Question about 1998 Honda Accord

1 Answer

Axle replacement - 1998 Honda Accord

Posted by on

  • Anonymous Dec 16, 2008

    how do you remove the front axle?

  • floydbbrownj May 11, 2010

    what model car

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 34 Answers

There is a clip on the inner axle spline that holds it in the tranny, the best way is to remove the tire,axle nut, and lower ball joint. The outer should come free when you push the knuckle foreward or backward. then you need 2 big screwdrivers or prybars and put them between the tranny and axle, one on each side and push equally. it is tight but will come out. Thanks

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 f150 front axle to diff. seal replacement


OK, you must remove the front axle assembly to access the axle flange and then the seal, follow the instructions at the link but once the axle is out remove the axle flange from the front diff and replace the axle seal, use a seal driver and lube the new seal with lithium grease (white grease). You will need an air impact to get the flange nut off, replace it with a new one (do not reuse) and do not over tighten it. Cinch it down and then go about 1/8 more of full nut rotation to preload carrier bearing setting then spike in place. Ford F150 Front Axle Replacement Part 1

May 19, 2016 | Ford F-150 Cars & Trucks

1 Answer

How to replace 2006 ford escape left front axle shaft


How to Replace a CV Axle on a Ford Escape / Mazda ...

? 9:41
https://www.youtube.com/watch?v=_JxagNLBlQ4
Aug 29, 2013 - Uploaded by klowny1969
Axle nut should be torqued to spec..in the ford escape its around 205-220 lbs ft How To Change An Axle On A Front Wheel Drive Car ! SUBSCRIBE ! ... How to Replace a Front Axle Half Shaft - Duration: 14:37. ... Alternator replacement 2005 2006 Ford Escape 3.0L DOHC All Wheel Drive - Duration: 13:15.

Front axle replacement Ford Escape 2003 Right front CV ...

? 8:46
https://www.youtube.com/watch?v=JQK8SPj6Qsk
Mar 29, 2014 - Uploaded by Fixing cars and stuff
Front axle replacement Ford Escape 2003 Right front CV axle install remove replace This Channel provides ...

Feb 03, 2016 | Ford Cars & Trucks

1 Answer

Can i replace the hub and axle in one piece only for the fact that my axle nut is damaged can i pull the axle out of the the transmission and replace the hub and axle I've already replaced pass front axle


The hub needs to be removed from the axle in most cases for the axle to be removed from the vehicle. If you are replacing the axle anyway, you could cut off the end of the spindle with a cut-off disc on a grinder. That way the hub can come off and you can remove the axle. Hope this helps.

Feb 16, 2014 | Cars & Trucks

2 Answers

Have a 1997 plym voyager 2.4 auto trans with a trans leak where driver side axle bolts to tranny


the axle just slides in at that spot there is a seal there you will need to pull axle out and replace seal

Mar 12, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

How do you remove the rear hub nut on a 2004 ford f450 need to get to axle seal


Remove the bolts or nuts at the end of the axle and remove the axle from the axle tube. There will be a little gear lube that will come out that you will need to replace before you use the vehicle again after you replace the wheel seal. That will expose the axle nuts to the axle hub that you will need to remove to replace the inner wheel seal. It's basically very simple once you get the axle out you will see how it all comes apart. Be sure to torque the axle nut and locking nut correctly upon reassembly.

Dec 31, 2010 | 2004 Ford F150

1 Answer

How do you change the rear wheel bearings on a 2004 chevy express 1500 van?


Axle Shaft Bearing & Seal Removal & Installation To Remove:
  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Oct 18, 2010 | 2004 Chevrolet Express

3 Answers

How to replace rear Axle seal on 4x4 chevy


this is very hard if you do not know what you are doing. Ill try to step you through this
  • pull wheels
  • drain pun-kin case
  • pull rear cover
  • in between the spider and axle sets pull C ring with needle nose pliers
  • pull hub and axle out CAREFULLY as there are roller bearings on the end of the axle housing
  • pull seal out at the end of axle housing
  • tap in new seal CAREFULLY and straight DO NOT BEND IT or it will be junk
  • replace axle carefully as the roller bearings are still there
  • replace C clip to original position
  • replace axle diff cover and replace the gasket with a new one
  • refill diff case
  • install tire
  • your good to go

May 03, 2010 | 2002 Chevrolet Silverado

2 Answers

Mechanic says i need new front axles......


Usually once the boot is torn, dirt goes in, and all of the lubricant goes out. If you have been driving it this way, it will damage things faster. Normally you hear a "click" when turning out of a bad cv joint.It is a safer solution to just replace both, but of coarse, not cheaper.

Aug 19, 2009 | 1992 Honda Accord

1 Answer

83 cj7 rear axle


You could weld the keyway and file it back to size or replace axle. To upgrade, check with some of the big axle manufacturers like strange engineering etc. They could likely help or point you in the right direction. Anything you do will be $$ though.

Feb 22, 2009 | 1984 Jeep CJ7

1 Answer

Rear Axle Repair/Replacement


Unless the axles are somehow damaged all you will need to replace are the axle seals and the brake shoes themselves,

Aug 14, 2008 | 1999 Nissan Pathfinder

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...