Question about 1999 Honda Odyssey

1 Answer

Not a 99 but an 04 wiring diagram for map sensor

I am trying to figure out which wire goes to the computer.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

All wires on the sensor go to the computer, one will be a standard power wire going to the sensor, and the other 2/3 will be resisted signals going from the sensor to the computer

Posted on Aug 05, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a wiring diagram for map sensor in 2006 Jeep Liberty 4x4 3.7L


Go to autozone and ask for the wiring diagram. They will print one for you for free. If you dont have an autozone near you try another parts store. If you purchase a haines of chiltons manual ($25 in a retail store or $18 on amazon), it will have a detailed wiring diagram of the MAP sensor.

Good Luck!

Jul 13, 2014 | 2002 Jeep Liberty

1 Answer

Code po 107 comes up on my 98 chevy pu map/baro circuit low input already change the map sensor and find that there is no power in the plugwhat do I change now?


You may need a wiring diagram to make sure, but I think the gray wire is reference voltage and it also powers the throttle position sensor. The sensors get power from the engine computer.

Sep 23, 2013 | 1998 Chevrolet Cavalier

5 Answers

MAF, IAT, MAP and Coolant Level Sensor Problem


They share the engine wiring harness from the computer (called the PCM) and a common ground circuit, which is referred to as the signal return. So I think you need to look for a defective ground.

Nov 18, 2011 | 2003 Mazda MPV

1 Answer

When i punch on the gass my 97 tahoe hesitates


usually a bad MAP sensor or TPS. I would test both. Let me know if you have questions and provide test results for repair advice.

MAP Sensor TESTING
See Figures 3, 4 and 5
  1. Backprobe with a high impedance voltmeter at MAP sensor terminals A and C.
  2. With the key ON and engine off, the voltmeter reading should be approximately 5.0 volts.
  3. If the voltage is not as specified, either the wiring to the MAP sensor or the ECM may be faulty. Correct any wiring or ECM faults before continuing test.
  4. Backprobe with the high impotence voltmeter at MAP sensor terminals B and A.
  5. Verify that the sensor voltage is approximately 0.5 volts with the engine not running (at sea level).
  6. Record MAP sensor voltage with the key ON and engine off.
  7. Start the vehicle.
  8. Verify that the sensor voltage is greater than 1.5 volts (above the recorded reading) at idle.
  9. Verify that the sensor voltage increases to approximately 4.5. volts (above the recorded reading) at Wide Open Throttle (WOT).
  10. If the sensor voltage is as specified, the sensor is functioning properly.
  11. If the sensor voltage is not as specified, check the sensor and the sensor vacuum source for a leak or a restriction. If no leaks or restrictions are found, the sensor may be defective and should be replaced.



jturcotte_512.jpg

Fig. Fig. 3: Location of the MAP sensor-TBI system shown


jturcotte_513.jpg

Fig. Fig. 4: Probe the terminals of the MAP sensor to check for proper reference voltage


jturcotte_1792.gif

Fig. Fig. 5: Manifold Absolute Pressure (MAP) sensor wiring diagram








TPS TESTINGSee Figures 2, 3 and 4

  1. Backprobe with a high impedance voltmeter at TPS terminals A and B.
  2. With the key ON and engine off, the voltmeter reading should be approximately 5.0 volts.
  3. If the voltage is not as specified, either the wiring to the TPS or the ECM may be faulty. Correct any wiring or ECM faults before continuing test.
  4. Backprobe with a high impedance voltmeter at terminals C and B.
  5. With the key ON and engine off and the throttle closed, the TPS voltage should be approximately 0.5-1.2 volts.
  6. Verify that the TPS voltage increases or decreases smoothly as the throttle is opened or closed. Make sure to open and close the throttle very slowly in order to detect any abnormalities in the TPS voltage reading.
  7. If the sensor voltage is not as specified, replace the sensor.



jturcotte_514.jpg

Fig. Fig. 2: Using a DVOM, backprobe terminals A and B of the TPS sensor to check for proper reference voltage


jturcotte_515.jpg

Fig. Fig. 3: Using the DVOM, backprobe terminals C and B of the TPS sensor, open and close the throttle and make sure the voltage changes smoothly


jturcotte_1793.gif

Fig. Fig. 4: Throttle Position Sensor (TPS) wiring diagram

May 30, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

All the insulation on my map sensor pigtail wires has burned off. A friend of my cut the wires near the computer and I bought a new pigtail... but the wires on the new pigtail are all white and I need to...


Okay here we go, there are three wires from the map sensor, if you look at the sensor there are letters stamped on the plug area, theres an A,B,and C the wires start from the sensor as orange/blk to terminal A then lite green wire to terminal B and last is gray wire to terminal C . im not sure what wires your freind cut but there only one at computer for map sensor and thats the signal wire, all slots at computer are numbered the signal wire is light green and connects to slot #25. heres a diagram for all wires to computer you will need to locate the wire in order to connect them back, this is not hard find the open slots and check diagram for wire color, hope this helps, good luck.3b58cfd.gif

Oct 27, 2010 | 1998 Oldsmobile Achieva

1 Answer

MAP or MAF Sensor Diagram for 2005 Town&Country Touring Van 3.8l.


Yes it has a sensor and they are color coded however I don't think it's called a maf or map sensor that’s a GM name, there would be three wires on it on ground one 5 volts reference and one for connection to the computer to tell the computer how much air flow there is, and the reading would be from 1.5 volts to 4 volts.

Jun 20, 2009 | 2005 Chrysler Town & Country

1 Answer

Map Sensor


one wire gos signal,5 volt, other gos 12 volt. other to ground need a wire diagram to determine which one is

Sep 05, 2008 | 1994 Chevrolet S-10

1 Answer

Map Sensor Wires Question


Answer:

On a 3-wire MAP sensor connector when looking at the vehicle "wiring harness mating side of the connector" (and not the sensor connector) - with the snap detent pointing UP and looking LEFT to RIGHT the signals will read >

GROUND > MAP SIGNAL > POWER


Hopefully we are talking about a MAP sensor, and NOT a MAF sensor as the 2 are different as to the wiring signals.

Color of the wires doesn't matter, as you are just looking for backprobed voltage SIGNALS only using an adapter if you are doing in-circuit signal testing.

POWER I believe should be in the 5-volt range unless Jeep is using 3.3-volt.

Usually the MAP SIGNAL voltage range is quite a bit lower on the sense line, but with Jeep you never know? If using a good DVM measuring the MAP SIGNAL voltage you should see a smooth decrease in voltage as the vacuum is increased. If there is no voltage change or negative swing then the sensor may either be bad or else you have an OPEN or SHORTED wire between one of the 3 connector leads and the PCM computer, which would be rare.

I take you are troubleshooting a specific CHECK ENGINE CODE hopefully, as if not I would have the PCM read properly with a good CAN OBD II code reader to pinpoint the troublesome sensor.

I've always used an ACTRON CP9087 Sensor Tester, and a CEN-TECH 94169 CAN OBD II code reader which works great for me.

Make sure your MAP vacuum line is good and hooked up right as well.

Let me know what you find?

Thx,

Frank

Jul 10, 2008 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
1999 Honda Odyssey Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...