Question about 1992 Lexus Sc 300

1 Answer

SC300 POWER STEERING PUMP

Where can i find a pump for a decent price besides the dealer?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

AUTOZONE OR JUNK YARD

Posted on Jul 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is there power steering pump located on 2006 dodge charger


if you have a hemi engine, the pump should be at the top of the engine towards the front, right beside the radiator. find the power steering reserviour cap, the pump should be right below it

Aug 25, 2014 | Cars & Trucks

2 Answers

What does the power steering belt on a 1994 murcery villager controls besides the power steering


Mercury right
There is only one belt so it runs all pulley driven accessories

Nov 03, 2012 | Cars & Trucks

1 Answer

Power steering pump whine and no power steering assist upon cold start up 1999 Lexus SC


Did you check the fuelid level today? A loud whine indicates low fluid or a defective pump in most cases.

Sep 10, 2012 | Cars & Trucks

1 Answer

Power steering tank wont hold fluid and leaks out beside driver tire


Sounds like a blown power steering line. To confirm, wipe down all surfaces around the power steering unit including the lines. Replace the power steering fluid and start the engine. While 1 person is inside the truck, have them turn the wheel from side to side while another watches the area around the power steering unit paying very close attention around the lines. The high pressure line is the most common cause for leaking fluid. If there's no crack or kink in the line, the issue may be the fitting itself where it connects to the power steering pump. Both parts are pricey but replacing the high pressure line (about $150 at the dealer) is certainly less expensive than replacing the whole power steering unit itself.

Jul 30, 2011 | 2004 Hyundai Santa Fe

1 Answer

Power stering pump fluid leaking.


FIRST MECHANICS COULD HAVE TIGHTEN LINE TOO TIGHT AND DAMAGED THE SEAL IN LINE FITTING.TAKE CAR BACK TO FIRST DEALER.LET THEM KNOW POWER STEERING IS STILL LEAKING AND THEY DID NOT FIX THE PROBLEM.THEY SHOULD NOT CHARGE YOU ANYTHING JOB SHOULD BE DONE RIGHT THE FIRST TIME.

Apr 29, 2010 | 2003 Mazda Tribute

2 Answers

Is replacing the power steering pump exspensive


Hello there:
no it is more cost efficient if you do it your self the cost of the pump for this car i have listed below to show you the price it would be more expensive if a shop had to do this
spaclear.gif spaclear.gif spaclear.gif tn_20497-top.jpg
spaclear.gif
Part No.
20497 spaclear.gif Cardone Power Steering Pump Power Steering Pump: Remanufactured; Without Reservoir Warranty: Limited Lifetime*




  • Ships in 1 day
spaclear.gif $42.99 spaclear.gif
$15.00 core spaclear.gif
spaclear.gif


spaclear.gif
spaclear.gif spaclear.gif spaclear.gif

spaclear.gif spaclear.gif spaclear.gif

spaclear.gif


spaclear.gif



spaclear.gif


Dec 11, 2009 | 1996 Ford Taurus

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

1992 lexus sc300 repair: Power Steering pump


replace the power steering pump. make sure you get crush rings for the hoses too. dont use stop leak stuff either because it WILL clog the filter in the power steering rack and then youll have to replace that too.

Aug 15, 2009 | 1992 Lexus Sc 300

2 Answers

My 97 lexus sc300 started making whining sounds a few weeks ago .


check to make sure there power streering fuild in da pump,and check hoses for leaks.

Nov 12, 2008 | 2005 Lexus LS400

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...