Question about 2002 Nissan Maxima

1 Answer

Need location of both crank angle sensors - 2002 Nissan Maxima

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 705 Answers

If your Max is 3.5 which it should be unless its 2001, than this Max has 3 sensors. 1 crank and 2 cam. Crank sensor is in the front of the bell housing, behing cooling fan, where engine and trans meet. than other 2 sensors are on sides of the cylinder head in both banks by the air filter box. They are 3 wire connectors and the cam sensors are bare to unplug and replug properly, so good luck. The connectors have these green slides, thast have to be pushed to unlock the connector, however when you going to replu it, you need to make sure, that the green lock/slide piece inside the connector slides back into position, or the sensor could unplug. You need to push the green slide and pull on the connector at the same time to unplug sensor.

Posted on Jul 20, 2008

6 Suggested Answers

localwonder
  • 6784 Answers

SOURCE: crank angle sensor location

The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

Posted on May 23, 2009

  • 1 Answer

SOURCE: audi a4 2.8 30v 1998 ack engine

It is mounted to the transmission bellhousing on the driver's side. The connector is mounted on the firewall and is a smaller, gray connector. You can reach the sensor from underneath.

Posted on Apr 01, 2009

  • 701 Answers

SOURCE: need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter

Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

Posted on May 06, 2009

66 chrgr
  • 1011 Answers

SOURCE: knock sensor 1996 v6 3.3 nissan pathfinder

the knock sensor is located under the intake PLENUM the crank sensor is located at the crank gear under the timing belt cover neither one is very much fun to do!

Posted on Jun 14, 2009

NismoMaster
  • 146 Answers

SOURCE: Ka24e locate the crank angle sensor

The sensor is located in the bottom inside of the distributor.

Posted on Jul 27, 2009

tunde007
  • 2382 Answers

SOURCE: where is the crankshaft position/crank

Hi, at the front of the crankshaft. if its near time for the timing belt, you want to replace it along with any pullies, tensioner and water pump


The crankshaft position sensor is mounted on the engine near the crankshaft.

Operation

The crankshaft position sensor is a Hall-Effect sensor that senses the crank angle (piston position) of each cylinder and converts it into a pulse signal. The signal from the sensor is relayed to the ECM to indicate engine rpm and the position of the crankshaft.

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor in place.
  4. Remove the sensor from its mounting. To install:
    1. Installation is the reverse of the removal procedure.
    2. Clearance between the sensor and the sensor wheel should be 0.020-0.059 inch. 2002-2005
      1. Properly connect the scan tool.
      2. Start the engine and allow it to idle.
      3. Be sure the idle position switch is ON.
      4. Specifications are as follows:

        Temperature - 4°F, test specification 1500-1700 RPM Temperature 32°F, test specification 1350-1550 RPM Temperature 68°F, test specification 1200-1400 RPMTemperature 104°F, test specification 1000-1200 RPM Temperature 176°F, test specification 650-850 RPM

Posted on Mar 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the crank sensor on a 2009 Nissan Titan v8 truck?


i think it's the starter. On most nissans, the starter and the crank position sensor are close to each other. Some nissans have 4 position sensors, between crank sensor, crank angle sensor, cam position sensor, and sensor sensing sensor, oh and cam angle sensor. Oh wait, maybe it's a bad ground. Nope, gotta be the staerter.
25440212-xipalmoknr3fbjmp51kycajc-3-0.jpg

25440212-xipalmoknr3fbjmp51kycajc-3-1.jpg

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

Where is crank angle sensor


Crank angle sensor is located on bottom passenger side of motor by the crank pulley

Apr 28, 2014 | 2002 Suzuki Aerio

1 Answer

We are trying to find the crank angle sensor in a holden vectra


crank angle sensor located on engine block lower where fly wheel would turn.

Jan 31, 2013 | Cars & Trucks

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

2 Answers

Ka24e locate the crank angle sensor


The sensor is located in the bottom inside of the distributor.

Jun 30, 2009 | 1997 Nissan Pickup

1 Answer

Crank sensor location


Look around the bottom of cylinder block. Or near where the flywheel is to, because the crank angle sensor works from missing teeth or magnets on the flywheel or a cog/wheel fixed to the crankshaft.Hope this helps

May 31, 2009 | 1992 Audi 100

1 Answer

Crank angle sensor location


The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

May 23, 2009 | Nissan Cars & Trucks

1 Answer

Need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter


Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

May 06, 2009 | Pontiac Sunfire Cars & Trucks

Not finding what you are looking for?
2002 Nissan Maxima Logo

182 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...