Question about Mitsubishi 3000GT

1 Answer

My son has a 96 mitsubishi 3000 GT. The power locks, when unlocked with the keyless fob, repeadedly lock and unlock, for about 5 seconds. Need to use key to gain access. Could this be an actuator, or some kind of switch in the system?

Posted by on

  • Anonymous Mar 09, 2009

    same problem here but i have a 98 3000gt sl

  • Roger H Apr 15, 2009

    I am having the same problem but it happens with either the key and/or remote. It stops after the door is closed again and locked.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

It is the multipin plug/connector inside the drivers door jam (near the door hinge). Common fault with door locks shorting on other wires (drivers door speaker wire in my case). Try releasing the retaining handle GENTLY (plastic handle that holds the multipin connector together) and wiggling the connector slightly apart (just enough to stop the "machine gun central locking - which is the symptoms name").

Posted on Aug 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

2 Answers

How do you program a keyless entry fob for a 2012 monte carlo


Close all the vehicle doors. Insert the ignition key into the ignition lock cylinder. Press and hold the DOOR unlock switch. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter. Repeat the previous step to program up to four transmitters. - See more at: http://theandrewhughes.com/2007/05/how-to-program-most-gm-key-fobs/#sthash.6oXk0NFT.dpuf

Jun 07, 2015 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Doors dont lock with secrity fob


The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

Sep 05, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

Hi I want to program a new keyless fob. I have the original fob that works great.Do I need to do anything to the original key when I program the new fob? 2006 nissan altima


1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Nov 16, 2009 | 2006 Nissan Altima

1 Answer

Keyless entry wont work 2002 chevy s10 LS


try this procedure to reporgram:

1. Close all vehicle doors.

2. Insert the key into the ignition.

3. Hold down the power UNLOCK button on the driver's continue to hold down until instructed
to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.

5. Turn the key to the ON position (as far as you can go without starting the engine).

6. Turn the ignition switch to the OFF position.

7. Turn the ignition switch to the ON position.

8. Turn the ignition switch to the OFF position.

9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the vehicle locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode

Jun 30, 2009 | 2002 Chevrolet S-10

1 Answer

I need to program the key fob


. Enter 5-digit permanent entry code into the keyless entry driver door keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
unlock confirming you are in programming mode.

3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
cycle to indicate succesful programming.

4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
to indicate succesfull programming. (If the keypad light goes out before all remotes are
programmed the entire process must be repeated).

5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

Jun 29, 2009 | 1997 Mercury Grand Marquis

1 Answer

How to program a keyless entry fob for 2005 gmc envoy - i am replacing the battery in my key fob every 5 days. I have to be right next to the car for it to work. Any idea what would cause this. I ordered a...


Seating in the drivers seat , make sure all doors are closed.Insert key into ignition, don't turn on yet.
Wait for the dome light to go out, then press and hold the door unlock button , make sure it is UNLOCK, while turning the key ON OFF ON OFF Twice , do not engage the started, just on to the point of being on. Release the unlock button,and your doors should lock, then unlock indicating programming mode.At this point hold down both the lock and unlock button on the key fob. After 30 seconds your locks should lock and unlock, indicating the fob is programmed. This must be repeated for all remotes, whether or not it be new or old. After all remotes are programmed, turn the key off and on again to exit programming mode.

May 18, 2009 | 2005 GMC Envoy

2 Answers

Programming instructions for 2006 Mitsubishi raider remote


Note when entering program mode using that fob, all other programmed transmitters will be erased and you will have to reprogram them for your vehicle. Use the following procedure to program additional key fobs if the vehicle is not equipped with Sentry Key:

1. Enter your vehicle and close all doors.
2. Fasten yo belt to cancel any chiming that may confuse you
3. Place the key into the ignition turn to on pos. do not start
4. Press and hold the UNLOCK button on the key fob.
5. After holding the UNLOCK button for four seconds, also press the PANIC button within 6 seconds.
6 When a single chime is heard release both buttons. The chime is an indication that you have successfully entered program mode. All transmitters that are to be programmed must be done so within 60 seconds of when the chime was heard.
7. Using the fob to be programmed, press and hold both the LOCK and UNLOCK buttons, simultaneously for 2 seconds and them release.
8. Press and release the UNLOCK button a single chime will be heard,
9 Repeat steps 7 and 8 to program up to six additional transmitters.
10. Turn the ignition to the OFF position.
11. Your vehicle will remain in program mode up to 60 seconds from when the original chime was heard. After 60 Seconds, all programmed transmitters function normally.

Apr 21, 2009 | Mitsubishi Raider Cars & Trucks

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...