Question about 1999 Ford Mustang Cobra

1 Answer

Need wiring from spark plugs to cap 6 cylinder

Posted by on

1 Answer

Need diagram for 99 trinton spark plugs

Posted on Sep 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spark plugs and wires


It sounds like the spark plug wires are not plugged into the correct place on the distrubutor. take the distributor cap off and crank the engine over. Make a note of which direction the rotor spins. (Clockwise, or Counterclockwise) then find the firing order for that engine. Sometimes the firing order is on the intake manifold. (if you tell me which engine it has, the 4 cylinder 2.0, or the 6 cylinder 2.5; I could post you the firing order). Now on the distributor cap there is one wire post that has the #1 on it, that would be where you put the spark plug wire from cylinder 1. Following the rotation of the distributor rotor, you would put the spark plug wire for the next cylinder in the firing order after the #1 wire, and so on.

Dec 11, 2011 | 1998 Ford Contour

1 Answer

I have a 98 honda accord 5 spd it has a 4cyl motor vtech i just need to know how to fix a miss fire in cylinder 2 and wich one is cylinder 2


Cylinder #2 is the the second spark plug counting from the right to left.
EX.Below are spark plug on engine
engine
-------------------------------
' (oil cap) '
' (4) (3) (2) (1) '
'_________________'

Your misfire can be cause by couple of things but the cheapest way that you can try to fix your car is to do a tune up by replacing:
1)all spark plugs
2)do a oil change
3)spark plug wires
3)distributor cap and rotor

note misfire can be cause by:
1.bad gas
2.spark plug and/or wire
3.distributor cap and/or rotor
4.valve adjustment
5.injector
6.off timing
7.ECM
8.bad wiring(power, ground or feed line)

Jul 08, 2011 | 1998 Honda Accord

2 Answers

Change my spark plugs and distrubutor cap and the 85 ranger want start


You may have got the spark plug wires out of sequence.
Reseat the coil wire going to the center of the distributor cap Check the spark plug wires at the distributor against the firing order as follows:
The spark plug firing order is 1 - 4 - 2 - 5 - 3 - 6 The distributor rotor turns CLOCKWISE The engine cylinders / spark plugs are numbered :
firewall 3 - 6 2 - 5 1 - 4 front
Best wishes,
TF

Jun 03, 2011 | 1985 Ford Ranger

1 Answer

2001 dodge ram 1500 5.2 v8 van spark plug diagram


firing order is 1 8 4 3 6 5 7 2 standing in front of truck. cylinders on passenger side facing you are 2 4 6 8 cylinders on driver side facing you are 1 3 5 7 now this is your spark plugs wires location on distributor cap.with distributor facing you.2 plugs wire on cap 6 oclock position 1 plug wire on cap 8 oclock position,8 plug wire on cap 9 oclock position,4plug wire cap 10 oclock position,3 plug wire on cap 12 oclock position,6 plug wire on cap 1 oclock position, 5 plug wire on cap 3 oclock position, and 7 plug wire on cap 5 oclock position. in order for this to work you must be standing facing the engine all plug wire location on cap should be correct.

Apr 08, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

I need a wiring diagram for the ignition control module and distributor on a 2.8 litre v6 motor


OKAY STANDING IN FRONT OF ENGINE ON LEFT SIDE CYLINDERS FACING YOU IS 1 3 5 ON RIGHT SIDE DRIVER SIDE CYLINDERS FACING YOU IS 2 4 6 LOOKING AT DISTRIBUTOR CAP NUMBER 1 SPARK PLUG ON CAP IN THE 9 OCLOCK POSITION YOUR NUMBER 5 SPARK PLUG ON DISTRIBUTOR CAP IN 6 OCLOCK POSITION .STARTING AT NUMBER 1 SPARK PLUG ON CAP COUNTING CLOCKWISE COUNTING 1 2 3 4 5 6 THATS YOUR SPARK PLUGS WIRES ON CAP TO ENGINE PLUGS. 6 PLUG WIRE ON CAP IS AT 7 OCLOCK POSITION.

Feb 07, 2011 | 1988 Pontiac Firebird

1 Answer

How do you check the firing order on a chevy small block engine ?


Firing order for small block chevy is 1-8-4-3-6-5-7-2. The cylinders are numbered 1-3-5-7 on the driver's side of the engine counting front to back. Passenger side is 2-4-6-8, front to back. You will need to get #1 cylinder at top dead center on the compression stroke. To do this, remove the #1 spark plug and remove the coil wire from the distributor cap. You will need a helper for the next step. Place your index finger in the empty spark plug hole, Have your helper bump the starter with the ignition key, When #1 cylinder comes up on the compression stroke, the pressure will push your finger away from the spark plug hole. Don't worry, this doesn't hurt. Turn the key off. Check the timing mark on the harmonic balancer behind the crankshaft pulley. It should be pretty close to lining up with the "0" timing mark on the pointer attached to the engine block. Now pull the distributor cap and see where the rotor cap is pointing. This will be #1 on the distributor cap. The spark plug wire from the #1 plug will occupy that position. The next position on the distributor cap will be for the plug wire coming off the #8 cylinder. The rest of the plug wires will attach to the distributor cap in the above mentioned firing order counting clockwise. If you do not wish to place your finger in the #1 spark plug hole, you can use a piece of paper towel roll up and stuck in the hole just enough to form a seal. When the piston comes up on the compression stroke it will force the paper towel out. Any questions, just let me know.

Dec 30, 2010 | Chevrolet Chevy Cars & Trucks

2 Answers

I took of*** my spark plug wires working on my small block 350 pickup and I don't remember the the firing order to put the new wires back on. Is there a diagram anywhere or is it even that difficult to...


Next time number each lead before you remove it and no. the dissy cap as well

The firing order, which should be cast into the intake manifold, for the chevy small block V8 is 1-8-4-3-6-5-7-2. The firing order is the numerical sequence in which the spark plugs are fired. The insertion position of each spark plug wire around the circumference of the distributor cap can be found according to a clock face. The insertion sequence determines the firing order. The firing order is followed clockwise around the distributor cap starting from the 6:30 position with the 6:30 position being the number one cylinder spark plug wire.
On classic chevy small block engines that use ignition breaker points instead of electronic ignitions, the number one cylinder is the one immediately clockwise of the small metal sash cover on the distributor cap. The firing order starts here. There is no sash cover on the distributor cap for GM HEI electronic ignitions, and the firing order is the same, but starting at the 5:30 position.
The firing order makes sense if you know how the cylinders are numbered. The number one cylinder is the front most on the drivers side and 2 being the front most on the passenger side. From front to back, the cylinders are odd numbered on the drivers side, and even numbered on the passenger side.
See the diagram; Click to open a printable larger image in a new window. The firing order starts with the number one cylinder. We would connect the number one spark plug wire to the distributor cap terminal in the 6:30 position. distributor.pngSince the next cylinder in the firing order is 8 (passenger side rear), we connect the number 8 spark plug wire to the next distributor cap terminal (approximately 7:30 position) in the clockwise direction from number one. You need to be sure you continue the firing order in the clockwise direction around the chevy small block distributor cap from the last installed spark plug wire. Setting the rest of the firing order is just a matter of repetition. Be sure to count the spark plugs from front to back on each side of the motor to identify the correct cylinder number in the firing order.

Jun 21, 2010 | Cars & Trucks

1 Answer

Chevy 95 g20 van 8 cylinder wiring order spark plugs


1-8-4-3-6-5-7-2 The #1 spark plug is the front spark plug on the drivers side and the cylinder location in order from front to back on the drivers side is 1-3-5-7 and on the passenger side it is 2-4-6-8. The ignition rotor rotation is clockwise.

If your Distributor cap is not numbered then replace the new wires, or transfer the old ones to the new distributor cap one wire at a time. Identify the #1 spark plug wire and start from there.

Apr 23, 2010 | 1995 Chevrolet G20

2 Answers

What do these trouble codes mean po306 cyclinder misfire detected .how do i fix the problem?


it means you have a misfire on the number 6 cylinder

this could be caused by a whole lot of reasons.

start by inspecting for a bad plug wire if it has them

check for fire on the cylinder with a spark test tool from local part store

if it is a coil-on-plug set-up, check the coil for fire

replace coil/plug wire as needed, replace boot on coil if coil needed, replace spark plugs

Oct 11, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
1999 Ford Mustang Cobra Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...