Question about Ford Mustang

1 Answer

07 ford mustang gt MAKING a whining like tire but louder noise from the rear when crusing just had the rear differential gear replaced and housing

Posted by on

  • Anonymous Apr 20, 2009

    I have the problem, The dealership just replaced the bearings in the rearend, and now it seems to be worst. Im still looking for a solution.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

Do you know if the correct fluid (plus the required friction modifier) and fluid level were used? I'd take it back to where you had the work done and have them take a look at it and confirm the above if you don't know. If the above is correct, I'd think there is still something wrong inside.

Posted on Jul 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 Mustang is making a clunking noise from the rear driver side wheel, recently the wheel bearings were changed at a Ford dealership could they have screwed this up


Oh yeah, the definitely could have forgotten to put gear oil back in the rear. Pull the plug on the rear that's on the back of the differential center about half way up and stick your little finger in and curl it down to see if there's any in it.

Dec 01, 2014 | 2009 Ford Mustang GT

2 Answers

Why is the rear end making a whining noise


The whining noise could be for many reasons. Narrowing the possibilities depends on when the noise occurs. If it happens only while decelerating at any or all speeds is most likely caused by bad pinion bearings or loose pinion bearing preload. If it happens during acceleration over a small or large speed range is usually caused by worn ring and pinion gears.

One cheap thing to check is the fluid level in the differential. If low, topping off the lube may help for a while.

Jun 12, 2014 | 2000 Ford Mustang

1 Answer

Whining in rear end 2007 toyota 4 runner


check your sliders holding the pads .take off ,and clean and grease them

Dec 26, 2013 | Toyota 4Runner Cars & Trucks

1 Answer

Have a loud whine from rear differential. gets louder with acceleration stops when not . replaced pinion bearing but still making noise. also the pinion has chewed into the gear housing somehow. how to fix


SOUNDS LIKE WORN BEARINGS OR IMPROPERLY SET UP UNIT. RECOMMEND TEARDOWN AND INSPECT ALL BEARINGS AND RACES . IF OK INSTALL NEW RING AND PINION ,,,,USE THE CORRECT SET UP TOOLS AND PROCEDURE!!!!!

Aug 06, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

How to remove gears from differential on a 95 mustang v6


Removal
  1. Raise vehicle and place jackstands under rear frame crossmember. Lower the hoist so that rear axle housing is at suitable working height.
  1. Remove axle housing cover from rear axle housing and drain lubricant.
  1. Perform the inspection before disassembly.
  1. Remove rear wheels, rear disc brake calipers and rear disc brake rotors.
  2. Working through cover opening, remove differential pinion shaft lock pin and remove differential pinion shaft and differential pinion gears (4215). 3fdbe2c.gif
NOTE: THIS IS FREE INFORMATION!!!!
  1. Remove rear brake anti-lock sensor . Push axle shaft inward until u-washers at button end of the axle shaft are clear of side gear recess.
  1. stb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage inner wheel bearing oil seals when removing axle shafts from rear axle housing. In addition, axle shafts should be completely removed from rear axle housing.
    Remove u-washers and pull axle shafts out of the rear axle housing. 85189ce.gif

Mar 25, 2010 | 1996 Ford Mustang

2 Answers

Refill gear oil in rear differential on 2003 ford mustang gt


The differential will have a plug in the driver's side of the housing that is removed with a 3/8" drive ratchet or square drive. Be sure you know what type of fluid is recommended for your vehicle. It will depend on whether it is a locking differential or standard.

Sep 21, 2009 | 2003 Ford Mustang

1 Answer

Rear drivetrain noise whine getting louder and louder


if it is the gears in the diff,it is pricey.
since most trucks get overloaded and this is the result,that is why the rule is 25% and lifespan is reduced by 50%
overload 50% and it is 200%

May 28, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Rear Axel Seal


Wheel, brakes etc that are in way of pulling axle out have to come off. Drain rear end fluid, remove rear housing cover, remove bolt that holds pin in differential, remove differential pin, push in slightly on axle to remove "U" clip that holds shaft in, then slide shaft out. replace seal. Reverse procedure for re-install & fill with gear lube. If any questions, get back to us.

Apr 16, 2009 | 2002 Ford Mustang

2 Answers

Rear wheel bearing


SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Apr 10, 2009 | 2004 Ford GT

2 Answers

Noise in 2004 Ford Mustang V-6, Manual Transmission


Check the rear suspension bushs for looseness wheel could be pulling to and fro when under power. The noise is probably due to the rubber bush completly disintegrated and the axle to body insulation has gone making the body a big megaphone

Mar 11, 2009 | 2004 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...