Question about 1992 Lexus Es 300

1 Answer

I dont know where the knock sensor is located on the engine

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Http://i33.tinypic.com/20i9xt3.jpg

its in the middle of the engine..not easy to get to

Posted on Jul 25, 2008

×

6 Suggested Answers

  • 512 Answers

SOURCE: knock sensor location on a 2004 dodge neon

knock sensor is located under the intake manifold in front of the starter. what codes did you have?

Posted on Jan 07, 2009

BCally1
  • 133 Answers

SOURCE: Where is the Knock Sensor located on a 1994 Lexus ES300

  1. located on top of engine below intake manifoldgraphic.aspx?mod=reptiff&module_id=1&session_id=%7ba7aa889f-b7e3-42e1-9ece-3476a2533f69%7d&image_guid=95d24086&print_bw=0&

Posted on Jan 07, 2009

tripletauto
  • 1450 Answers

SOURCE: Where is the location of the knock sensor for a 2005 HD 2500 6.0

HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Posted on Jan 26, 2009

moparownr
  • 667 Answers

SOURCE: Where is the knock sensor located in 2000 chevy 5.3 v-8?

They are located below the intake manifold, you may have to remove the intake to change them. The sensors may be shot, they have a problem with water puddling in their mounting wells, after changing, seal the sensors with an RTV to keep water out of the wells

The Knock Sensor (KS) system detects engine pre-detonation. The Powertrain Control Module (PCM) retards the spark timing based on the signals from the knock sensors. The knock sensors produce an AC voltage when specific frequencies are detected. The knock sensor voltages are an input to the PCM. The amount of AC voltage produced is proportional to the intensity of the knock.
When you ****** timing fuel mileage goes down.

Posted on Apr 08, 2009

Toyota Guy
  • 42 Answers

SOURCE: Location of knock sensor on 1994 toyota 22vre engine

The Knock sensor on a 22re is located under the intake manifold on the engine block. to the upper left of the oil filter. With is the passenger side of the engine. I believe it is yellow in color. Not do be confused with the oil pressure sensor which is close by. The knock sensor has a larger electrical connector. Good luck it can be hard to get to.

Posted on May 06, 2009

  • 1 Answer

SOURCE: nissan xterra knock sensor

I have a 2000 Nissan Xterra my check engine light came on the scanner read knock sensor came up how to replace it and location

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 Chevy avalanche knock sensors location


Nathan, 2 Knock's are located under intake manifold.
Check the attached links,
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Engine Knock Sensor 2000 06 5 3L Silverado Sierra...

Knock sensor 5 3 4 8 6 0 replacement

05 Chevy Avalanche Knock Sensors

4 8 5 3 6 0 knock sensor replacement GM



Mar 06, 2016 | Cars & Trucks

1 Answer

Location of the knock sensor on a 1992 Buick Skylark


Here's a link Jon to your knock sensor removal. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

1992 Buick Skylark 2.3L MFI SOHC Quad 4cyl

The Knock Sensor is located: Under hood, driver side, upper engine area, below exhaust manifold, mounted in engine block

Jul 18, 2015 | Buick Cars & Trucks

1 Answer

2005 suburban 5.3 engine where are knock sensors located and how do you replace them


two knock sensors.under phlemm assy. replace cover gasket, two sensors and wire harness.

Jan 27, 2013 | 2005 Chevrolet Suburban

3 Answers

Check engine for knock sensor lighting up it says short/low bank 1


Check the wiring harnesses for bare or brittle spots. If none are found replace the spark plugs, all of them and spark plug wires. I know these are still fairly new but that is the next step. If you have over 60,000 miles on the vehicle it could be an issue with the timing chain but my experience tells me replace the crank Position sensor first if none of the other steps yield any results. Because these vehicles come with the power train warranties they do you can't really trust the Dealer Mechanics because they will do anything they can to prolong this to get the vehicle out of warranty.

Nov 03, 2011 | 2003 Nissan Murano

1 Answer

Need to know where knock sensor is located on a 2001 kia rio.


At center rear of engine compartment, by intake manifold support bracket.

Dec 23, 2009 | 2001 Kia Rio

3 Answers

Need to replace knock sensor/ O2 sensor 04 kia rio


IT IS IN THE SIDE OF THE ENGINE BLOCK, SCREWED INTO THE WATER JACKET OF THE BLOCK

Sep 18, 2009 | 2004 Kia Rio

1 Answer

I own a 2003 Chevrolet Express 3500 cargo van. The check engine light came on and the local hardware store, break out box indicates that the knock sensor circuit is the problem, bank 2. Which side of the...


OK, bank2 is the side where the #2 piston is on. Usually its the pasanger side. To be sure open the hood and see which cylinder head is more forward than the other. the cylinder head set back is the bank 2 side. The knock sensor is located on the bank side of the block. You dont need a special tool. only a wrench. Make sure you clear all codes after installation of sensor.

Jul 23, 2009 | Chevrolet Express Cars & Trucks

1 Answer

Knock sensor dont work for 2005 dodge durango


this problem is very seldom the knock sensor, it can be the harness connector at the sensor or the engine has excessive knock which will set a code, u did not mention the particular code so hard to say, the location of the knock sensor is the lower section of the engine block, it is screwed into what would normally be a block drain plug, if u replace it u need to torque it to whatever the factory spec is or it can cause it throw another code..

May 29, 2009 | Dodge Durango Cars & Trucks

4 Answers

Knock sensor location


The knock Sensors are located under the Intake Manifold at the top of your engine. The top will have to be taken off along with the intake manifold. Knock Sensors in past silverados used to have a problem with leaking water that corroded the sensors from washing the engine. Most times when you go to replace the knock sensor you will have to replace both along with the wiring harness that includes the the gaskets the knock sensors are surrounded by. After that you have to check the resistance to make sure you dont have any problems and then reinstall all parts along with a new intake manifold gasket. A good mechanic can do this for you in a day and charge you around $400. If you try to go to some place like a chevy dealer you will pay over $800. This is from experience of just replacing mine 2 weeks ago.

Dec 23, 2008 | 2004 Chevrolet Silverado

4 Answers

Nissan xterra knock sensor


It's the valley of the engine underneath the intake manifold. It's about an $800 job because the top of the engine has to come off. However, unless you have a supercharged xterra it shouldn't effect performance. Also, the knock sensor will not trip the check engine light, as it does not indicate a primary problem, so if your light is on you should have another code that should be fixed first.

Nov 05, 2008 | 2002 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...