Question about 2004 Chevrolet Venture Passanger

1 Answer

Seems there may be a loose wire or something. ABS & Traction Control lights go on for days then go out and everything is fine for a few days before this happens again, over and over. In this time the Airbag light will go on too. Its like if you hit a good bump a wire or two loosens and these lights go on and the features dont work.

Posted by on

1 Answer

Hold your computer against your venture VAN while reading this, I can fix it that way... c'mon, take it to the dealership and quit trying to get something done for free. You need a wheel speed sensor or harness.

Posted on Oct 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Handbrake & traction lights on when applied brakes


All your doing is applying the brake pedal

That is the only computer input,so maybe the
switch is loose or bad- next to the brake pedal

I would scan for computer data & codes- especially
the body & abs braking system

Mar 08, 2013 | Cars & Trucks

2 Answers

ABS/ Traction control light/BAS & brake light on in 2008 dodge grand caravan


It is safe to drive. You need a scan tool to get a code out of it. Could be as simple as a wheel speed sensor going bad. All of these lights will work together normally. The traction control uses the ABS to gain traction, and the Brake Assist System is part of the stability control. Also uses the ABS.

Oct 03, 2012 | 2008 Dodge Grand Caravan

1 Answer

Abs and traction control light remain on.brakes were checked and are fine.any suggestions.


Most likely one of the wheel ABS sensors is defective, it makes the vehicle think that one wheel is turning at a different speed to the others which causes issues for both the ABS and the traction control.

Mar 10, 2012 | 2005 Chevrolet Impala

1 Answer

Brake peddle is chattering 2003 ion and would like to pull the anti lock brake fuse (if safe ) until i can afford the repair. I would like to know witch fuse to pull?ABS is on and traction control


If brake pedal is chattering or pulsating it is most likely because you need either front or rear rotors, or both. They are rusted or out of round. If there is something wrong with either your abs or traction control,the abs or traction control light will come on & stay on. As soon as these lights come on, it automatically disables abs or traction control. If you would like to take out fuse that disables abs or traction control circuits, it will leave the lights on.You just wont have their functions. If by some strange condition your chattering goes away, then there is indeed something wrong with your abs or traction control.Fuses are labeled abs or traction either under hood or in your fuse panel in car.

Jun 13, 2010 | 2003 Saturn ION

1 Answer

When i start my 2008 endeavour,the brake light wont go off. Then when i start to drive, the traction icon comes on. Any solutions?


There are a few items to check.
1) Brake fluid level
2) Brake pads
3) Wheel sensors and wiring (these send data to ABS and traction control)

If all the braking system seems to be fine then I would guess a wheel sensor is faulty which would make the warning lights come on.

Mar 30, 2010 | 2008 Mitsubishi Endeavor

1 Answer

Electrical gremlins


it could be something as simple as moisture in one of the plugs, or something as complex as a broken wire inside the harness, or a loose ground wire. i would begin by checking the ground wires to the body and the ecu (computer)

Oct 28, 2009 | 2003 Chevrolet Corvette

1 Answer

Traction conrtol , abs brake lights lincoln ls 2000


it might be a loose abs cable behind one of the brakes?

Jul 27, 2009 | 2000 Lincoln LS

1 Answer

Brake sensor? something else?


You have a faulty wheel speed sensor. This is a magnetic pick up sensor on your wheel bearing hub and it controls your abs. If the car can not sense all 4 wheels then the abs will default back to normal brakes and your traction control will not work. Look at your wheel bearing hubs and check for these sensors. They are on the underside of the car and are black plastic with a wire comming out of it. A piece of gravel may have broken the pick up or the wires to a sensor may be broken as well. To replace it is usually a couple of screws on the hub assembly and a plug to disconnect from your wire harness.

May 27, 2009 | 2003 Mazda Mazda6

6 Answers

2005 Impala abs & traction control problem


2005 Impala it turn off some times when I am coming to a complete stop or when I am slowing down but it starts right back up with no problem can you help me

Nov 10, 2008 | 2005 Chevrolet Impala

1 Answer

Abs light and traction control light cant figure out why?


clean ringer at wheel end..be sure you did not disturb alignment of sensor (VSS) which tells 'puter wheel speed for ABS and traction control

Oct 29, 2008 | 2002 Audi A6

Not finding what you are looking for?
2004 Chevrolet Venture Passanger Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...