Question about 1999 Ford Taurus

1 Answer

My transmission wont go into gear none of them work 1,2,3,4,overdrive, or reverse

Posted by on

  • 1 more comment 
  • rebokk9114 Jul 23, 2008

    i have the same problem with a 1997 Crown Vic. However, I can get the car in gear by shutting the engine off, then turning the ignition switch to ON, then shifting into Neutral. Once in Neutral, I can turn the ignition to START and the gearshift works normally. Any explanation on why it won't shift into gear from Park? Any solution(s)?

  • jfbmama Aug 10, 2008

    2001 crown vic transmission only shifts gears when it is cranked in neutral.  If you start the car in park none of the gears will work.  It started out with 3rd gear not working at all.  Then the OD light started coming on about once a month.  You could kill the car and restart it and the light would go away.  Now none of the gears work unless you put it in neutral to crank it.  Anyone have any suggestions?


  • Anonymous Aug 12, 2008

    wont go into gear

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is the brake switch at the top of the brake pedal
the wires are lose or its faulty check your brake lights-they dont come on when you push brake anymore
play with the switch before getting a new one
it will save you money...either way its a cheap fix

Posted on Jan 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 chevy cobalt wont run in drive it dies but will run good in reverse


On some old Buicks and Oldsmobiles the overdrive would stick on. A bandaid cure for them was to unplug the cable under the hood, but you no longer had overdrive. I heard that changing the transmission fluid would clear that up. There's no overdrive in Reverse.. placing the car in 1st or 2nd gear could bypass o/d also if they don't use the same gear set. Once up-to-speed, place the car in Drive. This only works if the reason the car dies is it can't accelerate in that high a gear at such a slow speed.

Oct 12, 2015 | 2006 Chevrolet Chevrolet Cobalt LS

1 Answer

I have a 700R4 in a 1990 Chevy 4x4 the transmission was working in another truck I put it in mine and now it changes gear 1-2-3 but it won't change into overdrive don't have nutural it's drive and reverse...


Overdrive is a function of the torque converter. When you put the transmission in the vehicle you should have change the seals and rings on the shaft. The transmission fluid travels through that. Also check the linkages and the connections.

Dec 12, 2014 | Cars & Trucks

1 Answer

1999 mitsubishi eclipse automatic transmission wont shift into 4th gear.


First off.. If you have a check engine light on, Find someone with an OBD2 READER or buy one yourself(very good tool to have) and that will give you the code(s) to your problem..

If not.. Check ALL your fuses..

If those are good and you DO NOT have a sealed tranny.. Check your fluid..

If all the above check out good.. It's gonna be 1 of 2 things..

1. Your overdrive is either turned off and/or damaged.. (Over drive on: uses all 4 gears/Over drive off: uses only 3 gears)

2. Your shift silonoid pack is damaged, which normally when this happens your car goes into a thing called "dummy mode" and keeps the tranny ONLY in 2nd gear..

Now assuming your car shifts into every other gear just fine.. And the fact that normally reverse is the first gear to go out.. I'm gonna say it's your overdrive or a relay that runs with your overdrive..

Let me know what happens or if you have anymore questions..


-Daniel
Proud Owner of the
sickest 97 eclipse.

Sep 28, 2014 | 1999 Mitsubishi Eclipse

1 Answer

I got my 2001 dodge ram 1500 with the 5.9L v8 stuck in the sand at the beach. While my buddy was pulling me out from behind, I was flooring it in reverse to get out. Then my my rpm went down and the...


Need more info: is manual shift if so 4sp ,5sp or 6sp speed?
or auto w/overdrive ?
2) wont go into gear or selects reverse gear but acts
like no gear?
3) does forward gears work?
~
4) how's the fluids?

Jan 30, 2013 | Cars & Trucks

1 Answer

1996 honda accord wont shift into overdrive


For Automatic transmission problem,click the link below:----Overdrive light in the dash blinks? http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html
--------- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Mar 04, 2012 | 1996 Honda Accord

1 Answer

Wont shift into drive but first second and reverse gears work


Sounds like you broke one of the one way clutches it the transmission. The transmission will need rebuilt or replaced. If you want to drive the truck, Take off with the shifter in 1. When you reach about 12 move it to 2, when you reach about 27 shift to drive, when you reach about 45 shift to overdrive.

Jun 14, 2010 | 2003 Chevrolet Silverado 1500

1 Answer

I have a 2000 Expedition 4.6L Triton. I've had truck about 7 years and love it. I have had all the transmission issues this truck can have...(I thought) until now this: SYMPTOM Transmission drives well in...


4R100 or 4R70W?

Geartrain
Power is transmitted from the torque converter to the geartrain components through the input shaft and forward clutch cylinder.
  • By holding or driving certain members of the gearset, four forward ratios and one reverse ratio are obtained and transmitted to the output shaft. The ratios are as follows:


GEAR RATIO 1ST 2.71 to 1 2ND 1.54 to 1 3RD 1.00 to 1 4TH 0.71 to 1 REVERSE 2.18 to 1
Input Shaft
The input shaft is supported by two bushings in the stator support. End positioning of the input shaft is controlled by the splines in the converter turbine and the overdrive planet assembly.
Output Shaft
The output shaft is supported by two bushings in the case and by the slip-yoke and bushing in the extension housing. End positioning is controlled by the parking pawl gear and snap ring or shoulder and by the reverse ring gear hub and snap ring.
Overdrive System
The overdrive planetary system consists of the overdrive planet assembly, overdrive sun gear, overdrive ring gear, coast clutch cylinder, overdrive one-way clutch assembly and the center shaft, as shown in the following illustration. The overdrive planet assembly is splined to the input shaft. The overdrive sun gear is centered by a bushing on the input shaft and held in place laterally by needle bearings on the reactor support and the overdrive planet assembly. The overdrive sun gear is splined to the coast clutch cylinder, which in turn is splined to the overdrive one-way clutch inner race.
The outer race of the one-way clutch is splined to the overdrive ring gear, which is splined to the center shaft. The center shaft is centered by the forward planetary assembly and is laterally held by needle bearings on the center support and the overdrive planet assembly. The center shaft is splined into the forward clutch cylinder.
Two friction clutches are assembled in the overdrive planet assembly. The coast clutch is splined between the coast clutch cylinder and the overdrive ring gear. The coast clutch is activated to perform engine braking in MANUAL 1, MANUAL 2 and third gear with the transmission control switch engaged.
The overdrive clutch is splined between the case and the coast clutch cylinder. The overdrive clutch holds the coast clutch cylinder and, in turn, the overdrive sun gear, to permit the planet assembly to overdrive the ring gear.
--------------------------------------------------------------------------------------------
Forward Drive System
The forward drive system consists of the forward clutch cylinder, intermediate brake drum, intermediate one-way clutch, input shell, forward ring gear, forward ring gear hub, forward/reverse sun gear and the forward planetary carrier and forward planetary gears.
The forward clutch cylinder is splined on the center shaft. The forward ring gear is piloted on the forward ring gear hub. Thrust bearings on the forward planet assembly and forward clutch cylinder hold the forward ring gear hub in place.
The intermediate brake drum is radially supported by bushings on the center support and is laterally controlled by thrust washers on the forward clutch cylinder and center support. The intermediate brake drum has the inner race of the intermediate one-way clutch press-fitted on its pilot. The intermediate one-way clutch's outer race is splined to the intermediate friction clutch, which is splined to the case. The intermediate brake drum has lugs that are slotted into the input shell to form a mechanical connection. The input shell is splined into the forward/reverse sun gear. The forward/reverse sun gear is common to two planetary gearsets. The forward planet is splined to the output shaft and is laterally positioned by needle bearings on the sun gear and on the forward clutch cylinder, as shown in the following illustration.
Two friction clutch assemblies, the direct clutch and the forward clutch, are shown with the forward planetary assembly. The direct clutch assembly splines the forward clutch cylinder to the intermediate brake drum. The forward clutch assembly splines the forward clutch cylinder to the forward ring gear. The forward clutch is activated during all forward gears. While in third or fourth gear, both the direct and forward clutches are applied to hold the forward planetary assembly and enable it to act as a solid shaft.
In second gear, the intermediate clutch assembly holds the forward/reverse sun gears. It is applied, along with the intermediate one-way clutch, to hold the intermediate brake drum, input shell and forward/reverse sun gear. In higher gears, the one-way clutch overruns.
----------------------------------
Low and Reverse Drive System
The reverse planetary assembly consists of the reverse planetary carrier, reverse planet gears, the reverse ring gear, the reverse ring gear hub, the reverse clutch hub and the low-reverse one-way clutch assembly.
The reverse ring gear hub is splined to the output shaft and to the reverse ring gear. The reverse ring gear hub is laterally held by a needle bearing on the inner race of the low-reverse one-way clutch and a snap ring on the output shaft. The reverse planet assembly is splined to the low-reverse clutch hub. The low-reverse clutch hub is connected by the reverse clutch to the case. The inner race of the one-way clutch is bolted to the case.
The reverse clutch assembly is activated in REVERSE gear and in MANUAL 1. The reverse clutch bypasses the reverse one-way clutch during coast and MANUAL 1. The reverse clutch holds the reverse planet assembly in REVERSE gear to enable the sun gear to drive the reverse ring gear in the opposite direction.
-------------
Apply Components
The following information describes the operation of the three 4R100 one-way clutches.
One-Way Clutch—Overdrive
The overdrive one-way clutch, shown in the following illustration, transmits engine torque from the overdrive sun gear to the overdrive ring gear in first, second and third gear range. The overdrive one-way clutch transmits power when the sprags are engaged between the inner and outer races. The inner race is splined to the coast clutch cylinder, which in turn is splined to the overdrive sun gear. The outer race is splined to the overdrive ring gear.
The overdrive one-way clutch engages whenever the overdrive planetary system attempts to drive the overdrive sun gear clockwise when the overdrive ring gear has a counterclockwise torque from the vehicle. When torqued counterclockwise, the overdrive one-way clutch engages and acts as a wedge to lock the sun gear and the ring gear together. During coast, the overdrive one-way clutch enables the ring gear to overrun or spin at a faster rate than the sun gear.
The overdrive one-way clutch overruns when in overdrive (fourth gear). In overdrive, the coast clutch cylinder is held by the overdrive one-way clutch, which in turn holds the overdrive sun gear. This causes the overdrive planet assembly to walk around the sun gear and overdrive the overdrive ring gear. The inner race of the overdrive one-way clutch is thus held stationary while the outer race is allowed to overrun clockwise.
--------------------------------------------

Nov 10, 2009 | 2000 Ford Expedition

1 Answer

Tranny wont shift


Sounds like you need a rebuild on your transmission. The overdrive is going out in the transmission system.

Mar 05, 2009 | 1993 Chevrolet S-10

Not finding what you are looking for?
1999 Ford Taurus Logo

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...