Question about 2003 Kia Sedona

1 Answer

Spark plugs how do I get to the back spark plugs ? is there a diagram somewhere ?

Posted by on

1 Answer

NO but belive me i did mine not easy but can be done and i did that.Only 5 mm bolts on rear side are little tough and thats it,just feel them and open them.Pl remove some connectors and two race wires.Now remove top 10 mm bolts and lift manifold pl carefully just try to save and put some cover on intake.now change ur plugs and use NGK.

Posted on Jul 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Firing order chev s10 4.3 printable


There will be an EPA sticker somewhere inside of the engine compartment, which will have a diagram of vacuum routing, specification for spark plug gap, and FIRING ORDER.

May 04, 2015 | Chevrolet S 10 Cars & Trucks

1 Answer

Doesnt seem to be any spark,how do i test this


Pull One of the Spark plugs out and connect it back into the plug wire and ground the plug to the body of car somewhere staying away from the fuel lines! While cranking it over see if the spark plug is sparking against the body. This will let you know if your getting spark or not.

Oct 17, 2013 | 1991 Oldsmobile Cutlass Calais

1 Answer

It was runing fine then i changed tha wires and cap now it wont start


See if you get spark from any of the plug wires(use a zip tie or something to ground an old spark plug to the engine block or other metal on engine,connect a wire and crank it)If you do get a spark,you probably mixed up the wires at the cap)If not,then maybe rig up some way to see if you get anything from the coil(I'm assuming it's the "coil in cap" design)IF you did mix up the plug wires,you'll have to find a diagram somewhere to correct it.After correcting it and getting it running,clean a spot off somewhere under the hood,and make a drawing for future reference with a Sharpie marker,then spray a little clear paint over it(I have done this on every engine I have)

Jan 02, 2012 | 1993 Cadillac Seville

1 Answer

Tuned up my 2004 mustang 3.9L I think I got the spark plug wires crossed. is there a diagram somewhere showing where each wire goes?


the coil pack should be marked with a little diagram. . the passenger side cylinders are 1 2 3, drivers side is 4 5 6

Aug 04, 2011 | Ford Mustang Cars & Trucks

1 Answer

How do i know my spark plugs are firering in the


The best way would be to obtain a firing order diagram and go by that. You can probably look at the diagram somewhere online for nothing. Crossed wires are a pain to guess at.

Jul 10, 2010 | 1995 Chevrolet Cavalier

1 Answer

How do I install a distributer on 1998 vortec engine. old distributer missing


Hi: To Install the Distributor Correctly, 1st thing to do is Remove your #1 Spark Plug assuming it will turn over have someone Turn the Key Off and On in Short Intervals.Either put a Compression Gauge in the #1 Spark Plug HoleOr the Old Fashion Way Works as well just put your Finger in the #1 Plug Hole.As your Helper Cranks the Engine On -Off On -Off.Not A Continuous Crank.When You Feel Air Pressure or See gauge Come up.TYhats when your Engine is a The compression Stroke.Now you Can Drop the New Distributor in its Hole.NOTE: You'll need a Spark Plug and Timing Diagram to See the Position your Distributor ROTOR Line it up to where the Diagram Shows your #1 Spark Plug Wire Will go in the Distributor Cap.If the Distributor Rotor is Not n That Position Your goning to Get Either Back Firing engine May Not Even Stsrt, To This Is Crucial. After The Know that you have The Distributor Droppped The Right position you'll need to Put Gap your Plugs at the Correct Specs, With All Plugs in Now You'll need to Put New Plug Wires on .And They MUST be in the correct order.Sitting inside your Vehicle #1 Plug is the Front Plug on the Drivers Side Next is #3 plug Next is #5 and Your Back Plug is Number 7,On the other side Passenger Front Plug is #2 next #4 Next is #6 and the Back is #8 Assuming you know have your Distributor Dropped in The Proper Position, Put the #1 Spark Plug Wire on the Front Spark Plug (Drivers Side) The Spark Plug Firing Order in Your Engine is 1-8-4-3-6-5-7-2 Clockwise So the Next hole after you have #1 Plug and Wire on And Distributor In Correct Position on COMPRESSION STOKE, Going Clockwise you next wire will be your #8 Position in The Cap And it wil go to the Back Spark Plug on The Rear Spark Plug on Passenger Side. NOTE: Drivers Side Spark Plugs on the Drivers Side Front to Back are Your Odd Numbers 1-3-5-7 Pasenger Side is Your Even Numbers From The Front is #2-4-6-8 Is The Rear PLug .

Heres a Diagram of your Spark plug Positions

Front of Engine
1 2
3 4
5 6
7 8

Hope This Will Get You Going. Let me know The Quality of Help and Solution I've Given You By Voting on It.And May Can Also Send a Testamony
From d_hubbs

Jun 03, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I TO KNOW HOW TO GET THE SPARK PLUGS OFF AND WHERE THE OIL FILTER IS LOCATED. I CAN SEE THINGS THAT RESEMBLE SPARK PLUGS BUT I CANT SEEM TO GET THEM OFF. ALSO THE NEW PLUGS I GOT FROM REPCO HAVENT GOT THE...


spark plugs do not come with wires you have to purchase them separately you have to remove plug wires one ata ime and then remove plugs but make sure you mark each wire as to which plug you removed it rfrom and also when removing from distributor cap mark the wires there as well

Dec 22, 2009 | 2003 Toyota RAV4

1 Answer

The destributor cap was loose, engine was running ruff, replaced cap, tuck running fine. After 100 miles it is running ruff again and check engine light is on. I found a hose around the destrutor cap,...


When's the last time you replaced the spark plug wires? Try that for you mis-fire. As for the vacuum hose, there should be a routing diagram somewhere on the hood or engine compartment somewhere. Trace it out and find where it should go. Oh BTW, bad spark plug wires can ruin a distributor cap.

Jun 30, 2009 | 1997 GMC Jimmy

1 Answer

Saturn 1996/ no spark


the crank sensor will not set a code. sensor is located on back side of engine block and is difficult to get to without a lift. my money is on the crankshaft sensor. let me know.

Dec 29, 2008 | 1996 Saturn SW

Not finding what you are looking for?
2003 Kia Sedona Logo

748 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...