Question about 1999 Chevrolet Malibu

1 Answer

I need to take the door panel off of my 1999 Chevy Malibu

Posted by on

  • pegleg0723 May 03, 2009

    My window won't roll up on my chevy malibu so I need to take the door off the see what the problem is

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had this problem you can just pop it off and it will snap back on. It was the window motor and I went to a junk yard and only paid $35.00 for the part compared to $500.00 the dealer wanted.

Posted on Jul 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for the brain on a 99 chevy malibu


there are three fuse's for the ( pcm ) powertrain control module ! engine brain ! two are in the under hood fuse/relay junction block.
it is marked pcm / batt. fuse.10 amp. the other is pcm / ign fuse 10 amp. and then there is one in the let hand instrument panel fuse box. open the driver door at the end of the dash pull off end panel, fuse box behind there. fuse is marked pcm / acc 10amp .

now what is the problem your having ? i can help !

Jan 21, 2015 | 1999 Chevrolet Malibu

1 Answer

Remove golve compartment on 1999 chevy malibu


There's only so many screws that hold the glove box in. Some are inside the glove box and some are underneath. You may need a torx wrench depending on the type of screws holding the glove box in.

Feb 18, 2013 | 2000 Chevrolet Malibu

1 Answer

How can I remove the back door panel for my 1999 chevrolet malibu?


the rear door panel? it has a few screws on the door handle, and then is a large screwdriver, and a gentle hand. if you run into any tough points then there maybe another screw, but there should only be 2-3 at most.

Jun 24, 2011 | 1999 Chevrolet Malibu

1 Answer

How to replace a window motor and regulator in a 1999 chevy malibu


TRY IT YOUR SELF VERY EASY,,few nuts then only one plug,,job done,,take off panel inside door,,very easy from then on,,few bolts ,,thats it

Jun 18, 2010 | 1999 Chevrolet Malibu

1 Answer

2007 malibu max rear door panel removal


how do i get the rear driver door panel off without distroying it???
2007 chevy malibu maxx 6cyl.
Stb723@gmail

Mar 23, 2010 | 2007 Chevrolet Malibu Maxx LTZ Hatchback

2 Answers

99 Chevy Malibu - auto trans - no dipstick


You have what is called a closed cased transmission. You have to crawl underneathe to get to the tranny and remove the upper bolt close to the side of the case (more towards the bottom of the transmission). When you fill it, you fill it till it starts to drip out of that hole.

Looking for a picture for you.

Jun 06, 2009 | 1999 Chevrolet Malibu

2 Answers

Drivers door panel removal


The book says 1. remove power accesory switch panel by using suitable flat blade tool at front. 2. Disconnet electrical connections.
3. pry door handle plug by using small flat bladed tool
4.remove door trim handle mounting screws
5. remove door trim panel from retainers.Start at rear bottom corner and pry outward.
6. remove door panel.
KD does make a tool that will properly pry the door panel away from reainers. KD 3705 You might get by with a screwdriver.
One other thing you may need to have the window down to get the panel to come off. You will have to lift up on it once it is loose from the fastners.
Hope this helps you out.

Mar 23, 2009 | 2003 Chevrolet Malibu

1 Answer

How remove rear door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Feb 20, 2009 | 1999 Chevrolet Malibu

1 Answer

Torque specks


hi 1999 chevy malibu head bolts 1-8 40 ft lbs bolts9-10 30 ft lbs tighten all bolts an additional 90 degrees

rod bearings 18 ft lbs plus additional 80 degrees

head
top row of bolts 9 3 1 5 7 bottom row 10 6 2 4 8 from left to right

Feb 12, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...