Question about Isuzu Trooper

2 Answers

Replacing master brake cylinder. Will brake system have to be bled. How do you blled this system?

Posted by on

  • mardebtac Jul 20, 2008

    Thanks,

    Will let you know if successful.

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 6,487 Answers
Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,427 Answers

Ok here are the steps
1.) replace the master cylinder and ensure its secure
2.) pump the break peddle until is hard and right up

3.) if is not getting right up you may need to bleed the system but opther than that you shouldnt have any problems..

Posted on Jul 20, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do you have to remove brake lines when you change the brake booster


Check rear of Master Cylinder--If wet likely Master Cylinder Leaking and Booster Damaged. They Should be replaced as a mated pair. (for warranty) and brake lines removed and system bled.

Oct 16, 2014 | 1988 Ford F 150

1 Answer

No brake pressure...


I would keep bleeding. If there is not any brake fluid leaking, there must be air in the system. with the master cyl cap off, open one bleeder valve on the front and let it bleed for 10 mins. close and repeat with the rest. there must be an air bubble in the system! good luck

Nov 07, 2013 | Ford F-250 Cars & Trucks

1 Answer

Ford Explorer Master Cylinder replacement


you need to bleed the brakes as well

Jul 10, 2013 | 1996 Ford Explorer

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

2 Answers

2000 mercury cougar.....no brake paddle we replaced master cly,booster......what can it be


did you bleed all of the air from the master cylinder before you installed it, this has to be done. also when replacing the master cylinder, all 4 wheel cylinders will have to be bled, in order to get all of the air out of them. while doing the wheel cylinder bleeding , you will have to make sure that the master cylinder doe's not run out of brake fluid, check it each time you bleed a wheel cylinder , add brake fluid to the master cylinder each time or when it is getting low. hope that this has helped you.

Apr 16, 2011 | 2000 Mercury Cougar

1 Answer

Replaced master cylinder bled complete system stil bad braking no


does the car pull one side when you brake,if it does one of the caliper is seized if not you have to bleed again or the rubber in master cylinder gonne

Nov 22, 2009 | 1998 Toyota Corolla

2 Answers

1998 Dodge caravan. air in abs.


You cant bleed the ABS,this is your anti lock brake system,try to bleed them again,then check your power brake booster,check for loose vacuum hoses.

Jun 29, 2009 | 1998 Dodge Caravan

2 Answers

2005 f150 spongy brakes


possibly new master cylinder is defective

Mar 24, 2009 | 2005 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...