Question about 2005 Dodge Neon

2 Answers

Location of the mounting bolts for a starter - 2005 Dodge Neon

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

BOLTS ARE LOCATED ON BOTH SIDES OF STARTER--ONE ON TOP GOES IN FROM BELL HOUSING SIDE...ONE ON BOTTOM GOES FROM STARTER SIDE---I SEE SOMEONE NEEDS TO LOOK AT A MANUAL FOR THIS BASIC QUESTION--HAYNES REPAIR MANUAL AT AUTOZONE FOR $15.00 BUCKS IS WORTH THE COST FOR THE 05 NEON.

Posted on Aug 02, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 60 Answers

They are around the edge of the starter since they have to hold the starter. If it is a higher mileage car, you may have to do a bit of cleaning to find them. Also, the bolts go in towards the transmission.

Posted on Jul 23, 2008

2 Suggested Answers

SOURCE: where are the motor mount bolts

Your under the car working on the starter

You look at the mounts,they have to have at least 2 or 3
bolts holding them to the sub frame,you don't remove the
engine side of mount !!!

Posted on Dec 09, 2012

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove Starter. How many bolts hold the starter to the block


What is year--make--model?
Generally two bolts, but, I can't see anything from here. Look at the new starter motor and you should see how many mounting bolts. You can look up new starter motor in online partsbook, should show a picture with mounting bolt locations.

Apr 07, 2016 | Cars & Trucks

1 Answer

Replacing a starter in a sebring 2006


All of the nuts and bolts are metric on it. It helps to use a 13mm swivel socket on the starter bolts but you can use a wrench if you need to. Also, a 7/8 open end wrench for the 02 sensor, or an 02 sensor socket.


Let me give you the steps for the starter and also the front engine mount bracket. You don't have to remove the entire mount, just the bracket




REMOVAL

  1. Open Hood.
  2. Disconnect the negative battery cable.
  3. Raise vehicle and support.
  4. Disconnect the electrical connector from the 02 sensor.



2009-10-31_143231_starter1.gif




  • Remove the 02 sensor from the exhaust manifold .
  • Remove the front mount through bolt.
  • Remove the front mount bracket from engine block.







  • 2009-10-31_143306_starter2.gif



    Remove the battery cable from starter.




    2009-10-31_143343_starter3.gif



    1. Remove the lower starter bolt and remove starter.

    INSTALLATION

    1. Install starter to transmission.
    2. Start the upper starter bolt.
    3. Start the lower bolt and snug it so that the starter will not move.
    4. Remove the upper bolt.
    5. Connect the battery cable and torque nut to 8.5 Nm (75 in. lbs.).
    6. Install the front mount bracket and check heat shield location.
    7. Install bolt the upper bolt and torque bolt to 54 Nm (40 ft. lbs.)
    8. Install the lower and torque bolt to 54 Nm (40 ft. lbs.)
    9. Install the front mount through bolt and torque bolt to 61 Nm (45 ft.. lbs.)
    10. Install the 02 sensor and torque to 27 Nm (20 ft. lbs.)
    11. Lower vehicle.
    12. Connect the negative battery cable.




    FRONT MOUNT

    REMOVAL

    1. Raise vehicle.




    2009-10-31_143650_mount1.gif



    1. Remove front mount to bracket horizontal through bolt (Fig. 87).
    2. Loosen the rear mount through bolt.
    3. Remove front mount vertical bolts (Fig. 87).
    4. Remove front mount and separate the starter heat shield.

    INSTALLATION

    1. Position front mount on lower radiator crossmember.
    2. Loose install front mount to bracket through bolt.
    3. Install front mount vertical bolts. Tighten bolts to 61 Nm (45 ft. lbs.) . (Fig. 87).NOTE: Be sure the weight of the engine is static and in rest position. this for a 2.7 v6

    Jan 15, 2012 | 2006 Chrysler Sebring

    1 Answer

    Location of "starter" for 1999 cadillac catera


    Hi, if you have the 3.0 liter engine, see instructions below. If you have the 4.6 liter, the starter is under the intake manifold.

    Removal & Installation

    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Remove or disconnect the following:

      Negative battery cable Starter electrical connectors Right hand catalytic converter Right side engine mount nuts Intake air resonator to the throttle body ducts
    3. Install an Engine Support Fixture to the right side of the engine.
    4. Raise the right side of the engine approximately 1.5 inches (38mm) to gain access to the starter motor bolts.
    5. Remove or disconnect the following:

      Engine mount from the bracket and cradle Engine mount bracket bolts and reposition the bracket Starter motor


    6. jturcotte_2359.gif

      Fig. Remove the starter motor and bolts


    To install:
    1. Install or connect the following:

      Starter motor. Torque the bolts to 44 ft. lbs. (60 Nm). Engine mount to the bracket and front crossmember. Torque the bolts to 30 ft. lbs. (40 Nm).
    2. Lower the engine into position and make certain that the mount locator tab is fully seated in the front crossmember slot.
    3. Remove the special tools from the engine.
    4. Install or connect the following:

      Engine mount nuts. Torque the upper nut to 30 ft. lbs. (40 Nm) and the lower nut to 41 ft. lbs. (55 Nm). Intake air resonator to the throttle body ducts Catalytic converter. Torque the bolt to 25 ft. lbs. (34 Nm) and the nuts to 18 ft. lbs. (25 Nm). Starter electrical connectors. Torque the battery cable nut to 115 inch lbs. (13 Nm) and the starter solenoid nut to 35 inch lbs. (4 Nm). Negative battery cable

    Oct 03, 2011 | Cars & Trucks

    1 Answer

    Where is the starter located on my 2003 nissan sentra ser


    Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
    3. Lightly lower the transmission to make room and pull out the dipstick tube.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Connector bracket from the front mount bracket
      • Harness connector
      • Starter bolts
      • Starter
      To install:
    5. Install or connect the following:
      • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
      • Harness connector
      • Connector bracket to the front mount bracket
      • Dipstick tube
      • Transmission into position
      • 4 rear mounting bracket bolts
      • Negative battery cable
    6. Remove the transmission jack
    WITH MANUAL TRANSMISSION
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Connector bracket from the front mount bracket
      • Harness connector
      • Starter bolts
      • Starter
      To install:
    3. Install or connect the following:
      • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
      • Harness connector
      • Connector bracket to the front mount bracket
      • Negative battery cable
    1.6L and 2.0L Engines
    1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
    2. Remove or disconnect the following:
      • Negative battery cable
      • Wiring at the starter
      • Bolts attaching the starter to the engine
      • Starter
      To install:
    3. Install or connect the following:
      • Starter and torque the bolts to 70 inch lbs. (8 Nm)
      • Starter electrical connections
      • Negaative battery cable
    Maxima
    1. Remove or disconnect the following:
      • Negative battery cable
      • Air duct
      • Harness protector from the harness
      • Starter wiring at the starter
      • Starter-to-engine bolts
      • Starter from the vehicle

        Image 89612G12l Not Found

      To install:
    2. Install or connect the following:
      • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
      • Starter wiring
      • Harness protector
      • Air duct
      • Negative battery cable
    Altima
    1. Remove or disconnect the following:
      • Negative battery cable
      • Air inlet tube
      • Harness bracket
      • Wiring at the starter
      • Starter
      To install:
    2. Install or connect the following:
      • Starter and torque the bolts to 60 inch lbs. (7 Nm)
      • Starter electrical connectors
      • Harness bracket
      • Air inlet tube
      • Negative battery cable

    Nov 03, 2010 | 2003 Nissan Sentra

    2 Answers

    My pacifica is doing a rapid clicking when i try to start it and will not start. I would assume it is the starter??? Where is the starter located on an 2005 pacifica 3.5L?


    CHECK BATTERY VOLTAGE FIRST SHOULD BE 12.5 VOLTS.IF NOT BATTERY WEAK.MAKE SURE BATTERY CABLES TIGHT CLEAN FREE FROM CORROSSION.FIRST TURN OFF RADIO BEFORE REMOVING NEGATIVE BATTERY CABLE TO KEEP FROM LOCKING OUT RADIO.IF BATTERY OKAY SOUND LIKE FAULTY STARTER SOLENOID.STARTER LOCATED NEAR FRONT MOUNT YOU HAVE TO REMOVE UPPER NUT FROM FRONT MOUNT,REMOVE LOWER FRONT MOUNT NUT,REMOVE LOWER BRACKET TO TRANSMISSION BOLT,REMOVE LOWER BRACKET TO ENGINE BLOCK BOLT,MOVE THE FRONT MOUNT AND BRACKET OUT OF THE WAY.THEN REMOVE ALL STARTER BOLTS AND THE STARTER POSITIVE BATTERY CABLE FROM STARTER SOLENOID.

    Oct 02, 2010 | 2005 Chrysler Pacifica

    1 Answer

    1988 Chevy Tahoe Starter going out. Need to replace


    Generally starters have 2 or 3 bolts and a thick wire coming from the battery and other miscellaneous connections.

    You did not specify a vehicle that was on my list, i.e. 1988 Chevy Tahoe.

    However, it may be similar to a Suburban R10:
    REMOVAL & INSTALLATION The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
    1. Disconnect the negative battery cable at the battery.
    2. Raise and support the vehicle.
    3. Disconnect and tag all wires at the solenoid terminal. NOTE: Reinstall all nuts as soon as they are removed, since the thread sizes are different.
    4. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter. Fig. 1: Starter mounting location — 4.8L engines 84903021.gif
      Fig. 2: Starter mounting location — 4.3L and 5.0L engines 84903022.gif
      Fig. 3: Starter mounts — 5.7L and 7.4L engines 84903023.gif

    5. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck. To install:
    6. Position the starter and tighten all bolts as follows: R/V Series:
      • Thru-bolts: 40 ft. lbs. (54 Nm)
      • Bracket bolt: 30 ft. lbs. (41 Nm)
      • Nut (gas): 11 ft. lbs. (15 Nm)
      • Nut (diesel): 90 inch lbs. (10 Nm)
      C/K Series:
      • Thru-bolts: 35 ft. lbs. (45 Nm)
      • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
      • Nut (diesel): 75 inch lbs. (8.5 Nm)
    7. Reconnect all wires. Fig. 4: Disconnect the negative battery cable 87982p25.jpg
      Fig. 5: Remove the starter retaining bolts 87982p30.jpg
      Fig. 6: Remove the starter from the vehicle 87982p31.jpg
    prev.gif next.gif

    Jul 19, 2010 | 1984 Chevrolet Chevy

    2 Answers

    Where is the starter on a 1999 s-10


    passenger side, under exhasut pipe, against motor, close to tranni.

    Jul 17, 2010 | 1999 Chevrolet S-10 Pickup

    2 Answers

    How do you replace the starter on a 1989 SW1500?


    The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
    1. Disconnect the negative battery cable at the battery.
    2. Raise and support the vehicle.
    3. Disconnect and tag all wires at the solenoid terminal.
    Reinstall all nuts as soon as they are removed, since the thread sizes are different.
    1. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.

    f6823f2.gif
    Starter mounts-5.7L and 7.4L engines

    1. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck.
    To install:
    1. Position the starter and tighten all bolts as follows:
    R/V Series:
    • Thru-bolts: 40 ft. lbs. (54 Nm)
    • Bracket bolt: 30 ft. lbs. (41 Nm)
    • Nut (gas): 11 ft. lbs. (15 Nm)
    • Nut (diesel): 90 inch lbs. (10 Nm)
    C/K Series:
    • Thru-bolts: 35 ft. lbs. (45 Nm)
    • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
    • Nut (diesel): 75 inch lbs. (8.5 Nm)
    1. Reconnect all wires.450af3b.gif

    Disconnect the negative battery cable


    56132e9.gif
    Remove the starter retaining bolts


    d54e957.gif
    Remove the starter from the vehicle

    Apr 26, 2010 | 1989 Chevrolet Suburban

    1 Answer

    Where is starter located and how to remove it , for a dodge caravan 1998,3.3l


    Starter - Removal & installing
    1. Disconnect the negative battery cable.
    2. Raise and safely support the front of the vehicle securely on jackstands.
    3. Disengage the solenoid wiring connector from the terminal. This connection may be held in place by a retaining nut, or it could be a push-in connector.
    4. Remove the B+ nut and wire from the starter motor terminal.
    5. Remove the starter motor-to-transaxle bellhousing mounting bolts.
    6. Remove the starter from the vehicle. If equipped, remove the starter motor spacer.
    To install:
    1. If equipped, hold the starter motor spacer in position.
    2. Install the starter motor into position on the vehicle.
    3. Install the starter motor-to-transaxle bellhousing mounting bolts. Tighten the mounting bolts to 40 ft. lbs. (54 Nm).
    4. Engage the solenoid wiring connector onto the starter terminal.
    5. Connect the B+ wire and tighten the retaining nut to 90 inch lbs. (10 Nm).
    6. Lower the vehicle.
    7. Connect the negative battery cable.
    8. Verify starter motor operation.
    020fef8.jpg

    Disengage the solenoid wiring connector, then the battery positive (B+) nut and wire from the starter motor

    98933b2.jpg

    Remove the 3 starter motor-to-transaxle bellhousing mounting bolts

    e2afde4.jpg

    Remove the starter motor from the vehicle


    The starter relay is located in the Power Distribution Center (PDC) in the engine compartment. Refer to the underside of the PDC cover for starter relay location.

    Hope helped with this (remember rated this help) Good luck.

    Nov 18, 2009 | 1998 Dodge Grand Caravan

    1 Answer

    Need to replace starter im not mechanical incline. i know basic


    Get a chilton manual online if you a DIYer and it will save you time and money..Basic step by step-Remove postive batt cable. locate starter, obtain new starter to see location of mounting bolts,remove starter mounting bolts,remove wires firrst if accessable if not starter will lower when mount bolts out ,then remove wires noting where they go. hookup wires and replace in reverse. note:some can be hard to get to-always handy to refer to a manual Good luck..oh replace positive cable when aal is tight and right...

    Jan 20, 2009 | 1990 Nissan Pathfinder

    Not finding what you are looking for?
    2005 Dodge Neon Logo

    Related Topics:

    85 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    64052 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...