Question about 1996 Toyota Corolla
My 96 Corolla has 187,00 Mi on the original motor. It drives great with the exception of when accelerating, at 3500 RPM the motot starts to cut and/surge in and out. If I back off of the accelerator to abou 3200 rpm the motor performs as always. any idea where to start and look.
I have the same problem but it happens sometimes at any RPM. I have tried the following and still no solution: There is no MAF on this years model.
changed spark plug wires
changed spark plugs
changed rotor cap
tried 2 different whole distributors
cleaned the fuel injectors
by passed the egr valves
even unplugged the car starter before these test in case it was a problem
Gas filter has been changed
Posted on Nov 11, 2008
Try the high tension wires. a car that old may have frayed the harness and at revs the electrical impulses may be jumping or maybe check the distributor cap for cracks.
Posted on Nov 09, 2008
Sounds like you need to replace the MAF sensor its the unit on toyota vehicles that calulates how much Air intake is going into the throttle body and then sends a signal to the ECU of your car which adjusts your Fuel injector compensation. When your MAF Sensor is malfunctioning it will throw the fuel curves out of wack and cause your car to what mechanics call "lean out" or "running rich" its basically your getting too little or too much fuel at higher RPM's and the motor is choking from too much fuel and not enough air. Hope this helps let me know if it doesnt so i can continue to troubleshoot for you via internet
Posted on Jul 21, 2008
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Sep 02, 2014 | Cars & Trucks
Feb 18, 2013 | 1993 Nissan Pickup
Engine cuts out at 3000 RPM? http://schematicsdiagram.blogspot.com/2011/12/engine-cuts-out-at-3000-rpm.html
Cold start problem and vehicle shudder around 2500 to
High rpm in neutral? Inconsistant high RPM in neutral? http://technoanswers.blogspot.in/2012/02/high-rpm-in-neutral-inconsistant-high.html
Jetski Sputters and Low RPM? http://whatisbyme.blogspot.in/2012/07/jetski-sputters-and-low-rpm.html
Fuel Injection Problem And RPM suddenly increases http://whatisbyme.blogspot.in/2012/07/fuel-injection-problem-and-rpm-suddenly.html
2005 Toyota Highlander: Engine runs hard RPM below 3000? http://whatisbyme.blogspot.in/2012/05/2005-toyota-highlander-engine-runs-hard.html
1987 Toyota Camry: RPM Drops going Up hills? http://whatisbyme.blogspot.in/2012/05/1987-toyota-camry-rpm-drops-going-up.html
Cruise Control stops working, Excessive cranks to start the engine and RPM goes max 2500 http://whoisbyme.blogspot.in/2012/07/cruise-control-stops-workingexcessive.html
1990 Toyota 4Runner: Engine cuts off when reaches 2000 RPM?
1999 Toyota Camry: Erratic stalling and high engine RPM at idle?
1995 Toyota LS: Misfire at idle or low RPM http://whatisbyme.blogspot.in/2012/04/1995-toyota-ls-misfire-at-idle-or-low.html
Lexus RX: Tapping noise under Valve Cover At Low RPM? http://technoanswers.blogspot.in/2012/04/lexus-rx-tapping-noise-under-valve.html
These will help.
Nov 22, 2012 | Cars & Trucks
Aug 26, 2012 | 1992 Chevrolet C/K 3500
Aug 09, 2012 | Cars & Trucks
Nissan Pathfinder Backfires? http://technoanswers.blogspot.in/2012/02/nissan-pathfinder-backfires.html
---------How to adjust rpm? http://schematicsdiagram.blogspot.com/2011/12/how-to-adjust-rpm-on-2009-dodge-charger.html
------------Engine cuts out at 3000 RPM? http://schematicsdiagram.blogspot.com/2011/12/engine-cuts-out-at-3000-rpm.html
----------This will help.Thanks.
Feb 17, 2012 | 1992 Nissan Pickup
May 10, 2010 | 1998 Ford Contour
Apr 26, 2009 | Pontiac Grand Am Cars & Trucks
Nov 12, 2008 | 1996 Toyota Corolla
364 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: