I try to put it into 4wheel dr or low as normal and now i just get a click light flashes and it reverts back to 2wheel dr I also try going to neutral and the same result any answers please

If you are attempting to put into 4wheel low range, truck must be placed in natural first. Then push button for low range.

Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

On these issue,there are few solved help links for troubleshooting the issue easily.-------

Click the link below:---
No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

-----------
4X4 Truck makes roaring noise in the front end?

http://schematicsdiagram.blogspot.com/2012/01/4x4-truck-makes-roaring-noise-in-front.html

-------------
Car will not go into 4WD high or 4WD low?

http://schematicsdiagram.blogspot.com/2011/12/car-will-not-go-into-4wd-high-or-4wd.html

--------------
No 4x4 light on dash?

http://repairhelpcenter.blogspot.com/2011/12/no-4x4-light-on-dash.html

------------
4 wheel drive system will not disengage?

http://technoanswers.blogspot.com/2012/01/4-wheel-drive-system-will-not-disengage.html

----------
4WD light is flashing and beeping? NO 4WD high?

http://schematicsdiagram.blogspot.in/2012/02/4wd-light-is-flashing-and-beeping-no.html

----------
2002 Jeep Wrangler: 4WD Idiot Light is ON?

http://technoanswers.blogspot.in/2012/06/2002-jeep-wrangler-4wd-idiot-light-is.html

----------

Traction control switch will not engage on 4WD High or Low

http://whoisbyme.blogspot.com/2012/10/traction-control-switch-will-not-engage.html

-----------

4WD light flashing and 4WD will engage after few minutes

http://repairhelpcenter.blogspot.com/2012/10/4wd-light-flashing-and-4wd-will-engage.html

------------
2008 Toyota Tundra: 4x4 Wheel Drive Light is Flashing?

http://technoanswers.blogspot.in/2012/05/2008-toyota-tundra-4x4-wheel-drive.html

----------
4x4 front differential will not engage the axle on ford?

http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

-------
4x4 will not engage on Ford F150? http://technoanswers.blogspot.in/2012/02/4x4-will-not-engage-on-ford-f150.html

-------------
Dodge Ram 4x4 light keeps flashing 4X4 LOW LIGHT IS FLASHING ON DASH

http://technoanswers.blogspot.in/2012/09/dodge-ram-4x4-light-keeps-flashing.html

----------
Ford 4x4 front wheels will not engage?

http://technoanswers.blogspot.in/2012/02/ford-4x4-front-wheels-will-not-engage.html

-------------

These details will help.

Thanks.

you cannot run your truck normally in 4x4 low!!!! the low is designed to go slow slow.try shifting into neutral gear on column tap the high 4x4 then shift to reverse,back up 15feet then shift to drive.it should go into high 4x4 then if you want to go back to 2wheel high shift to neutral tap the 4x4 high until the light goes off,shift to reverse and back up 15feet then shift to drive and the 4wheel drive lights should all be off. then you'll be in 2x2 rear wheel drive. thank you for choosing fixya.com

does it have auto hubs, if so check the vacuum switch at tranny side

If you need further help, I’m available over the phone at https://www.6ya.com/expert/david_4c166ba81493f541

It is the shift motor for the 4wheel drive - only problem is that a shop has to program the new shift motor to the blazer or it will keep doing the same thing

the vacuum lines run to the hubs behind the brake rotors on the front wheels

it sound like it is going in to 4low rang but it may only be low 2wheel power brake it a little on dirt if the tires sin in the rear it was only low ranged 2 wheel u can get this by putting it in 4low and unlocking the hubs it may be a hub prob as it is common

this is common on these trucks just put your witch in 2 wheel and go ahead and drive it will let loos when it sees the correct secquence and drive a little and shift to netural.
just neve do it from high to low range