Question about Triumph Tr 7

1 Answer

New rotor arm has broken immediately: am I using the wrong new rotor arm or is there an inhere4nt problem with the ignition system car Triummph 2000 (1964) couldn't choose from drop down menu for some reason! rotor arm used intermotor 47560 rotor arm removed 418726

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 272 Answers

It could be that you bought the wrong rotor. You said you removed a 418726 rotor, do you know the makers name for this rotor? If so your supplier can cross check across to supply the correct rotor. Also you can take the 418726 rotor to your supplier and tell them that this is the one you removed from the car. It may be that some one has changed the distributor in the past. In future when buying parts, try and take the old parts with you to help stop any confusion.

Posted on Nov 30, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 2000 ford 1ton super duty v 10 van turns over but wont start whats wrong, thank you johnny barcelon

There is two immediate reasons why a car won't start.
One will be gas the other one would be the ignition system,
Try spraying some starting fluid by the air filter see if it starts, if it does you have a fuel problem, if it doesn't you may have an ignition problem.

Sep 11, 2017 | Ford Cars & Trucks

1 Answer

Why the rear wheel bearing on a 2000 ford f 150 got broken its new

You need a trained Ford tech to look at this, it is impossible to know what is wrong without seeing the parts in question and doing a detailed inspection.

Apr 22, 2016 | Ford Cars & Trucks

1 Answer

2000 Chevy express Van 4.3 motordistributor cap and rotor new friendship position sensor new coil and its mission module our new still no spark

If the ignition coil, crank sensor,ignition ,module ,cap and rotor are new then possibly a bad pick up coil inside the distributor bad ignition coil wire from dist. to coil or missing power supply

May 02, 2015 | Chevrolet Express Cars & Trucks

1 Answer

How can i get my alarm to stop going off and dis arm it without un hooking my battery without using my remote since my theft system/ auto starter is outdated without going to the shop. 2000 pontiac...

most aftermarket alarms have a valet button and in the case of lost or broken key fob the button can be held or pressed when the ignition is turned on the turn alarm off. if it is a factory installed system usually opening driver door with the key will disarm it

Jun 05, 2011 | 2000 Pontiac Grand Prix

1 Answer

Car wont start has new everything plugs wires cap rotor battery ignition coil oxygen sensor fuel filter

I suggtes check of the "theft system" was armed when disconnected the battery; also check the roght order at firing sparkplugs.

Feb 07, 2011 | BMW 528 Cars & Trucks

1 Answer

Distributer rotor arm does not spin when the engine is cranked

Broken timing chain/belt will do the same thing.

May 08, 2010 | 1989 Subaru Gl Wagon

2 Answers

Will turn over but not start

1 see if you are getting spark 2 if not ecm is bad, or cap,or distributor 3 if yes timming is off hope this helps

Apr 14, 2010 | 2000 Mitsubishi Diamante

4 Answers

Theft system armed

disconnect your battery wait 30 seconds then reconnect and it wll start for sure. if not get a new or clean your old key and make sure it is dry then try again. I have dealt with this a hundred times an think it has to do with worn chips on the keys/bad sensor in the ignition.

Oct 08, 2008 | 1995 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

500 Answers


Level 3 Expert

79847 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides