Question about Dodge Ram 3500

1 Answer

The power windows seem to be in lock mode. None of the 4 will go up or down

Posted by on

  • Anonymous Nov 06, 2008

    you must not have ever looked at the manuel i have the same problem and the power outlet and sunroof do not work as well there is no fuse or power block that specifically states that it is for the power windows or sunroof or outlet any where in the fuse block or manuel or any other place i have looked need answer fast and i also have checked all the fuses and they are good

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Sounds like a power window relay or blown fuse. Most of these are located in the relay/fuse power center located under the hood. The lid will have a listing/diagram of which relays are for what purpose. Same goes for the fuses. The manual will have a location for that particular fuse.

Posted on Jul 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have power but none of the window go up or down


If you have power to the master switch, the switch it self could be bad. Usually the drivers window is the first to quit. the others work. If none are working, the window lock could be set or broken also. Stat with the drivers door window and manually apply power to the window motor. If it works fine replace the master switch

Oct 01, 2016 | 2001 Buick LeSabre

1 Answer

Window master switch seems like the window lock is stuck


Seems verry likly that the lock switch has stuck in the lock position and will most likly need to be replaced. Unless you are able to remove and spray with a contact cleaner

Nov 26, 2012 | 2004 Buick LeSabre

1 Answer

Power windows locks and mirrors


Sounds like the master switch is not plugged in properly, this is the switch in the driver's door.

Jun 07, 2012 | Cars & Trucks

1 Answer

Please Help _ None of the power windows work ona 1998 Cadillac STS. Checked the breaker under the back seat for continuity it's shows good. The power mirrors work fine and the rear window lock out


The windows are controlled through a computer module referred to as the BCM, it must be scanned to determine why it is not letting the windows operate.

Feb 12, 2012 | Cadillac Seville Cars & Trucks

1 Answer

A while ago my car started locking while the key was in the ignition (not in gear). Then later on it started re-relocking itself after i'd been in gear for a bit. I would just be driving and it would try...


hold down your lock button until the car chimes after it chime press it again 1 chime 1st mode, 2 chimes 2nd, etc. there are 4 modes you have to experiment and see which mode does what, or just consult your owners manual

Feb 26, 2011 | 2007 Honda Accord Sedan

1 Answer

My Fiancee rolled down all of her power windows in her 2006 toyota rav 4 to clean it and when she went to roll them back up, none of them would work except the drivers side


She must have hit the child proof lock switch, it is on the drivers side there, It should be the problem, If not, could she have splashed water down there? It might dry out and be fine. If not, I would check fuses, then pull the master switch and see what happened to it. It seems weird that it happened all at once. Gotta be something simple. Hope this helps.

Oct 05, 2010 | Toyota RAV4 Cars & Trucks

1 Answer

I am not able to use the hand held lock/unlock now. The driver door lock tries to work, but it won't. If I push the lock down manually, it will lock all locks. What could be wrong?


Note:
Entering the programming mode cancels all learned keyless remotes, so none of the
previously programmed remotes will work. You must reprogram all of the keyless
remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the
system from exiting the programming mode.

1. Turn ignition switch to ON (II)
2. Press the LOCK or UNOCK button on one of the remotes. (An unprogrammed
remote can be used for this step.)

3. Turn ignition switch to LOCK (0)
4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used
in step 2

5. Turn the ignition switch to ON (II)
6. Press the LOCK or UNLOCK button the same remote. Make sure the power door
locks cycle to confirm you are in programming mode.

7. Press the LOCK or UNLOCK button on each remote you want to program. Make
sure door locks cycle after you push each remote button to confirm system has
accepted the remote.

8. Turn the igniton switch to LOCK (0) to exit programming mode.
9. Test remote(s)

Mar 07, 2010 | 2002 Honda CR-V

1 Answer

Keyless remote


Note:
Entering the programming mode cancels all learned keyless remotes, so
none of the previously programmed remotes will work. You must reprogram
all of the keyless remotes once you are in the programming mode. You must complete each step within 4 seconds of the previous step to keep
the system from exiting the programming mode. You must program remotes
within 10 seconds of each other

1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes.
(An unprogrammed remote can be used for this step.)

3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote
used in step 2

6. Within 4 seconds press the LOCK or UNLOCK button on the same remote.
Make sure the power door locks cycle to confirm you are in programming
mode.

7. Within 10 seconds press the LOCK or UNLOCK button on same remote.

8. Within 10 seconds press the LOCK or UNLOCK button on all other
remotes you want to program. Make sure door locks cycle after you push
each remote button to confirm system has accepted the remote.

9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)

Dec 24, 2008 | 1998 Acura TL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

997 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...