Question about Suzuki Aerio

Open Question

Broken key in ignition

Hi , my key broke in my ignition and need to find out how to remove the barrel. I have already taken off the casing. I have a Suzuki Baleno. Thanks.

Posted by on

  • Joro R Mar 27, 2009

    broken key in ignition Suzuki Esteem 1999

×

6 Suggested Answers

hemantraj
  • 638 Answers

SOURCE: broken ignition barrel ford laser 1989 model

you your self can do it its simple do not call an technician. i will definatly guide you just let me know from where it is exactly broken.

Posted on Jun 15, 2008

  • 3422 Answers

SOURCE: broken ignition barrel ford laser 1989 model

Hi,

this is the procedure to remove the ignition barrel:

Remove the steering column surround and you should see a black round thing on the left hand side, this is the ignition switch. Remove this and you will see there is one screw holding the ignition barrel on, remove and you then need to insert your key and turn it to the ACC position. you should now be able to withdraw the barrel using the key but take care not to snap the key off in the barrel.

Please don't forget to rate or accept the solution as fixya.

Goodluck..

Posted on Jun 15, 2008

95zcvtecsi
  • 26 Answers

SOURCE: transponder key

ex my honda civic had a transponder key at one time, but some body cut the wires behind it and it still runs. what happend to the old key and did you buy this one at the dealership?

Posted on Aug 04, 2008

  • 135 Answers

SOURCE: I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING

it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

Posted on May 20, 2009

  • 4 Answers

SOURCE: mercedez 190 ignition barrel. I have taken out ignition barrel attached to steering coloum but i can not remove key ignition from steering coloum how does it remove ignition barrel from steering

Should be the same as w123 model. Check diy Mercedes web page.
Photos included easy to do.

Posted on Jul 07, 2009

  • 198 Answers

SOURCE: Engine pinning when accelerating only on cold Suzuki Baleno

Carbon build up on pistons raises engine compression.This is normal.Go up one grade on gas and/or put some fuel additive.If this doesnt solve it,have timing belt/chain inspected may need replaced

Posted on Sep 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My key broke off in ignition. What do I need to do in order to change ignition?


have a locksmith remove the barrel of the lock and fit a new barrel that is tumbler coded to the existing barrel. That way your spare key will still be encoded for the immobiliser.

Jul 28, 2014 | Cars & Trucks

1 Answer

Ignition switch


hi. its very unlikely that you will ever remove the broken key from the barrel. your best bet is to replace the barrel complete with key. from a breakers yard.

Mar 28, 2014 | Toyota Cars & Trucks

1 Answer

Wrong key broke off in ignition of a 2004 focus how do i removed this piece


Might have to have the barrel drilled out and replaced, I have removed broken keys with very fine crochet needles and a lot of patience. To take a barrel out without damage the key needs to be turned into the first position to depress the barrel lock pin, which you can't do with the broken key in. Good luck

Jan 23, 2014 | 2006 Ford Focus

1 Answer

Key broke in barrel needs barrel out with the broken key 2004 freelander


remove the cover round your ignition you need a torch to see a slot in your lock push a small flat head screwdriver in the slot but you need to be able to then lift out the cylinder. you would normally do that with your key in the barrel.

Dec 23, 2013 | 2002 Land Rover Freelander

1 Answer

A key broke off in the ignition. i need to know how to remove the ignition switch cylinder


Hi Once the cowling around the ignition is removed, turn ignition switch to the first position (because the key is in the switch you should be able to rotate to the first position)
On the top side of the ignition barrel there is a spring loaded pin ( this pin is difficult to see and get at)
When you have located this pin press it in ( use the cranked end of an alen key )
While its pressed in pull out the ignition barrel with the broken key in it
when you have the barrel in your hand you will be able to get broken key out.
All the best with this problem

Mar 06, 2011 | 1994 Ford Escort

1 Answer

The key has broken in the ignition and the lower section of key is stuck in the barrel. The car still starts and runs . How do i remove the broken section of key from the ignition barrel, I have removed...


on the left side of barrel, look for a dowel, there should be a vary small opening that you can take something as small as a pinhead and push the dowel in ,while pushing in on dowel pull the barrel out.the key may need to also be in on position for removal. try that and see if it works. if not please repost your question. thank you for choosing fixya.com

Dec 30, 2010 | Suzuki Esteem Cars & Trucks

2 Answers

Broken key in ignition


you can only push this detent pin in when ignition is in on position try to put key that snapped in and wriggle it around to try and turn ignition to on position so then you can remove barrel
if cant turn need to change whole assembly by un doing shear pin for clamp that holds whole assembly on steering column or do what some lock smiths do drill out old barrel slowly and going up in drill sizes until barrel comes out from housing without damaging housing

Jun 29, 2009 | 1992 Chevrolet Corsica

1 Answer

I HAVE A MERCEDEZ 190 AND THE KEYS ARE NOT TURNING IN IGNITION BARREL NOW THE STEERING IS LOCKED ALSO I HAVE TAKEN OUT IGNITION BARREL WITH STEERING COLOUM. i WOULD LIKE TO DISINGAGE THE IGNITION BARREL...


it is better to buy a new ignition barrel.it takes a special socket to get the screws out, once the screws are out they do not need to be replaced.buy new barrel,disconnect negative battery cable,disconnect wires from barrel assembly, remove barrel from colum. first take vin# to dealership parts department to get correct barrel assembly, the keys with new assembly will fit doors and trunk

May 19, 2009 | 1993 Mercedes-Benz 190

7 Answers

Ignition lock cylinder replacement


The key doesn't turn at all. Not even one click!!! the tumblers are completely jammed. I also just bought the Bently service manual but they don't offer a solution to my problem. I have been searching the web for days and at this stage I know I have only one of two solutions: to drill a small hole where the entry for the pin should be if the key would've turned, then use a pin to remove it; or drill straight through the center of cylinder to destroy the lock tumblers and then turn it to line up with the pin hole, and use the classic method to remove it. Before I attemp either, I need to know if anyone tried them and which one will work better or work at all? I already ordered a new cylinder from dealer so the problem is in removing the old one. Help please.

Aug 20, 2008 | 1996 BMW 318

2 Answers

Hi I have broken my only key in the ignition this morning Dont know how to fix or costs ,please could you advise.Thanks


hi there if your key has broken in the barrel you might be able to get it out with a strong magnet or a pin if not you will have to take the barrel out and strip it down if its broken at the **** of the key you may only need that peice and take it to timpsons they can cut you a new one. If the key is broken further towards the tip you will need both parts and a key cutter will still be able to cut you a new one hope this was a wee bit of help to you

Jul 20, 2008 | Suzuki Swift Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

401 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...