Question about Triumph Tr 7

1 Answer

My GT6 which has electronic ignition has no fire at the plugs

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 272 Answers

Check out your distributor and electronic ignition. I trust this helps you.

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 foreman TRX450SX just quit and want crank its getting no fire


Check the electronic ignition see if you have power at the key switch

Aug 14, 2016 | Cars & Trucks

1 Answer

Firingorder1974triumphspitfire mk4


***The recommended timing for a Mk1 or Mk2 Spit. Adjust as follows:1. Rotate the Vernier adjuster knob counterclockwise until it won't turn anymore.
2. Position the crankshaft so that the front cylinder is at TDC and ready to fire. (The pointer on the timing chain cover will be lined up with the timing mark on the pulley)
3. Rotate the distributor body clockwise until the points just begin to open (make sure the rotor is pointing to the #1 piston) A test lamp is helpful for this operation.
4. Tighten the distributor clamp to lock the distributor in place.
5. Rotate the vernier adjuster knob until you achieve 13 degrees of advance (each click of the adjustment knob is equal to 1 degree of advance)
Engine Tuning Data for the Triumph Spitfire and GT6 Distributor drive gear and firing order question Spitfire GT6 Forum...

Jun 14, 2016 | Cars & Trucks

1 Answer

1974 truimph spitfire mk4 firing order


Edward, Firing order 1-3-4-2 for spitfire. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Engine Tuning Data for the Triumph Spitfire and GT6
Distributor drive gear and firing order question Spitfire GT6 Forum...
getting spark plug wires back in the right order MGB GT Forum MG...
http://www.repairservicemanuals.com/Triumph

Jun 14, 2016 | Triumph Cars & Trucks

1 Answer

Overdrive slipping on my gt6


I don't think the overdrive can slip...my suspicion is the clutch friction disc has worn, and the extra load with od engaged is causing the slippage.

Apr 15, 2014 | 1971 Triumph GT6

1 Answer

Will a 1999 mazsda millinea distributer fire without the harmonic balance in place


1) you must test the a) ignition coil b) EI ( Module Electronic Ignition) However you can go to www.automecanico.com for to see the timing ignition according with your model and fix it. translate the website to english
see the chart attached and fix it. God bless you

10_5_2012_12_02_56_pm.jpg10_5_2012_12_04_18_pm.gif

Oct 05, 2012 | 1999 Mazda Millenia

1 Answer

Engine turns over, but there is no firing, I replaced plugs, wires, distributor cap and rotor, also replaced fuel pump, what other problems would cause vechicle not to fire. Would it have to be the...


It is possible that the trigger to the HT coil is absent and so there is no HT or firing. So check on the platinum points or the electronic ignition and check the PULSATING voltage on the HT coil negative side.
If there is trigger with no HT output then the coil is faulty. If not check the condenser and the points. Set the gap correctly or replace. If this has an electronic ignition then check the sensor and the circuit if there is a failure.

Aug 02, 2011 | Chevrolet Blazer Cars & Trucks

2 Answers

Need the spark plug diagram for a 77 gmc 454 engine


zjlimited_580.jpg

V8 engines with points-type ignition system Firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise



zjlimited_581.jpg

V8 engines with electronic distributor ignition system Firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise


Hope heslp.

Jan 30, 2011 | Cars & Trucks

2 Answers

I took of*** my spark plug wires working on my small block 350 pickup and I don't remember the the firing order to put the new wires back on. Is there a diagram anywhere or is it even that difficult to...


Next time number each lead before you remove it and no. the dissy cap as well

The firing order, which should be cast into the intake manifold, for the chevy small block V8 is 1-8-4-3-6-5-7-2. The firing order is the numerical sequence in which the spark plugs are fired. The insertion position of each spark plug wire around the circumference of the distributor cap can be found according to a clock face. The insertion sequence determines the firing order. The firing order is followed clockwise around the distributor cap starting from the 6:30 position with the 6:30 position being the number one cylinder spark plug wire.
On classic chevy small block engines that use ignition breaker points instead of electronic ignitions, the number one cylinder is the one immediately clockwise of the small metal sash cover on the distributor cap. The firing order starts here. There is no sash cover on the distributor cap for GM HEI electronic ignitions, and the firing order is the same, but starting at the 5:30 position.
The firing order makes sense if you know how the cylinders are numbered. The number one cylinder is the front most on the drivers side and 2 being the front most on the passenger side. From front to back, the cylinders are odd numbered on the drivers side, and even numbered on the passenger side.
See the diagram; Click to open a printable larger image in a new window. The firing order starts with the number one cylinder. We would connect the number one spark plug wire to the distributor cap terminal in the 6:30 position. distributor.pngSince the next cylinder in the firing order is 8 (passenger side rear), we connect the number 8 spark plug wire to the next distributor cap terminal (approximately 7:30 position) in the clockwise direction from number one. You need to be sure you continue the firing order in the clockwise direction around the chevy small block distributor cap from the last installed spark plug wire. Setting the rest of the firing order is just a matter of repetition. Be sure to count the spark plugs from front to back on each side of the motor to identify the correct cylinder number in the firing order.

Jun 21, 2010 | Cars & Trucks

1 Answer

Timing the cams and crank with a belt


  1. Note: Electronic Ignition engine timing is entirely controlled by the PCM. Electronic Ignition engine timing is NOT adjustable. Do not attempt to check base timing. You will receive false readings.

The CKP sensor is used to indicate crankshaft position and speed by sensing a missing tooth on a pulse wheel mounted to the crankshaft. The CMP sensor is used by the COP Integrated EI System to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The PCM uses the CKP signal to calculate a spark target and then fires the coil pack(s) to that target shown in Figure 51. The PCM uses the CMP sensor not shown in Figure 51 on COP Integrated EI Systems to identify top dead center of compression of cylinder 1 to synchronize the firing of the individual coils.
  1. The coils and coil packs receive their signal from the PCM to fire at a calculated spark target. Each coil within the pack fires two spark plugs at the same time. The plugs are paired so that as one fires during the compression stroke the other fires during the exhaust stroke. The next time the coil is fired the situation is reversed. The COP system fires only one spark plug per coil and only on the compression stroke.

    The PCM acts as an electronic switch to ground in the coil primary circuit. When the switch is closed, battery positive voltage (B+) applied to the coil primary circuit builds a magnetic field around the primary coil. When the switch opens, the power is interrupted and the primary field collapses inducing the high voltage in the secondary coil windings and the spark plug is fired. A kickback voltage spike occurs when the primary field collapses. The PCM uses this voltage spike to generate an Ignition Diagnostic Monitor (IDM) signal. IDM communicates information by pulsewidth modulation in the PCM.
  1. The PCM processes the CKP signal and uses it to drive the tachometer as the Clean Tach Out (CTO) signal.

2.5L V6

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by a pulse former within the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition timing is determined by the powertrain control module in response to engine operating conditions based on stored data tables or maps. Once ignition timing has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 5, cylinders 4 and 3 and cylinders 2 and 6) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This ensures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
---------------------------------------------------------------
2.0L 4 cynder

The ignition system consists of an ignition coil, spark plug wires and spark plugs.
The crankshaft position sensor signal is the basis for ignition timing calculations. The alternating voltage signal from the crankshaft position sensor is digitized by the powertrain control module. This digitized signal is then used to position the closing time of the primary circuit of the ignition coil.
Ignition angle is determined by the powertrain control module in response to engine operating conditions. Once ignition angle has been determined, the powertrain control module interrupts the current to the primary circuit of the ignition coil thus triggering the ignition spark which is supplied to the cylinders through the spark plug wires and spark plugs.
The ignition coils are triggered by the powertrain control module in pairs (cylinders 1 and 4 and cylinders 3 and 2) sending one ignition spark to the firing cylinder and one ignition spark to the corresponding cylinder on the exhaust stroke. This make sures that any unburnt fuel residues remaining in the cylinder on the exhaust stroke are re - ignited to provide cleaner exhaust emissions.
------------------------------------------------------------------------------------
Integrated Electronic Ignition System The Integrated Electronic Ignition (EI) System consists of a crankshaft position (CKP) sensor, coil pack(s), connecting wiring, and PCM. The Coil On Plug (COP) Integrated EI System uses a separate coil for each spark plug and each coil is mounted directly onto the plug. The COP Integrated EI System eliminates the need for spark plug wires but does require input from the camshaft position (CMP) sensor.
----------------------------------------------------------------------------------------

Apr 05, 2009 | 1998 Ford Contour

2 Answers

1990 Subaru Legacy shorted out the ignition coil. I replaced it and in less than 1 mile,it shorted out the new one.


Subaru engines (including Legacy and engines of many other automobiles, GM, etc.) have returned to so-called wasted spark ignition systems since advent of the electronic distributor-less ignition (having been used historically in early engines with magneto ignitions). With this approach, the ignition systems are less expensive and usually quite reliable. At the same time, however, a shorted spark plug (cracked or carbon clogged, etc.) (or bad ignition spark plug wire) grounds both the ignition spark and the false spark being used. This means that it also grounds the corresponding respective ignition spark of the other 180 degree out of phase cylinder (that uses the same the same coil because the spark current is connected to the spark plugs of two cylinders). Since such a defect allows more current to flow in the spark coil to two plugs when the resistance of the spark plug gap disappears due to a cracked plug, etc, it seems likely to hasten coil burn out if the spark plug/plug wire defect is not corrected before installing the new spark coil.

To explain further, wasted spark means that when a cylinder is ready to fire, it gets a spark to its spark plug while part of the spark (from the same coil and current) as a sort of copy is also sent to another cyclinder at the same time but when the piston in that cylinder is exhausting its ignited gases 180 degrees out of phase from when its spark is needed. When the second cylinder is ready to fire and receives its "spark, the first cyclinder the also receivesa "wasted" spark "copy" of the one needed by the second cylinder. Economy is achieved in manufacture because otherwise electronics would have to turn on and off four different spark coils to distribute four different sparks as needed to the four cylinders. With wasted sparks (which are cheap), because the spark current of one coil is connected (internally in the ignition coil unit) to two cylinders that are in the same position but 180 degrees out of phase in firing, the system can turn on and off two spark coils twice as fast with half the electronics and fire two cylinders that are 180 degrees out of phase. A four cylinder engine thus uses only two coils, a six cylinder engine, three coils, etc., in a wasted spark system.

Jul 27, 2008 | Subaru Legacy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Triumph Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

576 Answers

Are you a Triumph Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...