Question about 2004 Chevrolet Aveo

2 Answers

Fuel filter - 2004 Chevrolet Aveo

Posted by on

2 Answers

Behind rear passenger side tire

Posted on Oct 17, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Looking for the location of the fuel filter

Posted on Sep 12, 2008

  • rmatts1323 Sep 12, 2008

    looking for the location for the fuel filter

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is 2004 avalanche fuel filter


The fuel filter is contained in the fuel sender assembly inside the fuel tank. the paper filter element of the fuel filter traps particles in the fuel that may damage the fuel injection system. The fuel filter housing is made to withstand maximum fuel system pressure, exposure to fuel additives, and changes in temperature. There is no service interval for fuel filter replacement.

IMPORTANT: This vehicle has a lifetime fuel filter built into the fuel sender inside the tank and thus is not serviceable separately. The fuel filter is not a replaceable part.

Jul 15, 2014 | Chevrolet Malibu Cars & Trucks

2 Answers

How to change 2002 2.8 4bj1 fuel filter


your diesel engine should have a center bolt holding fuel filter it in place.you place drain pan under fuel filter when you remove top center bolt while holding fuel filter then remove old fuel filter then take new fuel filter add few ounces clean diesel fuel in new fuel filter lubricate gasket new fuel filter cartridge then install new filter crank engine check for leaks.

Nov 13, 2011 | Cars & Trucks

1 Answer

WHERE IS THE FUEL FILTER ON A 88 NISSAN PATHFINDER


Fuel Filter REMOVAL & INSTALLATION CAUTION
NEVER SMOKE WHEN WORKING AROUND OR NEAR GASOLINE! MAKE SURE THAT THERE IS NO ACTIVE IGNITION SOURCE NEAR YOUR WORK AREA! 1970-83 Carbureted Engines The fuel filter is located on the right inner fender in the engine compartment. It is a disposable cartridge type.
  1. Using a pair of pliers, expand the hose clamp on one side of the filter, and slide the clamp further down the hose, past the point to which the filter pipe extends. Remove the other clamp in the same manner.
  2. Grasp the hoses near the ends and twist them gently to pull them free from the filter pipes.
  3. Pull the filter from the clip and discard.
  4. Install the new filter into the clip. Push the hoses onto the filter pipes, and slide the clamps back into position. Start the engine and check for leaks. Fig. 1: Fuel filter - 1970-79 85851035.gif
    Fig. 2: Fuel filter - 1980-83 85851036.gif
1984-86 Carbureted Engines The fuel filter is located on the inside of the frame above the left rear spring front shackle. Changing the filter is VERY awkward. Since it is in-line and below tank level, fuel will pour from the fuel lines when they are disconnected from the filter. The only way of preventing this, is to siphon all of the gasoline from the tank before replacing the filter. Another possible method is to clamp and plug the fuel line, but this is not recommended because of the danger of leaking fuel or damage which could occur to the fuel line when clamped. It would, therefore, be a good idea to run the tank almost dry before changing the filter. Once the tank is dry, disconnect the fuel lines at the filter, unbolt the old filter and install a new one. Reconnect the fuel lines, fill the tank, start the engine and check for leaks. Fig. 3: Fuel filter - 1984-86 85851037.gif
Fig. 4: Remove the shield mounting bolts 85851162.jpg
Fig. 5: Remove the shield, if necessary for fuel filter removal 85851163.jpg
Fig. 6: Removing fuel filter - always replace fuel line clamps 85851164.jpg
Fuel Injected Engines WARNING
Never attempt to remove the fuel filter without first relieving the fuel system pressure!
  1. Release the fuel pressure from the fuel line as follows:
    1. Remove the fuel pump fuse at the fuse box.
    2. Start the engine.
    3. After the engine stalls, crank the engine two or three times to make sure that the fuel pressure is released.
    4. Turn the ignition switch OFF and reinstall the fuel pump fuse.
  2. Loosen the hose clamps at the fuel inlet and outlet lines then slide each line off the filter nipples.
  3. Remove the fuel filter.
  4. Replace the fuel filter. Always be sure to use new hose clamps. Fig. 7: Fuel filter - 1986-88 VG30i 85851038.gif
    Fig. 8: Fuel filter - 1986-88 Z24i 85851039.gif
prev.gif next.gif

Oct 17, 2010 | 1988 Nissan Pathfinder

1 Answer

Is there A in line fuel filter on A 2001 grand am 3400 and if so where is it


Fuel Filter Removal & Installation To Remove:
NOTE: There is no maintenance schedule for fuel filter replacement. Replace the fuel filter if restricted. Inspect the fuel tank internally if you find a restricted fuel filter.
Typical inline fuel filter gm-05-38-686.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Raise and safely support the vehicle.
  4. Remove or disconnect the following:
    • Quick connect fitting at the fuel filter inlet
    • Fuel filter outlet fitting from the fuel filter while holding the filter fitting with a back-up wrench
    • Fuel filter from the vehicle
    • Fuel line O-ring.
To Install:
  1. Position the new fuel filter in the bracket.
  2. Install a new plastic retainer on the fuel inlet line.
  3. Lubricate the new fuel pipe O-ring with clean engine oil.
  4. Install the fuel pipe O-ring.
  5. Reconnect the fuel outlet line to the filter by holding the filter with a back-up wrench and tightening the line fitting to 20 ft lbs (27 Nm).
  6. Lower the vehicle.
  7. Pressurize the fuel system and check for leaks.
prev.gif next.gif

Jul 12, 2010 | 2001 Pontiac Grand Am SE

1 Answer

Cant find where the fuel fillter is located in our pontiac Grand am 2004


Fuel Filter (behind gas tank) Removal & Installation To Remove:
NOTE: There is no maintenance schedule for fuel filter replacement. Replace the fuel filter if restricted. Inspect the fuel tank internally if you find a restricted fuel filter.
Typical inline fuel filter gm-05-38-686.gif

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Raise and safely support the vehicle.
  4. Remove or disconnect the following:
    • Quick connect fitting at the fuel filter inlet
    • Fuel filter outlet fitting from the fuel filter while holding the filter fitting with a back-up wrench
    • Fuel filter from the vehicle
    • Fuel line O-ring.
To Install:
  1. Position the new fuel filter in the bracket.
  2. Install a new plastic retainer on the fuel inlet line.
  3. Lubricate the new fuel pipe O-ring with clean engine oil.
  4. Install the fuel pipe O-ring.
  5. Reconnect the fuel outlet line to the filter by holding the filter with a back-up wrench and tightening the line fitting to 20 ft lbs (27 Nm).
  6. Lower the vehicle.
  7. Pressurize the fuel system and check for leaks.
prev.gif next.gif

Jun 30, 2010 | Cars & Trucks

2 Answers

How to change the fuel filter on a suzuki grand vitara 2.0td with RHZ engine


Fuel FIlter - Removal
  1. Relieve fuel system pressure.
  2. Remove or disconnect the following:
    Negative battery cable Fuel lines from the fuel filter Fuel filter
To install:
  1. Install or connect the following:
    Fuel filter and tighten the bracket bolt. Note the fuel flow directional arrow. Fuel lines to the fuel filter. Negative battery cable
  2. Start the engine and inspect the fuel filter connections for leaks.

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel lines from the fuel filter Fuel filter
To install:
  1. Install or connect the following:
    Fuel filter and tighten the bracket bolt. Note the fuel flow directional arrow. Fuel lines to the fuel filter. Negative battery cable
  2. Start the engine and inspect the fuel filter connections for leaks.
Fuel filter is incorporated in fuel pump assembly in fuel tank.

Hope this help.

May 15, 2010 | 2003 Suzuki Grand Vitara

1 Answer

Looking for fuel filter on 2004 chevy silverado ss 6.0, not on frame rail


Here is the steps for the removal and replacement...getting you the picture and location next. 6.6L Engine
  1. Disconnect the negative battery cables.
  2. Drain the fuel from the fuel filter as follows:
    • Install a hose on the water drain on the water-in-fuel sensor.
    • Place the other end of the hose into an approved container.
    • Drain as much fuel as possible from the fuel filter housing.
    • Tighten the water drain on the water-in-fuel sensor.
  3. Remove or disconnect the following:
    • Water-in-fuel sensor harness connector
    • Fuel filter from the fuel filter/heater element housing
    • Water-in-fuel sensor from the fuel filter

7f47ade.gif
Exploded view of the fuel filter (2)—6.6L engine

To install:
  1. Install or connect the following:
    • Water-in-fuel sensor in the fuel filter
    NOTE Check the fuel filter/heater element housing and the filter for a dislocated filter seal or foreign debris. Contamination on the filter/heater housing may cause leakage at the fuel filter. Coat the seal with clean engine oil.

    • Fuel filter on the fuel filter/heater element housing
    • Water-in-fuel harness connector
    • Negative battery cables
  2. Prime the fuel system:
    • Pump the primer located on top of the fuel filter 30 times or until stiff.
    • Try to start and run the engine. If the engine does not start, repeat the previous step.
    • Allow the engine to run for 5 minutes at idle.
    • Check for fuel leaks and clear all Diagnostic Trouble Codes (DTCs).

May 07, 2010 | 2004 Chevrolet Silverado 1500 Crew Cab

2 Answers

How to change fuel fillter


2002 Hyundai Sonata 2.4L MFI DOHC 4cyl the Fuel Filter is located uUnder vehicle, driver side, below seating area, driver side of fuel tank, mounted on frame in fuel line.


Hyundai Car 1999-05 - Removal & Installation

NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

d8227e1.jpg

Fig. Remove the fuel filter
  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.

Hope this help to solve your problem.

Apr 24, 2010 | Hyundai Motor 2002 Sonata

1 Answer

I need to replace my fuel filter. need to know where it is and what i need to do to access it.


Hi,

Regarding Fuel Filter - Under vehicle, driver side, below seating area, front of fuel tank, mounted on chassis in fuel line.

A device located in the fuel line to remove impurities from the fuel before it enters the carburetor or injector system.

INSPECTION

Fuel filters can be located in a fuel line, in the tank, in a carburetor, or in any combination of these. A carburetor often has a filter behind the fitting at its fuel inlet.

1ad2c35.gif

A carburetor inlet filter. Courtesy of General Motors Corporation, Service Technology Group. Fuel filters that are installed on the outlet side of a fuel pump are called outlet filters.

cb37d5e.gif

An external fule filter. Courtesy of General Motors Corporation, Service Technology Group. Engine heat causes fuel to vaporize, which can result in vapor lock in the filter. Some fuel filters have vapor return lines to allow for expanding vapors and fuel to return to the tank.

69cd470.gif


A fuel filter with a vapor return outlet. Courtesy of AlliedSignal Automotive Aftermarket. Fuel injection systems require larger, heavier duty filters than carburetors. They filter out smaller particles of dirt while still allowing the pump to supply a substantial amount of fuel.


REPLACE

Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
ef724eb.jpg


Disconnect the negative cable at the battery.

eb46ad8.jpg

Loosen the fuel tank filler cap to relieve any fuel tank vapor pressbae0f2b.jpga678067.jpg

Connect the fuel pressure gauge to the Schrader valve.

3b21ca2.jpg


Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.

Oct 08, 2009 | 1997 Chevrolet Malibu

1 Answer

How to replace fuel filter on a Mercury Village '95?


go here for help on villager issues

http://autos.groups.yahoo.com/group/villagerquest/

It's unde the hood, on the firewall, on the driver side.

Fuel Filters In-Tank
Removal and Installation
The in-tank fuel pump filter is not serviced separately. To service the fuel pump filter, replace the fuel pump (9350). Refer to the procedure in this section. In-Line
Removal
The following illustration is an exploded view of the fuel filter (9155).

c599850.gif
Item Part Number Description 1 9K299 Fuel Filter Upper Hose 2 9A335 Fuel Filter Bracket 3 — Fuel Hose Clamp 4 9C323 Fuel Filter Lower Hose 5 9155 Fuel Filter 6 — Fuel Hose Clamps
  1. Relieve the fuel system pressure. Refer to the procedure in this section.
  1. Remove the fuel hose clamps.
  1. Disconnect the upper and lower fuel filter hoses from both ends of the fuel filter. Plug the fuel hoses to prevent leakage and contamination.
  1. Remove the fuel filter from the fuel filter bracket (9A335).

Jun 05, 2009 | 2001 Mercury Villager

Not finding what you are looking for?
2004 Chevrolet Aveo Logo

Related Topics:

163 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...