Question about Pontiac Firebird

1 Answer

Need to take the seat belt off to put the seat belt shoulder guide through it. my old shoulder guide broke off and i orderd a new one but i need to get the seat belt to go through the new one.

Posted by on

  • Anonymous Mar 21, 2014

    the guide is broken and I need to install a new one

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

It's especially hard if you have gained weight.

Posted on Jul 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a seat belt?


Locate the area where the seat belt originates.

Remove the safety bolts located under the casing with a socket wrench. At the other end of the seat belt, remove the nut which holds it in place with a wrench.

Remove the shoulder harness of the seat belt with the wrench.Remove the bolt and nut which is attached to the anchor side of your old seat belt. This is at the bottom of the vehicle.Install the new anchor section of the seat belt.

http://www.xcardiag.com/

Jun 29, 2014 | 1984 Chevrolet Corvette

1 Answer

How to remove a back seat from 02 toyota avensis


Hi, peel the cover from around the seat frame so that the shoulder strap hold the cover on to the seat.

Extend the set belts to their maximum length and recline the seat as far as possible.

Looking at the seat from the front, put your hand in the gap between the reat of the seat (bit that reclines) and the fromt of the fixed base (by the red dome and the instructions).

On the bit of the seat that reclines there is a 'door' that opens to reveal a metal clasp that the ends of the shoulder straps fix to at the top and the ****** belt at the bottom.

Unhook the looks from the shoulder straps from the metal clasp.

Pull the shoulder straps through the back of the seat upright. You can now pull them through the cover which is free for you to wash.


Thank you.

Jun 06, 2012 | Cars & Trucks

1 Answer

I keeping blowing the fuse that powers the shoulder belt and power windows. What is making that happen?


Most likely a short. Or a motor in the seat belts or windows that is being strained. More strain=more amps=blown fuse. try to spray Silicone spray in the track guides for the seat belts, and windows.

Aug 15, 2010 | 1988 Toyota Cressida

2 Answers

1990 CAMRY - Automatic shoulder belt doesn't operate


right thinking, check the fuse then the relay.that's what it is most of the time.

Jul 14, 2009 | 1988 Toyota Camry

1 Answer

How do we fix front passenger side seat belt retractor on 1999 Ford Taurus? It will not pull out....


you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:
  1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
  1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
  1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
sxh~us~en~file=ani_caut.gif~gen~ref.gif WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

Apr 21, 2009 | 1999 Ford Taurus

1 Answer

Install seat belt through seat belt guide 1990 camaro


The new seat belt guides will have a **** in them that allows you to put the belt through it. If it's a used guide taken off another car it may not have the ****.

Mar 16, 2009 | 1990 Chevrolet Camaro

1 Answer

Driver shoulder seat belt strap hookup is stuck and won't move.


Hondas and other cars have their seat belts guaranteed for life. Call your local Nissan repair shop and see if this is so. If so, they shouldn't charge you a dime. I bought a very old used Honda once, the seat belt broke, and I got a brand new one installed for nothing.

MomsyKat

Aug 08, 2008 | 1997 Nissan Quest

2 Answers

Electric retractable seat belt problem


check your fuses. there is also a lever next to te parking brake..make sure it's down

May 17, 2008 | 1988 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...