Question about 2000 Volkswagen Beetle

1 Answer

2000 Vollkswagen Bettle 1.8 Tubor 5 speed standard shift

Over heat light comes on. Engine runs hot and rough. Feels like the brakes are hard. It has aready melted the oil dip stick holder.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Is your car low on coolant? is the water pump bad? and if you have driven it for long while overheated you may have blown a headgasket causing coolant to enter the combustion chamber and causing it to run rough and eventually ceise up.

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my car having trouble shifting gears, gets stuck changing gears, has a hot smell after it has been running for a while,has a running a noise after its been turned off for a while


Sounds like you need oil in your transmission, low pressure light for hydraulics. Get it checked right away or it could seize up.
Make sure all your fluids are checked both for levels and leaks.
Your brakes may need looking at too.

Oct 10, 2016 | 2004 Nissan Maxima

1 Answer

2002 ford windstar rough idle


Sounds like you never diagnose any fault codes
& just continue to drive on

ABS,Brake light,Evap,now a failed transaxle

Sep 01, 2013 | Cars & Trucks

1 Answer

Car running rough at lower speeds; Check engine light, traction control, Cruise control light on, S# light flashing.


Have you had the computer checked for trouble codes yet ?
The codes would point you in the right direction to look for the cause.

Jul 29, 2012 | Cars & Trucks

1 Answer

Manual shift light blinks, chugs when accelerating.


Hi Seth, Check out your engine and gear box mountings! Regards John

Apr 01, 2012 | 1990 Ford Probe

2 Answers

Substantial Lost power from take off all the way to 5 th gear


sounds like restricted fuel filter or restricted exhaust.
your local exhaust shop can perform a simple and free test to see if the cat can is plugged.

Dec 31, 2009 | 2000 Chevrolet Camaro

1 Answer

I have a 2000 VW bettle tonight the check engine light, EPC Light, Brake light its Flashing< and the ABS light came on. What could be causing this Problem.


HAVE DEALERSHIP SCAN IT THEY HAVE SPECIAL SCANNER FOR TROUBLE SHOOTING ABS BRAKES SYSTEM.AND THE CHECK ENGINE LIGHT.THIS NOT HOME FIX.

Sep 30, 2009 | 2000 Volkswagen Beetle

4 Answers

2001 BMW 325i problem: Car runs very rough, but no warning lights


Sounds like a fuel problem , have you changed the fuel filter in a while ? could be the knock sensor or the knock sensor module needs to be replaced.

Jul 28, 2009 | 2001 BMW 325

1 Answer

Feels like the brake is always on & gains no speed


When was the last time you open the transmission ? Is it a standard, or automatic transmission ? When was the last time you change your breaks ? Jack the wehicle up, and try to turn the tires with your hand. your breaks might be too tight.

Jun 13, 2009 | 2006 Mitsubishi Lancer

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
2000 Volkswagen Beetle Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...