Question about 1996 Dodge Neon

1 Answer

Replace power srearing belt - 1996 Dodge Neon

Posted by on

  • Anonymous Sep 18, 2008

    squeals when i turn

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There are three bolts on back side of p/s pump (13mm head) loosen bolts, there is a bolt on front of engine (15mm head) loosen, this will allow the pump slide down to replace belt, to tighten put pry bar on rad support and under the front of pump until the belt tension is proper, keeping tension on pry bar
tighten bolts.

Posted on Oct 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change poer assist belt on hyundai coupe 2.0ltr 2001?


Check the attached links,similar models to yours power steering belt replace.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

How To Install Replace Power Steering Belt 2001 06 Hyundai Elantra

Accessory Drive Belts Replacement 2001 Hyundai Accent

How To Install replace Alternator Belt 1999 06 Hyundai Elantra 2 0L


Mar 10, 2016 | Hyundai Cars & Trucks

2 Answers

I need to replace the belt tensioner on a 2000 Chysler Caravan with a 3.0L engine, with a/c. I would appreciation a diagram for properly installing the serpentine belt, and some instructions on how to...


Hi, I have pasted the procedure for belt replacement below. To replace the tensioner as well, first take the belt off. Then remove the pulley from the tensioner. This will expose the single bolt that holds the tensioner on. Replace the tensioner and then the pulley (if replacing all). Then reinstall the belt.

Alternator/Power Steering Pump Belt
The alternator/power steering pump belt is provided with a dynamic tensioner to maintain proper belt tension.
  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and safely support it with jackstands.
  3. Remove the right front splash shield.
  4. Release tension by rotating the tensioner clockwise (use a box-end wrench on the tensioner bolt shown in the picture.
  5. Remove the belt and install a replacement.
  6. Proper belt tension is maintain by the dynamic tension.
  7. Install the right front splash shield. Lower the front of the vehicle.
  8. Connect the negative battery cable.


  1. jturcotte_2078.gif


    Fig. Alternator/power steering pump belt tensioner bolt location


jturcotte_2079.gif

Aug 13, 2011 | 1996 Dodge Caravan

2 Answers

Power steering went out last nite and battery light came on serpoentine belt is loose


You'll need to replace the belt tensioner as it is probably weak and not keeping the correct tension on the belt.

Apr 02, 2011 | 2002 Ford Escort

1 Answer

I've replaced the power steering belt on my 1994 SVX and it is still squealing. The replacement stopped it for a week or so but it is just as bad as it was. I was told you can replace the bearings in a...


Well, I had a similar problem with a belt on a 1990 Olds Cutlass Calais that kept slipping until I sprayed it with 'belt dressing.'

I replaced the belt but it still slipped.
I would try that first before replacing the power steering pump itself.
I don't think that changing the bearings in the power steering pump would make a difference.
It's a belt problem.

Oct 13, 2010 | 1994 Subaru SVX

1 Answer

What do i do to get new belt on


FOR THE 3.0L ENGINE IF YOU REPLACE AC BELT LOOSEN TOP IDLER PULLEY CENTER BOLT. IF YOU REPLACING ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTMENT BOLT AND PIVOT BOLT.IF REPLACING POWER STEERING PUMP BELT LOOSEN POWER STEERING PUMP ADJUSTMENT BOLT AND MOUNTING BOLTS.****** FOR THE 2.4L ENGINE TO REMOVE POWER STEERING BELT LOOSEN TOP IDLER PULLEY.FOR ALTERNATOR AND WATER PUMP BELT LOOSEN ALTERNATOR ADJUSTER BOLT, PIVOT AND MOUNTING BOLTS.FOR AC COMPRESSOR LOOSEN LOWER IDLER PULLEY.

Oct 07, 2010 | 1996 Nissan Pickup

1 Answer

Power steering belt replacement for 1998 bmw 740i


your power steering pump should have a adjusting pinion nut.you loosen the pinion nut to loosen pump so you can replace belt.or you have a automatic belt tensionener you rotate tensioner clockwise to replace or remove belt.

May 23, 2009 | 2000 Renault 181

1 Answer

Alternator belt replacement of 1989 Toyota pickup truck . there are 2 belts to get past before we can replace the alternator belt. How is best to remove first two belts.


Start with the power steering belt it takes a 12 mm socket for the bolt in the power steering . also loosen the bolt on the power steering pump pulley. remove the radiator lower fan shroud. It just clips in. pull the power steering belt around the fan and out of the engine compartment then do the a/c belt. That is the best way I know how.

Mar 02, 2009 | 1989 Toyota Pickup SR5

2 Answers

Replacing a power steering pump on a 1996 Olds Delta 88 Royale


3 bolts should be holes in the pully too go thru with an extension if their are no holes in the pully then you nee a power steering pump pully remover it can be rented for 5.00 at auto zone

Feb 23, 2009 | 1996 Oldsmobile Eighty Eight

2 Answers

Loud squealing from power steering pump - do I need new PS pump?


Hi! The pulley could be worn or the belt is not properly adjusted.Causing the belt not to grip the pulley but slide on it,creating a friction.

Jan 15, 2009 | 1992 Toyota Celica

Not finding what you are looking for?
1996 Dodge Neon Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...