Question about 2003 Ford Crown Victoria

2 Answers

Crown victoria window motor replacement

How can I change a power window motor on a 2003 Crown Victoria?

Posted by on

  • 3 more comments 
  • Anonymous Mar 20, 2014

    blower motor defaulting to defrost

  • Anonymous Mar 21, 2014

    no dc power to anything

  • Anonymous Mar 23, 2014

    Where is the ecu crown victoria 2006

  • Anonymous Mar 23, 2014

    new blend door motor is there a reset for it

  • Anonymous Mar 23, 2014

    tem wot change after replacing blend door motor

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 28 Answers

Remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Pull the door panel then thers gona be a motor mounted there its gona be a tight squeze in the door there aint much room. hope that helps... JON

Posted on Nov 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does not come out through the vents in a 2003 crown victoria


There may be several reasons for your issue. Check here for some of the most important: blower vents not switching
It could be an actuator(motor) that stopped working.

Here is a list of Crown Vic part:
List Blend Door Actuator 2003 Ford Crown Victoria Reilly Auto Parts

Here's an example of what may need to be done in a similar situation:
If you are handy, possibly buying a repair manual similar to this may help:

Apr 08, 2016 | 2003 Ford Crown Victoria

1 Answer

1997 V8 4.6l. It turns over, but why won't it start?


Part 1 -How to Test the Starter Motor (Ford 4.6L, 5.4L)

troubleshootmyvehicle.com > Ford > 4.6L, 5.4L
Mar 2, 2011 - Page 1 of 3: How to test a BAD Starter (Ford 4.6L and 5.4L Pick Up and SUV). ... a BAD starter motor on your 4.6L or 5.4L V8 equipped car, pick up or SUV. ...and will turn over the engine; -OR-; The starter motor won't do a thing. ... Crown Victoria ... 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005.

Question: 1997 Crown Victoria Lx Cant Turn on and Cant ...

www.2carpros.com/.../question-1997-crown-victoria-lx-cant-turn-on-an...
May 26, 2014 - Ok so i put the keys in the car turn the key but seems to me it moves more ... 1997 Ford Crown Victoria • 4.6L V8 RWD Automatic • 99,625 miles ... Keywon't turn off accessories or turn car over and ignition cylinder turns too ...

Oct 19, 2015 | Ford Crown Victoria Cars & Trucks

1 Answer

Can an engine be rebuilt in a 2003 crown victoria police car


Yes it can, there are many parts around for a rebuild, even upgrade some parts, you can also rebuild your transmission too, even change gears. But you can also find used low mile engines around as well as a replacement , These are modular engines , Grand Marquis will work as well

Oct 04, 2014 | 2003 Ford Crown Victoria

2 Answers

How to get windows to go up and down in 1995 ford crown victoria


No up
No down
One window
All windows
Window fails down
You hear motor run & no window movement
You work the switches & they work sometimes

I would imagine you need that answered at a
repair shop

Feb 14, 2013 | 1995 Ford Crown Victoria

2 Answers

2003 crown victoria fuse box diagram


Here is the information you needed. I hope it helps and good luck....

11_5_2011_8_41_38_am.jpg
11_5_2011_8_42_06_am.jpg
11_5_2011_8_42_30_am.jpg
11_5_2011_8_42_49_am.jpg
11_5_2011_8_43_21_am.jpg

11_5_2011_8_43_59_am.jpg
11_5_2011_8_44_24_am.jpg
11_5_2011_8_44_46_am.jpg
11_5_2011_8_45_10_am.jpg
11_5_2011_8_45_28_am.jpg

Nov 05, 2011 | 2003 Ford Crown Victoria

1 Answer

Ford crown victoria


you must replace the multi fuction switch! also known as the turn signal switch! its common on ford crown vic!

Mar 06, 2010 | 2001 Ford Crown Victoria

1 Answer

1997 ford crown victoria window reulator and motor replacement steps


easy real easy.. go out to the local pull a part junk yard.. get a cross ref on your car.. find that car in the yard and tear it apart in the yard so that you can then later be able to do the same thing in your on ride.. all you need for tools is a walmart 30 piece set your good to go.

Oct 18, 2008 | 1997 Ford Crown Victoria

Not finding what you are looking for?
2003 Ford Crown Victoria Logo

2,496 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...