Question about 1997 Ford Explorer AWD

1 Answer

Changing marker bulb

How do i change left marker bulb on my 1997 ford explorer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 30 Answers

It is the front or rear bulb?

Posted on Aug 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the front marker assy to change the bulbs


Don't know what vehicle you have but if there arre no bolts/screws visible from the outside of your marker lense, then you should see clips on the inner fender wheel (may be covered in mud/dirt) that hold the lense in. You will probably not need to remove the assembly though, since most bulb sockets can be removed from the inner side (turn left - counter clockwise) to get to the bulb.

Nov 29, 2010 | Ford F-250 Cars & Trucks

1 Answer

Marker light problem


change them back or check to see if you have the right bulbs

Mar 05, 2010 | Ford Mustang Cars & Trucks

1 Answer

How to change side marker bulb in 1997 altima


a53bade.gif

The marker lights are removed by depressing the tab (arrow) with a thin bladed tool. Take care not to scratch the paint

  1. Disengage the bulb and socket assembly from the lens housing.
  2. Gently grasp the light bulb and pull it straight out of the socket.
To install:
  1. Before installing the light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.
  2. Line up the base of the light bulb with the socket, then insert the light bulb into the socket until it is fully seated.
  3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct as necessary.
  4. Install the socket and bulb assembly into the lens housing.

Dec 07, 2009 | 1997 Nissan.5 Altima

1 Answer

Both headlights went out at the same time on a 1997 ford explorer


first of all, answer this: Did you do some instalaltion before this happens? and then, check fuses and other connections of the headlights. If possible, take the bulbs out and test them with a direct line from the battery. If after the test the bulbs are on, then you have to check the cables and fuses. If the bulbs do not turn on in the test, then you have to buy extra bulbs to change the bad ones. EXTRA NOTE: It is really weird that both bulbs are burned... check other installations and cabling system.

Oct 27, 2009 | 1997 Ford Explorer AWD

1 Answer

How do you change the turning signal on ford contour sport?


This is for the 95-97 Contour. 98+ are different, because the light housing changed completely.
1. Open the hood.
2. In each front corner of the hood, there is a torx bolt, head about the size of a nickel. Removing this one bolt allows you to remove the corner marker/turn signal housing.
3. Once the housing is free, you have access to the back of the bulb holder. If I recall correctly, it's a half-twist to remove, but I'm not sure. Could just be barbed clips, or something. Anyway, from here should be no problem to figure out how to remove and replace the bulb.
4. Replace corner marker/turn signal housing, and re-install torx bolt. That's it!

Oct 11, 2009 | 1997 Ford Contour

1 Answer

Left hand park light not working


hi first of all check ur fuses with a good test light see if any are blown and if u had cut any wires when u took out the old stereo that would have caused the problem..

thank u
rate me!!

May 24, 2009 | 1997 Ford Explorer AWD

1 Answer

92 ford explorer back-up lights will not work. Just changed manual transmission.may have left something unplugged.Tested the bulbs and they are fine.Possible fuse or relay but I do not have the owners...


itch Operation:Photo of back up light switch, located on trans. sorry, not sure exactly where on tranny, but it probably isn't plugged in as u suspect. Photo on autozone website. 00610_backup_light_switch.jpg

Apr 15, 2009 | 1997 Ford Explorer AWD

1 Answer

Driver side headlight went out in 1996 ford explorer changed bulb still no light but i do have high beam I have the same problem with my 1997. I've had some people look at it and nobody can figure out the...


the problem is in the bulb when you replace the bulb and you touch it with your hand be sure to wipe the bulb off before installing it in the headlight assembly because it the sweat on your hand that can blow the low beam also make sure the socket is clean and just a little grease is in it

Feb 01, 2009 | 1997 Ford Explorer AWD

1 Answer

Light to one of my guages


generally,you can reach up behind the dash to twist out the bulb /holder,, or the dash cluster w/all gauges can be removed from the front to change bulbs... kev-mn.

Dec 10, 2008 | 2001 Ford Explorer Sport Trac

1 Answer

Left tail light @ blinker out


check the bulb contacts for corrosion, also check inside the bulb holder

Oct 29, 2008 | 2003 Ford Explorer Sport Trac

Not finding what you are looking for?
1997 Ford Explorer AWD Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...