Question about 2005 Ford Focus

1 Answer

Drivers door trim

Have got a rattle inside drivers door cant see how to get trim off dont appear to be any screws holding it on and i dont want to force it in case i break off any plastic bits

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

The handle part of the door panel comes pops off with a butter knife or screwdriver etc. and there will be one or two screws in there. Just be as gentle as you can cause sometimes it leaves marks in the plastic. Good luck!

Posted on Jul 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace interior passenger door handle on a 98 Buick LeSarbre?


There are screws hold the interior door handle onto the door. Loook for the holes on the bottom side of door handle. Or look for some removable trim and the screws are under the trim.

Oct 12, 2015 | Buick Cars & Trucks

1 Answer

How do i take off the inside drivers door panel on a 2005 dodge caravan


Hi Roberta, here's the instructions on how to remove your door panel. I have to wonder though on why you are removing it, my guess is you window doesn't roll up or down and your replacing the regulator. Any way here goes.

REMOVAL

  1. Remove the plug and remove screw attaching door pull cup to inner door panel.
  2. Remove switch bezel and disconnect power window/memory switch.
  3. Remove screws attaching trim panel to door from below map pocket.
  4. If equipped, remove window crank. (Refer to 23 - BODY/DOOR - FRONT/WINDOW CRANK - REMOVAL)
  5. Remove screw holding door trim to door panel from behind inside latch release handle .
  6. Disengage clips attaching door trim to door frame around perimeter of panel.
  7. Lift trim panel upward to disengage flange from inner belt molding at top of door.
  8. Tilt top of trim panel away from door to gain access to latch linkage.
  9. Disengage clip attaching linkage rod to inside latch release handle (INSIDE DOOR HANDLE LINKAGE).
  10. Separate linkage rod from latch handle.
  11. Disconnect the power door switch, courtesy lamp electrical connectors.
  12. Remove front door trim panel from vehicle.
Hope this helps and have an awesome day Roberta!

May 21, 2014 | 2005 Dodge Grand Caravan

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

I need to replce the drivers side mirror. Just seeking instructions on how to.


Remove front door handle bezel screw cover Remove inside handle bezel screw Remove inside handle bezel Lift upward on the rear of the front door inside handle bezel Disconnect electrical connector Remove handle screw cover
Remove handle screw Remove door trim panel upper screw Remove door trim panel lower screw Remove door trim panel (pull the door trim panel outward to release the pin-type retainers)Remove front door sail panel
Disconnect mirror electrical connector Remove 3 exterior mirror nuts and exterior mirror

agentyoel_0.png

Mar 07, 2011 | 2009 Ford Fusion

1 Answer

Can not remove side mirrors to be replaced


If the old ones wont come off, break them off. then look for hidden screws or clips for inside the door. But usually, you have to take the interior door panel off , and remove some trim to get to the bolts that hold them on. I have never taken one of those doors apart, but I know you will need an assorted Torx bit/driver set, some deep well sockets (around 1/4 inch. Usually the 1/4 inch drivers work fine), and a large screw driver/ pry bar. There are small plastic holders called "christmas trees" that hold the door panel firmly to the door so it wont rattle around. Just pry those little holders away from the door. if you break them, don't worry, they are really inexpensive at the auto parts store.

Aug 16, 2010 | 1997 Chevrolet Tahoe

1 Answer

Rattling noise(s)


remove front door window trim and place 3 or 4 beads of silicone adhesive on the inside of trim to hold it to the door frame. replace the trim and let the silicone cure overnite. It's a design flaw. I had the same problem, the dealer kept replacing it and it still rattled. After I put the sealer on it, I haven't had any noise for 35,000 miles. Good Luck!!

Apr 29, 2009 | 2007 Saturn VUE FWD 4

1 Answer

Rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln...


Rear
Removal
  1. Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
  1. Remove the two retaining screws.
  1. Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
  1. Disconnect electrical connectors.
Installation
  1. Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
------------------------------------------------------------------------------------ Rear
Removal
  1. Remove door trim panel and watershield. Refer to Section 01-05 .
  1. Check all connections of remote control links and cables. Service as necessary.
  1. Remove remote control assembly.
  1. Remove door latch remote control assembly from latch assembly.
  1. Drill out rivet at bellcrank and link (264B14).
  1. Remove three screws attaching latch assembly to door.
  1. Drill out rivet that attaches actuator motor to door.
  1. Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
  1. Install new bushings and clip onto latch assembly.
  1. Install latch with links and power lock actuator into door cavity.
  1. Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
  1. Attach door latch actuator motor to door with a new rivet.
  1. Install bellcrank and link to door using a new rivet.
  1. Install inside door handle and remote control assembly to door.
  1. Open and close door to check latch assembly operation.
  1. Install watershield and door trim panel. Refer to Section 01-05 .
ee8a11f.gif
Item Part Number Description 1 221A00 Door Handle to Door Latch Actuating Cable 2 26446 Rear Door Control Rod Retainer 3 377901 Plug Button 4 26412 Rear Door Latch 5 W623451-S2 Push Nut 6 224A32 Counter Balance 7 22450 Door Outside Handle Tension Spring 8 W701210-S309 Screw 9 224A20 Outside Door Handle Anti Rattle Pivot (2 Req'd) 10 22404 Door Handle 11 224A24 Front Door Outside Handle Spacer (2 Req'd) 12 264A64 Rear Door Actuating Rod 13 22408 Outside Door Handle Anti-Rattle Bumper 14 22428 Outside Door Handle Large Pad 15 N621906-S2 Nut (2 Req'd) 16 N807329 Screw (3 Req'd) 17 26595 Rear Door Electric Latch Actuator (RH) 18 W701566-S47 Rivet 19 431C04-A Rear Door Latch Striker Assembly 20 — Door Lock Striker Plate (Part of Door Shell Assy) 21 W525172-S Rivet (2 Req'd) 22 264B14 Bellcrank and Link (RH) 23 264A50 Bushing 24 N802034-SG Rivet 25 26420 Rear Door Latch Control Rod Link 26 W525172-S Rivet (2 Req'd) 27 21818 RR Door Latch (Inside) 28 A26460 RR Door Latch Push Button Rod 29 21982 Door Latch Rear Striker Assembly 30 N808377-S101 Screw (2 Req'd) 31 250A04 Rear Door Catch 32 N801010-S100 Truss Head Bolt (2 Req'd) 33 N804234-S2 Screw 34 266A74 Rear Door Latch Actuator Retainer 35 24630 Rear Door 36 26552 Rear Door Latch Control Escutcheon A — Tighten to 21-29 Nm (16-21 Lb-Ft) B — Tighten to 10-13 Nm (89-115 Lb-In) C — Tighten to 7-8 Nm (62-70 Lb-In) D — Tighten to 26-34 Nm (20-25 Lb-Ft) E — Tighten to 3-4 Nm (27-35 Lb-In)

Mar 24, 2009 | 1997 Lincoln Continental

1 Answer

2007 Vue door rattle


Remove the window trim at the rear of the front door. (There is a screw on the inside of the door frame at the top of the door. ) Place 3 or 4 thick beads of silicone adhesive on the inside of the trim piece. Don't put the adhesive on the alignment tabs. replace the trim and let the silicone cure overnite. I've had no problems for 35,000 miles since I did this.

Feb 19, 2009 | 2007 Saturn VUE FWD 4

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

1 Answer

325 ci conv


ok normally there are only a few screws or bolts that hold the door panel on sometimes they are located on the door handle on the inside somewhere or inside a small pop out panel on the door panel itself. Dont force anything because if you break any of the clips then you are in real trouble and have to either replace the clips or replace the door panel itself. just check and see if on the door handle has any screws or bolts. Most of the time there are just a few screws or bolts and a few clips. If there are clips try to pop them out really easy ok. If you have anymore questions just ask. I hope I helped

Aug 29, 2008 | 2001 BMW 325

Not finding what you are looking for?
2005 Ford Focus Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...