Question about Chrysler Cirrus

1 Answer

Where is the crank sensor located at so i can replace it

Posted by on

  • mikedrice Aug 21, 2008

    where is the crank sensor located on a 2000 chrysler cirrus 2.4 litre

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 112 Answers

Tools needed 5/16" Socket, ratchet, small flathead and a jack... Get the car up, look behind engine (trunk side) right under the exhaust, there is one bolt, real easy... Remove bolt, use screwdriver to press out red clip, remove plug, twist and pull on sensor until it comes free, press back in, re-install bolt, plug.. drop car and drive away... easiest and fastest way to make wife happy !! :) Good luck...

Posted on Oct 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crank shaft sensor location on 95 lexus sc300 please help


images for Where is crankshaft sensor location on 95 ...

eplaced engine on '97 SC300 now new engine does not have Crank ...

www.clublexus.com/.../633233-replaced-engine-on-97-sc300-now-new-...
May 4, 2012 - Location: arizona. Posts: 3 ... apparently 95-97s had an additional crank sensor. .... 1995 Lexus SC300 5spd Na-T ( TT Ecu Mod + a few others) 2jzge position sensor??
Nov 2, 2011
SC400 Crank Shaft Position Sensor. WHERE?????
Oct 11, 2011
SC300 No Spark
Oct 2, 2010
What happens if the Camshaft Position Sensor goes bad?
Jun 18, 2009
More results from www.clublexus.com

Lexus Crank Position Sensor ' LS400 SC300 ES300 GS300 ...

www.partsgeek.com > Crank Position Sensor > Lexus Parts & Accessories
Products 1 - 10 of 68 - 95 1995 Lexus LS400 Crank Position Sensor Denso NLA 7/13 ... 96 1996 Lexus SC300 Crank Position Sensor Denso Includes Pigtail.

Jan 27, 2016 | Lexus Cars & Trucks

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

2 Answers

Where would i get a diagram to show me where the crank sensor on my 1997 town and country van is


The crank sensor will be located on the back of that engine. By the starter. YouTube has a cool video about it.

Oct 03, 2014 | 1997 Chrysler Town & Country

1 Answer

My engine stalls?


The crank sensor is located behind the crank pulley on the 3.8 liter. The crank pulley must first be removed. A 15/16" socket, three very long 8 x 1.0 bolts (pretty sure that is the size, some large washers, and a crank pulley pulley will be required.

With the crank pulley removed mark the bracket where the old crank sensor is located so that the new sensor can be placed in exactly the same position. Failure to do this will result in the new sensor and/or the crank pulley being severely damaged.

Then it's as simple as removing the old sensors and installing the new one.

Good luck and let me know if you have any questions.

Sep 21, 2014 | 2001 Buick LeSabre

1 Answer

Where is the 2nd crank shaft sensor located, and is there a diagram to show where these sensors are located?


is it a no crank or crank no start?
Possible causes for code P0335
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery

Read more: http://engine-codes.com/p0335.html#ixzz3Cxw6SN6O

Sep 10, 2014 | 2004 Buick Rendezvous

1 Answer

How to replace crank sensor


My crankshaft position sensor is located underneath my car, towards the middle of the two front seats. That's if you are talking about the same sensor. Good luck and take care. :-)

Apr 05, 2014 | 2005 Dodge Neon

1 Answer

How do i replace crank sensor on 2000 olds alero 3.4 and where is it located


It depends on which crank sensor you are wanting to replace. There are two of them. The 24X sensor is located behind the front crankshaft pully and the crank pully must be removed to change it. The 7X sensor is located in the engine block on the right bank (firewall side) near the rear of the engine. This one simply pulls out of the block after disconnecting the electrical connector and removing the single bolt that holds it.

Dec 13, 2011 | 2001 Oldsmobile Alero

1 Answer

2000 v10 ford f350 wont start with out either


If the crank sensor circuit is malfunctioning, then that is your problem. The code does not mean that you must replace your crank sensor. (sometimes it means this, sometimes it does not) The code means that either the crank sensor CIRCUIT is out of range or the crank sensor cannot SYNCRONIZE with the cam sensor. There is a whole lot more to diagnosing a crank sensor circuit than simply replacing the crank sensor. Proper diagnostic procedures need to be followed to locate the exact cause of the problem.

Nov 18, 2011 | Cars & Trucks

1 Answer

Ive replaced the cam shaft sensor but need to see about fixing the crank shaft sensor and do not know where its located


The crank shaft sensor is located on the front of the engine under the timing cover. In order to replace it you will need to remove the timing belt.

Jan 22, 2010 | Chrysler LHS Cars & Trucks

2 Answers

2005 ford excursion cam sensor location I need to change the cam sensor and the crank sensors on my excursion and i do not know where they are located


On my 02 Excursion with the 7.3L Diesel, the Cam Position Sensor is located at the front bottom of the engine on the passengers side. There is one electrical pigtail plug that is attached and one bolt holds the sensor in position. It may be located in a similar location on your 05 Ex. I do not know where the crank sensor is located. I hope this helps.

Aug 27, 2009 | 2005 Ford Excursion

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...