Question about 2006 Mercedes-Benz CLK 500

1 Answer

Abs and bas lights comes on and displays take to work shop,i can still drive the car. i have a 2001 clk 430 with 67, 120 miles on it

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 61 Answers

Need more info-possible bas diaphragm switch gone bad.does the fault occur as soon as you turn on the car or as soon as you step on the brake pedal??

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yesterday the Brake light and the ABS light stayed on when I started up my car (2001 Jimmy). I drove it home from the store (approx 3/4 mile) and parked it. Later I started the car up and the lights did...


yes its better to go shop and check what is the code so that u can easy to diagnose and repair..some problem of the abs light come in out is some abs defective or loose ,,or the abs motor ssy have problem or sensors in the wheel.

Aug 30, 2010 | 2001 GMC Jimmy

1 Answer

ABS light on


check fuse ,relay , wiring and connections for abs system usually a problem with a sensor wire which are located behind wheels something kicking up from the road if good have vehicle scanned some auto stores such as auto zone / advanced auto do it for free the trouble code will give you a start point for your problem

Nov 12, 2009 | 1998 Mercedes-Benz CLK

1 Answer

320 clk -98 what is the selusion when Bas-ESP-ABS is showing on my display? even the autodrive function is not working. Jesse


ABS--BAS

Most likely cause is the 'stop lamp switch'
It is a electric switch located on the brake pedal inside the car, about half way up on the brake pedal.
Pretty cheap too, I think the switch is only like $25 bucks.
2 connectors on the switch and then it turns out.
hope that helps

Jul 10, 2009 | 1998 Mercedes-Benz CLK

1 Answer

2002 CLK 320 convertible - Son installed battery in wrong - Burned up alternator, blow fuse on radio and amp. A week later radiator fan doesn't cut off. I replaced alternator and radio fuses. Purchased...


ABS--BAS

Most likely cause is the 'stop lamp switch'
It is a electric switch located on the brake pedal inside the car, about half way up on the brake pedal.
Pretty cheap too, I think the switch is only like $25 bucks.
2 connectors on the switch and then it turns out.
hope that helps
Fan relay should be in black box near frewall

Jul 10, 2009 | Mercedes-Benz CLK Cars & Trucks

1 Answer

The ABS ,BAS& ASR lights keep coming up


ABS--BAS

Most likely cause is the 'stop lamp switch'
It is a electric switch located on the brake pedal inside the car, about half way up on the brake pedal.
Pretty cheap too, I think the switch is only like $25 bucks.
2 connectors on the switch and then it turns out.
hope that helps

Feb 25, 2009 | 2001 Mercedes-Benz C-Class

1 Answer

04 clk320


well.. the output speed sensor is the output side of your transmission speed sensor... these are horrible on merc's... easily replaced... but a pain to get the correct one.. and this sensor could cause almost all the problems you list alone... but with such low miles it may be a warranty item? as it is on your transmission...

Sep 16, 2008 | 2004 Mercedes-Benz CLK-Class

2 Answers

1999 mercedes benz clk320


hi there it sounds to me like the brake calipar is either loose or the brake pad has separated and if this happens it will also damage the abs sensor

Aug 28, 2008 | 1999 Mercedes-Benz CLK

1 Answer

Clk 230 k


Check your ABS sensors. One is likely bad.

Jul 07, 2008 | 2000 Mercedes-Benz CLK

1 Answer

BAS ASR problem


ok, first you have to clear the codes.
in this type of cars you cannot clear codes with a regular obd II it has to be the factory scanner or similar. after you clear the codes drive it for a while. when light comes back on scan it again and that is going to be your true problem. if you replaced the switch but didn't clear the code the light will be still on because the computer doesn't know that you fixed the problem. so try it out and let me know if worked.

May 15, 2008 | 1998 Mercedes-Benz CLK

Not finding what you are looking for?
2006 Mercedes-Benz CLK 500 Logo

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...