Question about 1994 Mazda 323

Open Question

Mazda remote alarm key fob

Hello, I was wondering if there is solution to the problem that I have with the remote control unit I have for my car. Mazda 323f se W reg. (W 262 OES) Year: 2000 1.8 16V I recently had to purchase a replacement remote for the car as after replacing the battery in the original it failed to operate. When I received the replacement I was given a code to enter (a sequence of instructions to follow) these also failed to operate the system See instructions below) 1. Make sure the drivers side door is open.
2. Turn Ignition ON, and then back OFF.
3. Remove the key , and then repeat steps 1-2 2 more times.
4. Press the light switch that operates the courtesy light on the drivers
door A
post, and make sure the light goes out. Repeat this 2 times.
5. When the car makes a beep sound, press the Lock button on the remote
control 2 times, the car should make a beep sound.
6. Repeat for additional remote. Any advice you can give me is very much appreciated Thank you Mr. Derick Mcdonald

Posted by on

6 Suggested Answers

  • 541 Answers

SOURCE: How to remove door card on MX5 (2002)

Get a trim removal tool to use in pulling the door panel off. You will have to remove the screws under the arm rest as you find them. I would start at the bottom of the door and work up. You may want to assume that the work will progress better if the window is down before you begin. Mind the door handle as you remove things as the biggest complaint I've seen is that it fails to work right on the first try after getting things put back. Keep a magnet that has a telescoping arm handy to pick up things that fall to the bottom of the door. To remove window crank handles if you have them, put the trim tool behind the handle and engage the wire clip to remove it.

Posted on Jan 08, 2009

  • 141 Answers

SOURCE: 2006 mazda 3 dash light will blink

Wonder if it is a reminent of an old security system? Rather than taking it out and leaving a hole and wire splices, they just left the armed light there. Just a thought though. Do you have an owners manual? If so, check through it and see if there is a light, that is supposed to be there. Best wishes to you.

Posted on Jan 26, 2009

  • 1 Answer

SOURCE: programming keyless remote

2003-04 Mazda 6 REMOTE PROGRAMMING


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the driver’s door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the driver’s door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1 twice. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) twice. Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks. You're done!

Good Luck.

Posted on Jul 10, 2009

  • 396 Answers

SOURCE: I have the following problems on my 2000 Mazda

1 and 2 may be related. This is dangerous, and the repair is likely not a do-it-yourself thing.

Get it to a repair shop pronto.

Posted on Oct 14, 2009

bbbman78
  • 680 Answers

SOURCE: 96 mazda mpv minivan 165k mi. Ran fine until one

I was browsing unsolved problems. If you still have the problem, I'll try to help you. But it's going to be awhile trying to communicate back and forth. First...Check the engine for spark. Take off a plug wire and stick a screw driver in the wire end and place the metal part of the screw driver next to something on the van that's metal. Have someone crank it over for just a second or two and see if a small spark jumps from the screw driver to the metal part. I'll check back for your answer.

Posted on Mar 15, 2010

  • 5370 Answers

SOURCE: i have a 2003 mazda 6 1.8TS. the remote central

You mentioned you tried re-programming.So did you tried this procedure.If not,then try this procedure of reprogramming:--- The programming for a remote is as follows.

1. Open drivers door and leave open.
(in the uk that's the passenger side)
2. Lock and Unlock the drivers door using the power lock switch on door panel.
3. Insert key into the ignition.
4. Turn key to the ON and OFF position 3 times in 10 seconds. Leave key in ignition.
5. Open and close drivers door 3 times ending with door in the open position.
6. Door locks should respond by locking and unlocking.
7. Press any button on remote 2 times. Doors should then lock and unlock.
8. If programming a second remote press any button onit 2 times and door locks should lock and unlock.
9. Remove key from ignition and locks should lock and unlock again.
10. Test Remotes.------------------------
In some cases disconnecting and reconnecting the battery helps.Disconnect the battery for 15 minutes then reconnect the battery. ---------- Check out.Keep updated.Thanks.Helpmech.

Posted on Feb 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mustang alarm


Ford sold a Ford branded alarm through the parts department. These sometimes were a dealer installed option on new cars. Mine would randomly stop responding to the remote and I would have the same symptoms as you describe. I had it removed and the original equipment factory system still worked. Be warned, if you have the Ford "accessory" alarm, your key fobs (remotes) are different and the method to program them is different from what you will read online. You can tell if you have the system by looking at your key fob. The standard Mustang key fob is a 4 button (lock, unlock, panic, and trunk). The accessory alarm uses a 3 button remote and clicking unlock twice would pop the trunk. I really wish I had a picture of the remote because there are 3 button Ford key fobs for cars without a trunk release although I don't think you should have one on a Mustang. Long story short, if you have the accessory alarm, you can solve your problem by having it removed but you will need new 4 button key fobs to remotely lock/unlock your doors

Apr 04, 2014 | 2003 Ford Mustang

1 Answer

Remote Control


the fcc is a red herring. (its just a fed. radio lic. to use this freq.)
what is your question?
you lost your 2nd fob that came new with car?????
want a new fob?
the toy, dealer parts list for this part, is on the toy site, you look and see it and see the p/n of the fob and then find one. (google p/n)
and get it programmmed.

http://www.programyourremote.com/classified/DisplayAd.asp?id=1230


all google hits, in 5 sec.flat
http://blog.keylessentryremotefob.com/2013/07/2006-toyota-camry-key-fob-remote.html


need more, google more.

be happy you dont need 2 fobs to get 3 on a jeep , like mine.
be vary happy. ($400 worth of freakn keys)\

Jan 29, 2014 | Toyota Camry Cars & Trucks

1 Answer

Neither key fob is working to open the car with


open door. when alarm goes off put key in ignition and turn it on start car. this should disarm the factory alarm.

Feb 08, 2010 | 2005 Chrysler Crossfire

1 Answer

Key thob has stopped working, I have changed the battery but still broke, I am looking for the fuse for the central locking but cannot find it, saab 9-3 linear 2003


Saab's have very specific steps that you must follow when you change the batteries in your key fob. You might try these steps to re-sync your key fob to your security system....

If the battery has been changed outside the
car and the car is locked, proceed as follows:
1 Unlock the front left door with the traditional
key. If the car has a car alarm, this
will be tripped.
2 Open the door and insert the remote
control into the ignition switch. If the car
has a car alarm, this will be silenced.
The remote control and receiver unit are
now synchronized.

Jan 13, 2010 | 2008 Saab 9-3

2 Answers

Does my 2007 f 150 have a shock sensor that will trigger the factory alarm if a window is broken? If so how can I adjust it?


yes... on the unit itself. there is an adjustment screw you'll need to turn in one way or the other for sensitivity

Nov 03, 2009 | 2007 Ford F-150 Harley Davidson

1 Answer

I have a 1999 jeep grand cherokee. the alarm goes off whenever i open the door if the vehicle has been locked the alarm stops when i start the vehicle i only have a key, no remote any ideas on how to fix...


If ithe alarm is factory when they will have to reset the alarm module with a scanner. If the alarm if aftermarket go to the control module and see if it has a reset button. FOBs (remote) can reset alarm. You Jeep is always set for break-in mode. The FOB sets this when ever the FOB is used to lock the doors. May be bad alarm module - Sorry - Good luck

Oct 17, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Jag S-Type -intermitent fault where the remote fob does not work


This does not sound like a fob fault - but a locking control module fault , either in the hardware or software of the unit. Get it checked at a Jaguar dealers. When unlocking using the key - as soon as the door is opened you should hear a chime sounding inside the car - this is a timer counting down to sounding the alarm. If you put your key in the ignition as soon as you open the door the alarm should not go off and the chime should stop. If it does not this again points to a fault in the locking controller.
hope this helps - good luck.

Jun 22, 2009 | 2004 Jaguar S Type

1 Answer

Need programming instructions for RKE for 2000 Mazda 626


2000 Mazda 626
Note: Make SURE the battery is new.
Instructions for programming ONE keyless remote fob.
1. Open the driver’s door & leave open.
2. Insert the key in the ignition.
3. Turn the key to the on and off position 3 times.
4. Remove the key from the ignition.
5. After door open chime stops, press the door open button 3 times.
6. After chime, press any fob key twice.
7. After second chime, press any fob key twice again.
8. After third chime, press any fob key twice again.
9. Press the door open button once.
10. The car should give another acknowledgement chime.
11. Test key fob.
This DOES work. I just programmed mine successfully today, three hours ago.

Sep 03, 2008 | 2000 Mazda 626

Not finding what you are looking for?
1994 Mazda 323 Logo

Related Topics:

1,826 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...