Question about 1992 Honda Accord

1 Answer

Fuel pump - 1992 Honda Accord

Posted by on

  • Emilijo Aug 15, 2008

    Fuel pump not working, the car has been crashed badly but motor and
    electric instalation is ok, my question is does the car have some kind of safety switch that crash trigers to cut out the fuel delivery and if so, where is that switch???


×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 640 Answers

Whats the issue?

Posted on Jul 20, 2008


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2008 GMC sierra 5.3 L with a new fuel pump. And no power to the pump. Any ideas where to look?


Fuel Pump Flow Control Module (FPCM) - LMF
The fuel pump flow control module (FPCM) is a serviceable GMLAN module. The FPCM receives the desired fuel pressure message from the engine control module (ECM) and controls the fuel pump located within the fuel tank to achieve the desired fuel pressure. The FPCM sends a 25 KHZ PWM signal to the fuel pump, and pump speed is changed by varying the duty cycle of this signal. Maximum current supplied to the fuel pump is 15 amps. A liquid fuel pressure sensor provides fuel pressure feedback to the FPCM.
Electronic Returnless Fuel System (ERFS) - LMF
The electronic returnless fuel system is a microprocessor controlled fuel delivery system which transports fuel from the tank to the fuel rails. It functions as an electronic replacement for a traditional, mechanical fuel pressure regulator. A pressure vent valve within the fuel tank provides an added measure of fuel pump flow control module (FPCM). Desired fuel pressure is commanded by the engine control module (ECM), and transmitted to the FPCM via a GMLAN serial data message. A liquid fuel pressure sensor provides the feedback the FPCM requires for Closed Loop fuel pressure control.

Fuel Pump Flow Control Module (Gas except LU3/LMG/LY6/LC9)
Mounted to the rear frame, near the spare tire mount
Wheels/Vehicle Underbody Component Views
Component Connector End Views
Fuel Pump Relay - Secondary (Gas with LY6)
On the fuse block - underhood bracket

DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
DTC P0192: Fuel Rail Pressure (FRP) Sensor Circuit Low Voltage
DTC P0193: Fuel Rail Pressure (FRP) Sensor Circuit High Voltage
DTC P0230: Fuel Pump Relay Control Circuit
The engine control module (ECM) sends the fuel enable signal to the fuel pump control module (FPCM). The control module monitors the voltage on the fuel pump relay control circuit. If the control module detects an incorrect voltage on the fuel pump relay control circuit, a fuel pump relay control DTC sets.
The control module monitors the voltage on the fuel pump relay control circuit. If the control module detects an incorrect voltage on the fuel pump relay control circuit, a fuel pump relay control DTC sets.
DTC P0231: Fuel Pump Control Circuit Low Voltage
DTC P0232: Fuel Pump Control Circuit High Voltage
DTC P023F: Fuel Pump Control Circuit
DTC P025A: Fuel Pump Control Module Enable Circuit

Your best bet , take it to a qualified repair shop , dealer .

Mar 25, 2017 | GMC Cars & Trucks

1 Answer

How do i replace fuel pump 95 taurus 3.0 6v ohc


You must remove the fuel tank to replace the fuel pump.
  1. Remove fuel tank.
  2. Remove any dirt that has accumulated around fuel pump module retaining flange.
  3. Turn fuel pump module locking retainer ring (#1)counterclockwise using Fuel Tank Sender Wrench 310-D006 and remove fuel pump module locking retainer ring.
  4. Pull fuel pump module sender plate up out of fuel tank until locking tabs(#3) for fuel pump module are accessible. Reach through fuel pump module opening, squeeze both locking tabs together and remove fuel pump module from fuel tank.

26441642-y320zuz4l2sbnhw34kuglarm-4-0.gif

Jan 10, 2017 | Cars & Trucks

2 Answers

How do I change the fuel pump in a 2009 GMC Acadia


drop the fuel tank and remove the circle lock. Youll see it when you take the cover off.

Feb 03, 2015 | GMC Cars & Trucks

2 Answers

No fuel coming to carburator


It could be fuel pump or fuel pump relay.Click here to see how to remove fuel pump.Click here to see fuel pump.See how much the fuel pump is,make sure it's that.Here's the fuel pump relay.Here's how to remove fuel pressure.

Dec 23, 2012 | 2003 Saturn VUE

2 Answers

Where is fuel pump for 1996 mercury mystique located on the car and how do you remove it


SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B
Removal
  1. Depressurize fuel system as outlined in Service Procedures- Fuel System Pressure Relief.
  1. Remove rear seat cushion. Refer to Section 01-10.
  1. Remove plastic grommet from floor pan.
  1. Disconnect fuel pump module electrical connector.
  1. NOTE: To disconnect fuel tubes from fuel pump module, compress tabs on both sides of each nylon push connect fitting and ease fuel tube out of fuel pump module.

    Disconnect fuel and vapor return tubes from fuel pump module.
  1. Turn fuel pump locking retainer ring counterclockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent and remove fuel pump locking retainer ring.
  1. NOTE: After fuel pump module removal, immediately cover fuel pump module opening in fuel tank in order to prevent fuel system contamination.

    Remove fuel pump module and cover fuel pump module opening in fuel tank.
  1. Remove fuel pump module O-ring seal and discard.
Installation
  1. NOTE: When cleaning fuel pump module mounting surface on fuel tank, use caution to prevent any foreign material from entering fuel system.

    Clean fuel pump module mounting flange and fuel pump module mounting surface and O-ring seal groove on fuel tank.
  1. Apply a light coat of Premium Long-Life Grease XG-1-C, -K or equivalent meeting Ford specification ESA-M1C75-B on a new O-ring seal to hold it in place and install it into the O-ring seal groove on the fuel tank.
  1. Install fuel pump module carefully to ensure that filter is not damaged. Make sure that locating keys are in keyways and O-ring seal remains in place.
  1. Hold fuel pump module in place and install fuel pump locking retainer ring finger-tight. Make sure that all locking tabs are under fuel tank lock ring tabs.
  1. Secure fuel pump locking retainer ring by rotating clockwise using Fuel Tank Sender Wrench D84P-9275-A or equivalent until fuel pump locking retainer ring rests against stops.
  1. Connect fuel and vapor return tubes to fuel pump module.
  1. Connect fuel pump module electrical connector.
  1. Install plastic grommet in floor pan.
  1. Install rear seat cushion. Refer to Section 01-10.
  1. Install Multi-Port Fuel Injection (MFI) Fuel Pressure Gauge T80L-9974-B as outlined in Service Procedures-Fuel System Pressure Relief.
  1. Turn ignition switch to RUN position for three seconds repeatedly (5 to 10 times) until pressure gauge reads at least 270 kPa (30 psi). Check for leaks at fittings.
  1. Remove pressure gauge, start engine and recheck for leaks.
Hope this helps

Aug 13, 2011 | 1996 Mercury Mystique

2 Answers

Location of fuel pump for mazda mx5 2000


Removal & Installation
Through the trunk servicing panel...
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Rear package trim
    • Service hole cover
    • Fuel pump cover
    • Fuel pump connector
    • Fuel hoses
    • Fuel pump and gauge sender unit as an assembly
    • Fuel pump from the sender bracket

To install:

  • New O-ring set
  • Fuel pump to the sender bracket

NOTE

Pull the fuel pump down so that it is tight against the bracket.

  • Fuel pump and gauge sender unit as an assembly
  • Fuel hoses
  • Fuel pump connector
  • Fuel pump cover
  • Service hole cover
  • Rear package trim
  • Negative battery cable

Oct 14, 2010 | 2000 Mazda MX-5 Miata

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

1 Answer

How to change the fuel pump on a 1996 Pontiac Transport


For 1996 Pontiac Truck Trans Sport 3.4L SFI 6cyl check this procedure for Fuel Pump... there are two different electric fuel pumps used:
- A medium pressure twin turbine pump for vehicles equipped with Throttle Body Injection (TBI). - A high pressure roller vane pump for vehicles equipped with Sequential Fuel Injection (SFI).
(see Figure 1)


d7f6f20.jpg


Fig. 1: View of the fuel pump assembly and related components
The fuel pump is mounted to the fuel sender assembly inside the fuel tank. The fuel is pumped to the engine at a specified flow and pressure by the fuel pump. Excess fuel is returned to the fuel tank by the return pipe. The fuel pump delivers a constant flow of fuel to the engine even during low fuel conditions and aggressive vehicle maneuvers.

CAUTION When working on or near the fuel tank, be sure to observe the information molded on the bottom of the tank.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure.
(see Figure 2)


42fbc79.jpg

Fig. 2: Exploded view of the fuel pump-to-tank mounting components
  1. Drain and remove the fuel tank.
  2. Remove the fuel sender assembly.
  3. Disassemble the fuel pump strainer and the fuel pump: Note the position of the strainer in relation to the pump.
(see Figure 3)


c8d9af6.jpg


Fig. 3: Remove the fuel tank locking ring with a non-sparking (brass) punch.
  1. Support the fuel pump in one hand, and grab the strainer in the other hand.
    1. Rotate strainer in one direction and pull off pump. Discard strainer.
(see Figure 4)


3c2e4a1.jpg


Fig. 4: Exploded view of the fuel pump components
    1. Remove deflector.
  1. Disconnect the fuel pump electrical connector.
  2. Loosen the two connecting clamps, if equipped.
  3. Place the fuel sender assembly upside down on the work bench.
    1. Pull the fuel pump downward to remove it from the mounting bracket, then tilt the pump outward and remove it from the connecting hose or the fuel pulse dampener.
  4. It is recommended to replace the hose and clamps, if equipped.
CAUTION Do not run the pump unless submerged in fuel
To install:
  1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body, where equipped.
  2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.

Hope this help (remember rated this).

Jun 04, 2010 | 1996 Pontiac Trans Sport

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7018 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...