turn signal lamps and rear turn signal lamps. The front turn signal lamps flash with the rear turn signal lamps when a turn is initiated using the turn signal/multifunction lever. The turn signals will operate only with the ignition switch in the RUN position and will not operate during hazard flasher operation.
When the ignition is turned to the RUN position, battery voltage is supplied to the TURN SIGNAL Fuse. Battery voltage is then applied through the turn signal fuse circuit to the turn signal switch. When the turn signal switch is placed in the LH or RH position, voltage is supplied to the hazard lamp/turn signal lamp flasher. The hazard lamp/turn signal lamp flasher supplies a turn signal flasher signal to the turn signal switch. With the turn signal switch in the LH or RH position the corresponding turn signal indicator, rear turn signal, and front turn signal receive the turn signal switch signal and will flash. The front turn signals receive the turn signal switch signal from the turn signal switch via the BCM. The turn lamps are permanently grounded.

Replace the turn signal switch. Refer to Multifunction, Turn Signal, and Hazard Switch Replacement - On Vehicle in Steering Wheel and Column - Tilt.

Feb 11, 2017 | Buick Cars & Trucks

1 Answer

How do I fix both turn signals and hazard lights on 1995 Buick custom regal?


First off operate the hazard switch many times. The contacts in the switch corrode through lack of use and this will clean them. As the turn signals and hazard lights share the turn signal unit it may be faulty.

Feb 24, 2015 | Buick Cars & Trucks

1 Answer

Hazard light not working


Replace the hazard switch. If it located in the steering column by the turn signal switch. You have to replace the turn signal switch. They are made together.

Feb 17, 2015 | 2006 Kia Rio

4 Answers

Turn signal lights don't work


The first place to start are fuses, check your owners manual for location, typically left side of dash.

The emergency (hazard) flashers and turn signals are on separate fuses and run through the hazard switch. If all the lights work when the hazard switch is on then the problem will likely be a blown turn signal fuse.

Other possibilities are the hazard switch itself is bad, the turn signal switch is bad or a broken wire, all of which require a meter (or test light) wiring diagram and knowledge of the circuit to test it - better to have it done.

Robert Grove
Mobile Mechanic Malibu 310 651 8020 Auto Truck RV Mobile Repair...

Aug 09, 2014 | 2002 Chevrolet Impala

1 Answer

2005 Impala, directional signals inoperative. Flashers are working. Replaced the hazard warning switch. Still no directional signals, hazards work. Now, car will not start.Buzzing sound from hazard sw


There is a good possibility that the hazard warning and directional signal lights have nothing to do with the starting or operation of the engine. There are many things that might cause the car to fail to start. The battery must be fully charged, and in good working condition. No corrosion on the terminals. good solid connections. When you turn the key the starter motor should turn the engine over. If that works the carburetor will need gas. If you have gas and spark, the engine should run. Hope that helps.
Turn signals work with the tail lights and parking lights on the front. You should turn on the Head lights and check to see if the tail lights and parking lights come on. You will also want to check to see if the flasher is plugged in. All the light bulbs must be plugged in and working to operate the flasher for the turn signals. good luck

Oct 10, 2017 | 2005 Chevrolet Impala

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

2 Answers

After using turn signal you can still hear clinking, is hazard relay part of turn signal


The hazard switch is also the device that supplies the turn signal "flash". If you continue to hear the noise of the turn signal flashing when the turn signals off than the problem is the turn signal switch. It is grounding The purple wire from the hazard switch which makes the hazard switch think the turn signal is on. The fix for this is to relace the turn signal/multi-function switch. Typically they will start to go bad in stages. Your symptom is the first stage. Eventually either the turn signals or the brake lights will also sto working. Let me know if you have any questions and I'll do my best to answer them. Thank you for using FixYa.com!

Feb 10, 2012 | 2000 Oldsmobile Alero

1 Answer

1999 Lincoln Continental was in for repairs and now my turn signals and break lights dont work. Im being told it's something to do with the anti theft system because the battery was unhooked. The...


I suspect there is a problem with the turn signal/ hazard switch. turn the turn signal on left or right, if it doesn't flash, grip the hazard button and gently wiggle it around, if the signals start flashing, replace the turn signal switch. The Brake lights are wired through the turn signal switch, if the 3rd brake light works, the brake switch is OK. I don't think it has anything to do with the anti theft system (at this time)

Sep 21, 2011 | 1999 Lincoln Continental

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

2 Answers

Turn signal doesn't come on until I hit my hazard light on & off


it could be duel filament bulb that is blown and shorting inside the bulb to the other circuit, you may need to remove all indicator and hazard bulbs and check. I would also try a new flasher can

Apr 17, 2010 | 2003 Chevrolet Impala

Not finding what you are looking for?
2000 Hyundai Sonata Logo

458 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...