Question about 1999 Chevrolet Blazer

1 Answer

License plate lamp

How do i get to the lamp to change the bulb?

Posted by on

  • Anonymous Feb 12, 2009

    This did not make my lights work. I think it may be a fuse.

  • exoticpets Feb 24, 2009

    I have changed the license plate lamp bulbs, and believe it's the fuse. Have looked at both diagrams for the fuse boxes (Fuses under the hood and fuses inside), but there is nothing that states specifically "License Plate Fuse". Can someone tell me under what category is this fuse?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Left side lamp, with some soft force you twist it clockwise. Reverse action to reinstall.
Right side lamp, twist it counterclockwise. Reverse action to reinstall

Posted on Dec 31, 2008

6 Suggested Answers

eitan
  • 291 Answers

SOURCE: changing license plate lamps on the tracker

There's no need to take the whole back panel off to do it, the light cover on the bulb twists out, and it might take some elbow grease to twist it, then the bulb is easy to change.

Good luck,
Eitan.

Posted on Jun 10, 2008

  • 160 Answers

SOURCE: Change License Plate Light Bulb

you should be able to get to thru the trunk

Posted on Dec 10, 2008

  • 98 Answers

SOURCE: how do you change the license plate light bulb

OK>>> it is very cold here, but nonetheless..I went outside to check on my Oldsmobile for your benefit....On mine (I can't guarantee it is the same for all of the vehicles listed above). If you are looking at the license plate, LOOK UP and you should see the bulb and whatever encasing is there. Mine is in a tube and it is attached with (2) mini bolts that will need to come out first, then it just looks like a simple matter of disconnecting the electrical plug, taking out the old bulb and putting the new one in. I hope this helps someone....

Posted on Feb 23, 2009

c17hydro
  • 2984 Answers

SOURCE: how to change the license plate light on 2001 ford focus zx3

Take a thin blade screw driver and gently pry between the rubber seal and the metal and pop the light out, replaced the bulb and pop the light back in. works fine.

Posted on Mar 22, 2009

  • 1779 Answers

SOURCE: license's plate light stopped working even with new bulb.

It wouldn't be a fuse if that's the only light that's not working, I believe all of the parking lights are on the same fuse. It's most likely a bad ground or corrosion inside the socket where the bulb makes the electrical connection. So check the socket to make sure it has no corrosion, if it does, clean it up and apply some dielectric grease (available at any parts store) to prevent future corrosion, and check for a loose or broken ground wire.

Posted on Apr 13, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

How to replace License Plate Bulb '96 Jeep Grand Cherokee Limited


Hi Timmy:

Check this procedure from Repair manual...


LICENSE PLATE LAMP - REMOVAL
(1) Remove screws and license plate lamp visor from liftgate (Fig. 10).
(2) Remove bulb from lamp socket.

INSTALLATION
(1) Install a bulb in lamp socket.
(2) Position license plate lamp visor on liftgate and install screws (Fig 10).


4_28_2012_5_22_57_pm.jpg


Hope this helps.

Apr 28, 2012 | 1996 Jeep Grand Cherokee

1 Answer

How do I change my license plate bulb?


{: ) You need to remove first the screws from the license lamp, afterwards you can remove the license lamp from the rear compartment lid. Then ypu have to remove the bulb/socket from the license lamp by rotating counterclockwise. You may remove now the bulb from its socket ( if required).

Aug 31, 2011 | 2003 Oldsmobile Alero

1 Answer

How do i change the license plate bulb on a 2004 tb ls


here is the instructions on how to replace license plate bulbs.

Remove the 2 screws that retain the license lamp lens to the liftgate.

  • Remove the license lamp lens from the liftgate.
  • Remove the bulb (1) from the socket.


  • 8e7cf48.gifaba90ae.gif

    Oct 11, 2010 | 2004 Chevrolet TrailBlazer

    1 Answer

    Change tag light bulb


    1. Remove two screws retaining the lamp to the rear license plate lamp shield.
    1. Rotate socket one quarter turn from backside of lamp and remove the miniature bulb (13466) .

    1. Install new miniature bulb into socket.
    1. Install socket in lamp .
    1. Secure lamp to rear license plate lamp shield with two screws and tighten to 2 Nm (18 lb-in).


      ak1473a.gif


      Item Part Number Description 1 13508 Rear License Plate Lamp Shield 2 14A583 Lamp Lead Wire 3 383356-S Nut (4 Req'd) 4 56000-S Screw (4 Req'd) 5 13550 Lamp (2 Req'd) 6 13466 Miniature Bulb (2 Req'd) A — Tighten to 2 Nm (18 Lb-In)

    Feb 27, 2010 | 1998 Ford Windstar

    1 Answer

    1999 Dodge Neon rear license Plate bulb


    LICENSE PLATE LAMP BULB
    REMOVAL
    1. Remove screws attaching license plate lamp to rear bumper
    2. Remove lamp from bumper.
    3. Remove bulb socket from lamp.
    4. Pull bulb from socket.

    INSTALLATION
    1. Install bulb into socket.
    2. Install bulb socket into lamp.
    3. Place lamp in position.
    4. Install screws attaching license plate lamp to rear bumper.

    Oct 08, 2009 | 1999 Dodge Neon

    1 Answer

    License plate bulbs on 98 Park Avenue


    License Plate Lights Removal & Installation 1997 – 2000 To Remove:

    License/backup Lamp Assembly


    76707d9.gif

    1. Remove the rear compartment lid trim. (if necessary)
    2. Disconnect the license/backup assembly connector from the body harness.
    3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
    4. Remove the license lamp housing from the license/backup lamp assembly.
    5. Remove the license lamp bulb from the housing and socket.
    To Install:
    1. Install the license lamp bulb into the socket and housing.
    2. Install the license lamp housing onto the license/backup lamp assembly
      • Torque the fastener to 18 in-lb (2 Nm).
    3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
    4. Install the license/backup lamp assembly
      • Torque the fasteners to 53 in-lb (6 Nm).
    5. Connect the license/backup assembly connector to the body harness.
    6. Install the rear compartment lid trim. (if necessary)

    Jun 30, 2009 | 1998 Buick LeSabre

    1 Answer

    How do I change the rear license plate light bulbs?


    License Plate Lights Removal & Installation License plate lamp retainer clips
    a555c7b.gif
    To Remove:
    Remove or disconnect the following:
    1. License plate
    2. Pin-type retainers and the luggage compartment lid trim panel
    3. License plate lamp electrical connector
    4. Lamp socket from the license plate lamp
    5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
    To Install:
    1. Install or connect the following:
    2. License plate lamp
    3. Lamp socket to the license plate lamp
    4. Electrical connector
    5. Luggage compartment lid trim panel
    6. License plate

    Jun 06, 2009 | 2000 Lincoln LS

    1 Answer

    License plate bulb 99 alero


    remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

    Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

    1 Answer

    Changing license plate lamps on the tracker


    There's no need to take the whole back panel off to do it, the light cover on the bulb twists out, and it might take some elbow grease to twist it, then the bulb is easy to change.

    Good luck,
    Eitan.

    Jun 08, 2008 | 2000 Chevrolet Tracker

    Not finding what you are looking for?
    1999 Chevrolet Blazer Logo

    368 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    70346 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6869 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...