Question about Toyota Avalon

1 Answer

Need to remove the passanger window switch. How does the door panel raise out to get to the switch?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I am going to go to any local parts store for a schematic diagram to see how the panel comes off. I can even go to a Toyota dealer and talk with a technician for instructions.
thank you.

Posted on Jul 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Passanger window wont roll up from driver side or passanger side


Replace the regulator. It comes with the motor. You have to remove the door panel to access it.

May 26, 2015 | 2006 Kia Sorento

1 Answer

Renault megan windows wont work on both passanger doors


This is a common problem. this is normally down to loose chock block behind the door panel. if you are lucky you can access this by removing the door speaker and reaching up behind the door panel. a good cable tie around the chock block usually solves this. (if you are unlucky you may need to remove the door panel). Good luck.

Jun 13, 2014 | 2007 Renault Megane 1.4

1 Answer

My 2008 chevy impala power window on the driver side will not raise. When you depress the switch, it tries to work. But when you try to raise the window, the switch seems to have no power. What can


z

General instructions for door panel removal; Door panels are attached to the door frame with clips such as the one above. The ribbed, screw-like part of the clips are inserted into holes in the door frame around the perimeter of the sides and bottom of the panel
Auto Repair Mechanics How to Remove Car Door Panel

The video shows details of door panel removal. First locate all the screws on the door panel, usually at the door handle and door rest. Look for any hidden screws that may be covered with small plastic caps.

After all screws are removed, the side and bottom clips need to be popped out of the door frame. You can purchase a set of trim tools to pop the clips, or you can use flat blade screw drivers and a flat putty knife to pop the clips out. Sometimes the clips break, but they are replaceable. Once the sides and bottom are loose, the top of the panel is loosened by lifting up on the panel, disengaging the panel from the top track on the door frame. Be careful of wiring connectors, which will have to be disconnected to completely remove the panel.

May 26, 2014 | 2008 Chevrolet Impala

1 Answer

2004 chevy venture: driver's electric window hesitates when trying to lower or raise it. Do I need to replace a switch, motor, etc.?


if you have fully charged battery and you are having this problem well i would take the door panel off and watch it operate make sure every thing is moving smoothly and lubed if you can switch the switches from passenger to drivers test both see if the drivers window operates normal same with other side if no change then yes find new motor on craigs list .com hope this helps you out

Jul 24, 2011 | 2004 Chevrolet Venture Passanger

1 Answer

Window motor went out and window won't go up how do i get the motor off so i can get the window up manually


LOOSEN AND REMOVE SCREWS TO WINDOW SWITCH THEN RAISE WINDOW SWITCH STILL CONNECTED.WHILE WORKING WINDOW SWITCH BUTTON SHAKING WIRE SEE IF WINDOW TRY TO GO UP. IF YES.SWITCH IS BAD.YOU CAN BUY ONE AT SALVAGE YARD FOR $60.00 NEW SWITCH COST $100.00. IF WINDOW MOTOR IS BAD YOU NEED A HAYNES REPAIR MANUAL TO FIND DOOR PANEL SCREWS TO INSIDE DOOR HANDLE.YOU NEED TO SEE SCREWS LOCATION FOR THE WINDOW MOTOR REGULATOR.YOU NEED TO SEE WHERE DOOR PANEL CLIPS WHERE YOU DISENGAGE BY USING A FLAT DOOR PANEL REMOVAL TOOL.

Feb 18, 2011 | 1995 Pontiac Grand Am

1 Answer

Driver's side power window was inop. Window failed to go back up. Chevy dealer replaced the regulator motor and now working. Now the power dood lock switch on drivers side won't unlock doors.. Is the...


Hi, that wire is disconnected when the door panel is removed to work on the window motor. Take the car back and ask them to reconnect your door locks. If you want to fix it yourself, you may be able to access the connector by removing only the control panel where the door lock switch is installed. Remove any visible screws and then pry gently to pull up the panel. Odds are, however, that the whole door panel will need to be pulled loose to find the cable. You can possibly just pull the bottom of the panel loose, but do it carefully. Feed the wire back up to the control panel and reconnect to the switch. Thanks for using Fixya.

Jan 24, 2011 | 2003 Chevrolet Venture Passanger

1 Answer

Need to remove the door panel and replace motor


This is the best I got hope it helps!

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the door speaker.
  3. Temporarily reconnect the power window switch to the door harness.
  4. Operate the power window switch to raise/lower the door glass until the door glass bolts can be seen.
  5. Remove the door glass bolts.
  6. Raise the door glass up into the door frame/channel and hold in place with a suitable tool.
  7. Remove the module assembly bolts and the module assembly.
  8. Disconnect the harness connector for the module assembly, and disconnect the harness clip from the back.
  9. To install, reverse removal procedure.
Rear
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the rear door finisher.
  3. Remove the plastic vapor barrier, being careful not to tear/damage it.
  4. Temporarily reconnect the power window switch to the door harness.
  5. Operate the power window switch to raise/lower the door glass until the bolts can be seen.
  6. Remove the door glass bolts.
  7. Raise the door glass up into the door frame/channel and hold in place with a suitable tool.
  8. Remove the bolts and the regulator and guide channel from the panel.
  9. Disconnect the connector and remove the regulator assembly.
  10. To install, reverse removal procedure.

Jan 12, 2011 | 2004 Nissan Altima

1 Answer

Doors not locking


had a similar problem. remote would not work doors and inside switch would not work on passsanger side. There is a part below the passanger side door window and lock switch called the PDM or passanger door module.capable of some really strange behavior as it basically is a mini computer and rf signal receiver. May try reprograming your remotes first, if that doesn't work get new PDM. need to give VIN to parts folk to get it. Think it was about 200.00. Need to remove passanger side door panel and then take apart armrest with door swithes. Kind of tricky. funky screw on the front which has to be loosened and door panel must be off to get to it. anyway after install reprogram the remotes to the PDM. It involves off on, off,on ignition while holding down the unlock door switch, then hold the unlock on the remote?????? the sequence in on the net just search it out for your year.

Jun 09, 2009 | 2003 Cadillac Escalade Esv

1 Answer

How do i remove the rear passanger 2000buick lasabre door panel.


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

May 08, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...