Question about 2002 Chrysler Sebring

1 Answer

Rear stut moun

I am trying to find out if the rear mount has 3 nuts or 2

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

2 nuts and the big one is the center , dont loosen that one

Posted on Aug 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change rear wiper motor?


Step 1: Remove wiper arm.

Pull back the little plastic cover to gain access to the retaining nut. Loosen the nut until the threads are flush with the nut, and while pulling on the wiper arm give the nut a couple light taps with a hammer. Once the arm moves remove the nut and the arm.

Step 2: Remove the plastic door trim.

Remove the two screws holding the lift gate "easy reach strap". Carefully pry the plastic skin and pop the clips out. I started at the latch and worked out. Once all of the clips are loose sit the rear of the truck and pull the door toward you. The plastic slides over a bulge where the rear windows handle and door meet. Lift up and pull out here on the plastic and the whole thing should come off.

Step 3: Remove the weather barrier.

Carefully peel back the weather barrier making sure not to rip it. You'll only need to pull it back about 1/2 way to access the motor. I went right to left.

Step 4: Unplug the motor.

There is a single clip plug. Just unplug it.

Step 5: Remove the motor in its mount.

Remove 3 bolts holding the motor mount to the door. They are brass colored and mount to rubber flanges.

Step 6: Remove the motor from the mount.

There are 2 bolts holding the motor to the mount. Remove them and you now have the bad motor completely out. Take it to the parts store so you can save yourself a trip getting the core charge back.

Step 7: Re-assemble.

Just work backwards from step 6. The weather barrier should go back on without any problem, but if it lost its stick you could use rubber cement to reattach it. When you reinstall the plastic skin start with the part that has to go over the "handle bulge". Then just line it up and tap it back into the clips.


Apr 04, 2012 | 1998 Ford Expedition

1 Answer

I am trying to replace aleft rear turn signal bulb on a 2005 lacrosse. I removed two wing nuts but cannot remove assmbly. Is there another wing nut holding it in. I cannot find it?


3 wing nuts. here is the info needed.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2005 Buick LaCrosse ' Allure, LaCrosse VIN W Service Manual ' Body ' Lighting Systems ' Repair Instructions ' Document ID: 1537542 Tail Lamp, Turn Signal Lamp, High Mount Stop Lamp, License Lamp, Backup Lamp Replacement - Rear
1537540.gif
tif.gif
Callout
Component Name
Notice: Refer to Fastener Notice in the Preface section.
Fastener Tightening Specifications: Refer to Fastener Tightening Specifications .
Turn Signal/Stop Lamp Assembly Replacement - Rear 1
Nut, Turn Signal/Tail Lamp (Qty: 3)
Tip
Pull back rear compartment carpet to gain access to lamp.
Tighten
2 N·m (18 lb in)
2
Lamp, Turn Signal/Tail Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.
License Lamp Replacement 3
Screws, License Lamp (Qty: 2)
Tighten
2 N·m (18 lb in)
4
Lamp, License Lamp
Tip
Twist the bulb socket and pull inward to replace the bulb.

Jul 29, 2011 | Buick LaCrosse Cars & Trucks

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

How do i replace a 2006 A6 rear light. I crashed into a wall in the ice and it broke the plastic. I have a full replacement unit.


Rear iignts in rear na, removing and instaiiing

Fig. 325: Rear Lights In Rear Lid, Removing And Installing

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Removing

CAUTiON: • Switch off all electrical components.

. . Switch ignition off and remove ignition key.

o Turn light switch into "0" position.

o Open cap - 1 - for warning triangle.

o Rotate quick-release screw - 2 - counter-clockwise 90 C and remove cover - 3 - from luggage compartment lining - direction of arrow -

Fig. 326: Removing Bulb Socket From Housing, Pressing Catch Bracket Downward

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Disconnect electrical harness connector

o Remove bulb socket - 1 - from housing, press catch bracket - 2 - downward - arrow - to do so

Fig. 327: Identifying Nuts, Clamping Bracket, Inner Tail Lamp, And Clamp Mounting

Courtesy of VOLKSWAGEN UNITED STATES, INC.

o Unscrew nut - 2 - and remove clamping bracket - 1 -

o Remove nut - 4 - and remove inner tail lamp - 3 - toward outside

o Remove clamp mounting - 5 - from body cut-out

Fig. 328: Identifying Clamp Mounting, Nuts, Inner Tail Lamp, And Tabs

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Installing

Installation is the reverse of removal, noting the following:

NOTE: • Make sure seal between body and tail lamp housing seals properly.

. Attach clamp mounting -2 - at inner tail lamp and screw on nut -3 - loosely.

. Attach inner tail lamp -4 - at body cut-out and make sure grip tabs - arrows - of clamp mounting rest against body cut-out

. Slide clamp mounting - 1 - onto threaded pin of inner tail lamp and tighten nuts - 3 - and -5 -.

Jan 19, 2011 | 2006 Audi A6

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

1 Answer

What steps to take when taking alternator off 2002 ram 1500


From the Service Manual. You can obtain one relatively inexpensive from Promanuals.net. Here is a direct link for your truck.

(1) Disconnect negative battery cable at battery.

(2) Remove generator drive belt. Refer to 7, Cooling
System for procedure.

(3) Unsnap plastic insulator cap from B+ output
terminal.

(4) Remove B+ terminal mounting nut at rear of
generator. Disconnect terminal from generator.

(5) Disconnect field wire connector at rear of generator
by pushing on connector tab.

(6) Remove generator support bracket nuts and
bolt (Fig. 4) and remove support bracket.

(7) Remove 2 generator mounting bolts (Fig. 5).

(8) Remove generator from vehicle.

0d2b624.jpg

Oct 05, 2009 | 2004 Dodge Ram 1500

2 Answers

How to change alternator on 2005 Jeep Wrangler Unlimited?


Straight out of the repair manual:

REMOVAL
WARNING: DISCONNECT NEGATIVE CABLE FROM BATTERY BEFORE REMOVING BATTERY OUTPUT WIRE (B+ WIRE) FROM GENERATOR. FAILURE TO DO SO CAN RESULT IN INJURY OR DAMAGE TO
ELECTRICAL SYSTEM.
(1) Disconnect negative battery cable at battery.
(2) Remove generator drive belt. Refer to 7, Cooling System for procedure.
(3) Remove generator pivot and mounting bolts/nut (Fig. 2) , or (Fig. 3). Position generator for access to wire connectors.
(4) If equipped, unsnap plastic cover from B+ terminal.
(5) Remove B+ cable output terminal mounting
nut at rear of generator (Fig. 4), (Fig. 5), or (Fig. 6). Disconnect terminal from generator.
(6) Disconnect field wire connector at rear of generator by pushing on connector tab.
(7) Remove generator from vehicle.
INSTALLATION
(1) Position generator to engine and snap field
wire connector into rear of generator.
(2) Install B+ terminal to generator mounting
stud. Tighten mounting nut. Refer to Torque Specifications.
(3) If equipped, snap plastic cover to B+ terminal.
(4) Install generator mounting fasteners and
tighten. Refer to Torque Specifications.
CAUTION: Never force a belt over a pulley rim using a screwdriver. The synthetic fiber of the belt can be damaged.

Jul 05, 2009 | 2005 Jeep Wrangler

1 Answer

How do i replace the front and rear strut/shocks on 97 dodge avenger?


Always a good idea to start by disconnecting battery. For front, raise it up, remove the wheel & sway bar connector from the dampner fork. You have to remove both the upper pinch bolt and the lower damper through bolt. You have to go under the hood to remove the (3) upper strut bolts, just dont remove the big spring center nut. With both the top and bottom removed, you should be able to slide the strut out. Then you can r & r the coil spring assy, just keep everything in the same position as it was removed.
The rears, you have to jack up and block the car because you are going to also have to take the weight off of the axle by jacking it up. Of course remove the wheel- You have to go inside the car because the top mouning nuts are under the ft rear package shelf covers.will have to remove speakers & top package shelf & the covers over the nuts (2 of them). (you do have the car blocked & the axle slightly raised at this point dont you? cause you dont want to remove these nuts until you do . Now you can remove the lower strut mounts and slide it out. Again, you will have to r/r the coil spring assy with a spring compresser & be sure to put things back in the same orientation. hope this helps, rick

Apr 18, 2009 | 1997 Dodge Avenger

1 Answer

97 Taras sedan SE style rear stut top bolt and nut location.


The top nuts are located from inside of the trunk. If you look behind the material that covers the wheel wells you should find the nuts near the top of the wheel wells.

Nov 30, 2008 | 1997 Ford Taurus

3 Answers

Motor mount


The engine mounts are located about the middle of the block on the side of the engine. The only other mount is located under transmission.

Jun 09, 2008 | 1998 Jeep Wrangler

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...