Question about Buick LeSabre

1 Answer

I need a print out on how to disassemble and and assemble my intake gasket and replace the gasket on my 94 buick lasabre.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 319 Answers

Please click this link and look about half way down for "1991-97 Vehicles".

GOOD LUCK!

Brian

Posted on Jul 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3800 motor has a rubber gasket on the 94 lasabre waterpump do I change the rubber gasket or leave it and just add the paper gasket


It's probably just a gasket made from sealant. Just scrape it off and make sure the surfaces are clean enough for the paper gasket

Aug 25, 2014 | 1994 Buick LeSabre

1 Answer

My 2001 Buick LaSabre "eats"


If there are no coolant leaks then check your engine oil to be sure it is not over full or foamy because if there is coolant getting into the oil it will cause irreversible damage to the engine. If the engine has ever over heated the head gasket/s could also be leaking and will need replaced.

May 16, 2011 | Buick LeSabre Cars & Trucks

2 Answers

Where is the pcv valve located on 94 buick lasabre?


The PCV valve is located under the hood, center, upper engine area, top of engine, mounted in passenger side of intake manifold. I hope this helps and good luck.

Apr 10, 2011 | 1994 Buick LeSabre

1 Answer

Ive got a chevy tahoe 2002 and the passenger side window wont roll up all the way. When i get it up all the way it slides down about 4 inches


Assuming you have power windows. Had similar problem on 2000 Buick LaSabre. Had to replace electric motor drive assembly inside of door. The motor moves a steel cable around nylon/plastic pulleys. In time the cable cuts into the pulley. Access motor assembly by removing inner door panel. I had to purchase assembly from the dealer ($$$). Digital snapshots as you disassemble will help you reassemble. Job took about 1.5 hours, and I had never done it before.

Feb 20, 2011 | 2002 Chevrolet Tahoe

3 Answers

How many miles does an 1997 Buick Lesabre usually last?


Gm says a 3800 engine should last ove 400,000 miles with normal service. This engine for 97 will probably need a new plastic intake manifold one day. They will leak coolant into the combustion chamber and some un-educated mechanics will tell you that it needs head gaskets as they don't have a head gasket problem. The oil pan may leak on this car too, replace it with a fel-pro perma dry gasket and it will stop it. Mine has 297,000+ miles on it.

Apr 10, 2010 | 1997 Buick LeSabre

1 Answer

94 Buick LaSabre Hesitation


Clean the sensor wire in the mass air flow sensor. Remove the tamper proof screws to remove the sensor holder and clean off the wire with carb spray or brake cleaner. Do not touch the wire with hands or rags.

Feb 24, 2010 | 1994 Buick LeSabre

1 Answer

Cant find pcv valve on 2000 buick lasabre


The PCV valve is hidden on top of the intake manifold down in a little enclosure. There are two small bolts holding the PCV cover. Often there is a fairly large vacuum line coming into the enclosure. Remove the cover and pull the PCV valve that sits down into a gasket.




201f7e7.jpg

Feb 18, 2010 | 2002 Ford F150 Regular Cab

2 Answers

Just put new spark plugs in 97 buick lasabre. Car now starts and runs, but is blowing out white smoke. Is this blown head gaskets? Does it have anything to do with the fuel pump put on 3 weeks ago?


these cars have issues with coolent getting into the intake... headgaskets are not one of the issues . check plugs for coolent. upper plastic intake has coolent flow in to chambers if u will, and over time they get micro cracks and brittle ...lower intake manifold gaskets are plastic also. ..cyl. heads are cast iron not alluminum . lower intake manifold is alluminum and upper intake is plastic .. on my lesabre a plastic 90 degree elbow connected to the lower intake manifold to the heater hose housing. the belt tensioner is connected to this housing im refering to. not saying for sure, but if it is this is usually why...

Jun 26, 2009 | 1997 Buick LeSabre

1 Answer

1997 buick lasabre custom


It sounds like you have a vacuum leak or intake gaskets leaking. Try this. Start the engine and let it reach the idle it want to go to. Get you a can of Brake Clean and spray it around the intake manifold (it on the top center of the engine, you may have to removed a plastic cover) If the engine idle changes up or down then the intake gaskets are leaking hence your vacuum leak. I hope this will help you.

Jan 04, 2009 | 1997 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...