Question about 1987 Nissan Pickup

2 Answers

1988 Nissan Pickup Clutch problem?

To put it simply enough i was in a drive through and when i reached for my wallet in my back poclet i kept my foot on the clutch all the way so when i pulled away i went to go into second gear and i couldnt go from nuetral to second or even back into first so i shut the truck down and tried to start it but it wouldnt start and my clutch pedal wasnt resisting at all its liek the clutch isnt even grabbing

Posted by on

  • circulatrue Nov 05, 2008

    No pressure on the cluth pedal at all. Tried bleeding air out of the lines after replacing the master and slave cylinders. Wtf? Any help would be greatly appreciated. I have two children that I have to get around that I can't right now.



2 Answers

Post up on

Posted on Jul 28, 2008

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

The fork in the tranmission could have got stuck and there is also two bleeds on that system you have to bleed the one on the tranmision first then the one on the master cylinder. It could posible a clutch problem but not really sounding that way.

Posted on Dec 04, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 1988 Nissan pickup, when I let out on the clutch to take off, it quits every time.

Dose the motor stall or dose the drive line lock up,more info needed.

Jul 19, 2014 | Cars & Trucks

1 Answer

Can anybody help me out with my car?

Check your throttle position sensor.

Jan 30, 2013 | Cars & Trucks

2 Answers

How do i bleed the clutch on a 2009 nissan versa

Well, you size the wrench needed for the bleed valve on the slave cylinder, mounted on the transmission housing 8 or 10 mm in most cases. Make sure the clutch reservoir is full, and kept full. Then you'll need a trusted assistant to work the pedal-one who will understand the reasoning and procedure behind bleeding a hydraulic system of air trapped inside the lines-it hinders hydraulic pressure on the clutch fork to make the clutch work at all. I say trusted because you dont wanna make it an unpleasant experience (I've participated in quite enough of those videos!) Patiently explain that the clutch pedal should be depressed slowly and steadily to the floor after you have opened the bleed valve and kept depressed to the floor until you have closed the valve. So just as the pedal starts traveling down, open the bleed valve, fluid is forced down through the line and out the open valve. Best if you close it just before the pedal reaches the floor-as soon as pressure is let off, air has a chance to re-enter through the open valve, so close it quick. A couple of times should do it-when you have a steady stream of fluid, no more air, and you know the line is bled of any possibility of air, then finish tighten the bleed valve, not too tight. Check the reservoir again, and take your trusted associate to dinner.

Sep 29, 2012 | 2012 Nissan Versa 1.6 S Sedan 1.6L 4-cyl....

2 Answers

I have a 1990 nissan pickup with a problem with the clutch pedal. there is no clutch press at the clutch pedal when i press on the pedal it just falls to the floorboard and does not return. i can lift it...

First, try bleeding it. Put a 2 foot peice of vacuum hose on the slave cylinder bleeder screw. Loosen the bleeder screw. Put the other end of the hose into a clear bottle or brake/clutch fluid. ( have the bottle about half full). Now, have someone pump the clutch by hand while you watch for bubbles in the bottle. When it stops bubbling, you have all the air out, and you can tighten the bleeder, and remove the hose, and refill the reservoir.
If it won't bubble, and no fluid comes out, your master cylinder needs replacing.
( P.S. - The slave cylinder is down under the truck. It's what pushes the clutch rod.)

Mar 13, 2011 | 1989 Nissan Hardbody King

1 Answer

I have this problem with my K Reg Audi 80 1.9 tdi...Driving along say 50mph in traffic, take foot from throttle due to traffic flow, put foot back on throttle and nothing happens unless you either let...

you car is fitted with a "no fuel"system,so when you take your foot off "no fuel" goes to the engine untill it reaches 1200 revs.then it will allow fuel to flow to keep tickover/smoothness.(its computer controlled)you need to get your car onto the diagnostic computer,(skoda/seat/vw/audi)so you have the codes/items that need to be sorted.The tdi engine was one of the first engines that VW computerised and it is very reliable/powerful,compared to the peugeot/citroen engine.(briefly,the fault is not just a switch/cable),

Nov 27, 2010 | 1988 Audi 80

1 Answer

'87 nissian pu clutch will not engage

flush all the fluid from the reservoir. your fluid is contaminated

Dec 21, 2008 | 1987 Nissan Pickup

1 Answer

4wheel drive won't engage

it has to be a linkage problem. the linkages had to be re moved to get the clutch out and have not been put back on correctly or at all.the clutch has no bearing at all on the engaugeing of 4wd

Nov 23, 2008 | 1988 Toyota Pickup

3 Answers

88 Nissan z24i backfires through throttle body and loses power when in gear

Check your intake and exhaust modules. I have a 1987 D21 and had the same problem (if I understand your post). I replaced the modules located behind the driver side headlights and it fixed the problem. Good luck! I hope this helps.

Nov 04, 2008 | 1987 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

78919 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides