Question about 2001 Mazda Protege

1 Answer

Rear brakes I can not get the piston in the caliper to go in all the way.....what do I do???? Thanks man

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

Rear Disc Brakes usually have an "ratchetting" Piston and you need to rotate the piston as you press it back in.

They make a special wrench for this and you can purchase it at any of the major autoparts retailers...

I believe that driver side turns one way and the passenger side turns the oposite.

Posted on Aug 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to retract rear caliper piston on a 2006 Audi A6


you have to be careful there is a rear brake caliper tool for this and you can get it at napa or car quest or from a matco tool guy or snap on man it will cost any where from 49.99 to 128.99

Sep 20, 2012 | 2006 Audi A6

2 Answers

If the brake caliper piston will not go back into the piston bore do it need to be replaced.


try to get it overhauled..because might be it has gone jammed due to dust clottings......else get it replaced due to severe risks of brakes jams

May 06, 2011 | Pontiac G6 Cars & Trucks

1 Answer

I have a 2001 BMW 318I, E46 MODEL , HOW DO YOU FIT BRAKE PADS TO FRONT AND REAR, THANKS TREVOR.


YOU NEED A PISTON COMPRESS TOOL TO PRESS PISTON BACK IN THE BORE WITH THE BLEEDER SCREW OPEN ON THE CALIPER*.CLOSE BLEEDER SCREW JUST BEFORE THE CALIPER PISTON IS PUSHED FULLY INTO CALIPER.THIS WILL ALLOW ROOM FOR NEW BRAKE PADS AND CALIPER FIT OVER THE BRAKE ROTOR.WHEN FINISH.PUTTING BRAKE PADS ON YOU HAVE TO BLEED BRAKE SYSTEM.DONT DRIVE VECHICLE IF YOU CANT GET A GOOD FIRM BRAKES.

Oct 15, 2010 | BMW 318 Cars & Trucks

1 Answer

2006 Kia Spectra 5 rear brake disc replacement


you need a special tool avalable at most parts stores. its a disc brake piston turning tool. you have to rotate piston clockwise while pushing in on piston. you can fabricate something that enguages the slots and push and turn till all the way in.make sure to note position of slots and put them in same place as was before or the pin on the pads wont enguage the slot

May 10, 2010 | Cars & Trucks

1 Answer

2006 Kia Spectra 5 rear brake disc replacement


One side,turns right,and push in slightly,and the other side turns left,to retract.

Apr 20, 2010 | 2007 Kia Spectra5

1 Answer

Changing rear brake pads


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Please rate my response. Thanks!

Apr 09, 2010 | 1999 Volkswagen Passat

3 Answers

Changing the front brake pads on a 2006 Pontiac Montana SV6


no that is only the older rear calipers on gm and others. the fronts do not have that style caliper and sound like the calipers are frozen and may be way your changing the pads. try opening the bleeder screw and then compressing them if they go then you need need brake hoses and if not you need calipers. god luck man

Dec 13, 2009 | 2005 Pontiac Montana SV6

2 Answers

I need to know what tool we need to use to change the rear brake brakes, they are the discs in a 2007 grand caravan 3.3l


You will need a 7mm allen wrench or socket the socket is easier with a ratchet to undo the 2 bolts that hold the caliper on.After you take the bolts out take a screw driver and pry up on the caliper to release it off the rotor. your calipers are on top of the rotors. To compress the caliper pistons in take a pair of channel locks that open up alot then with the back brake pad still on squeeze the piston and pad in. That should do it :)

Jul 17, 2009 | 2007 Dodge Caravan SXT Minivan New Cars

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

1 Answer

How do you compress rear brake caliper?


Dear Sir/madam,

The pistons on the rear brake calipers SCREW in to the caliper. There are notches on the inner edge of the piston face. engage the notches with a large needle nose plier or a large flat washer and turn clockwise (as you face the piston) to turn the piston in.
There is a special tool that is available at your local autoparts store that is absolutely necessary and will save you a ton of time and aggravation. Using a needle nose plier or washer does not allow you to apply enough pressure unless your are the incredible hulk.

thanks
Good luck

Oct 24, 2008 | 1999 Buick Park Avenue

Not finding what you are looking for?
2001 Mazda Protege Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...